Subscribe to Our Youtube Channel
Related Manuals for Bushranger MC-PX-2
Summary of Contents for Bushranger MC-PX-2
- Page 1 Hedge Trimmer Attachment MC-PX-2 MC-PS-2 MC-PL-2 Owner’s/ Operator’s Manual Completely read and understand this manual before using this product.
-
Page 2: Table Of Contents
It is essential that any operator of this Multi-cutter reads and understands the contents this manual before using the Multi-cutter. For additional assistance, contact any local authorized BUSHRANGER dealer. Important Notice The benefits to the consumer given by this warranty are in addition to other rights and remedies of the con- sumer under a law in relation to the goods or services to which this warranty relates. -
Page 3: Safety Instructions
5. Inspect the tool attachment and replace any parts that are cracked, chipped or damaged before using the Multi-cutter. 6. Never use a tool attachment or replacement parts that are not approved by BUSHRANGER. 7. Maintain the Multi-cutter according to the recommended maintenance intervals and procedures in the Maintenance section beginning on page 11. -
Page 4: Fuel Safety
9. Keep a firm footing and balance. Do not overreach. 10. Use the right tool for the job. Do not use the Multi-cutter for any job that is not recommended by BUSHRANGER. ＿ 3 ＿... -
Page 5: Safety And Instruction Decals
• The distance between the machine and electrical power line shall be at least 10m. Maximum speed of output axle, min Guaranteed sound power level 110 dB(A). Product Description MC-PX-2 MC-PS-2 1. Saw chain 2. Guide bar 3. Regulating screw 4. -
Page 6: Assembly
Assembly Guide bar and saw chain installation CAUTION ・ In order to prevent cuts, be sure to wear gloves when handling the guide bar and saw chain. ・ Maintain the tension of the saw chain properly at all times. ・ If not enough tension is applied to the saw chain it can easily be dislodged when the saw chain is in motion. -
Page 7: Installing Shaft Assembly And Gearcase
Installing Shaft Assembly and Gearcase Attach the shaft assembly to the pruner gearcase assembly. Driveshaft Note: Carefully inspect both side of the shaft assembly. The Shaft Assembly arrow marking side of the shaft assembly positions to the power unit. The no marking side of the shaft Locating Hole assembly connects to the gearcase assembly. -
Page 8: Idle Speed Adjustment
If idle speed adjustment is necessary, and after adjustment the cutting attachment rotates or the engine stalls, stop using the Multi-cutter immediately! Contact your local authorized BUSHRANGER Dealer for assistance and servicing. Before Operation Chain Oil 1) Adding oil 1. - Page 9 2) Regulating oil discharging rate The regulating screw has three positions, Minimum, Interme- diate and Maximum, only. The regulating screw is set to Intermediate at the time of ship- ping. It is recommended that the product be used with this setting for ordinary use.
-
Page 10: Operation
Operation DANGER ・ Do not stand immediately below the branch that is to be cut. The branch may fall directly below and the branch may also bounce off other branches or the ground in an unexpected direction and cause injury to the worker. ・... - Page 11 Pruning thick branches Attempting to cut a thick branch in one go often results in the guide bar jamming in the branch or otherwise encountering difficulties in cutting. The method described below makes cutting thick branches easier: 1. First of all, cut a section slightly away and on the lower side of the desired area of the branch to be cut.
-
Page 12: Maintenance
Maintenance Sharpening saw chain 30° Whenever wood chips become small and fine or the wood cannot be cut without pressing the pruner hard against it, then it may be necessary to sharpen the saw chain. 1. Tighten the saw chain slightly firmer than usual then se- cure the pruner’s main unit. - Page 13 Guide bar care 1. When work using the pruner is finished for the day, re- move the guide bar and saw chain from the pruner. 2. Remove any wood chips or other particles attached to the groove of the guide bar or in the oil hole. Be particularly certain that no particles are clogging the oil hole.
-
Page 14: General Cleaning And Tightening
・ Always turn off your Multi-Cutter before you clean or perform any maintenance on it. The BUSHRANGER Multi-Cutter will provide maximum performance for many, many hours if it is main- tained properly. Good maintenance includes regular checking of all fasteners for correct tightness, and cleaning the entire machine. -
Page 15: Specifications
Specifications MT262 with MC-PX-2 MC-PS-2 MC-PL-2 Weight (kg) ※ 1 Engine Displacement (cm 25,4 Fuel Tank Capacity (L) Carburetor Diaphragm Type Ignition System Solid State Spark Plug NGK BPMR8Y Spark plug Gap (mm) 0,6-0,7 Fuel Mixture Two-stroke Oil Mix 50:1 Ratio... - Page 16 11 Sodium Street, Narangba Qld 4504 P/N.241983-01 GB 1909 IN...
Need help?
Do you have a question about the MC-PX-2 and is the answer not in the manual?
Questions and answers