Bushranger B2301 Operator's Manual
  1. Manuals
  2. Brands
  3. Bushranger Manuals
  4. Trimmer
  5. B2301
  6. Operator's manual

Bushranger B2301 Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

TRIMMER
B23

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the B2301 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Bushranger B2301

Summary of Contents for Bushranger B2301

  • Page 1 TRIMMER...
  • Page 2 RESPOOLING NYLON HEAD................11...
  • Page 3 Line Trimmer Line Trimmer B2301 Flexible drive shaft 9500/9500 6.03 98.2 108.3 Nylon head Loop Air cooled, 2 stroke oil Petrol cord on this trimmer...
  • Page 4 better operate the tool safely.
  • Page 5 better operate the tool safely. For starting and stopping the machine.
  • Page 6 complies with Australian Standards.
  • Page 7 petrol...
  • Page 11 squeeze foam 15.TROTTLE LOCK BUTTON is used to hold the throttle trigger at a high idle position for starting. TROTTLE LOCKOUT...
  • Page 12 HANDLE ASS'Y Fig. 1 INSTALLING HANDLE (Refer Fig. 1) Handle comes in two parts, plus four screws. Fit bottom half to shaft and place top half on top. Align the four screws and tighten. Position handle in a operating position and tighten four M5X40 screws.
  • Page 13 (Refer Fig. 2) Fig. 2 QUICK LOAD HEAD - RESPOOL Respooling nylon head (Refer Fig. 5a); Step 1 – Line up mark on centre bump knob with arrow on top cover. Refer to circles. Step 2 – Measure out 4m of 2.4mm nylon line and insert one end into anyone of the Step 1 Step 2...
  • Page 14 DISASSEMBLY Disassembly of Nylon Head (Refer Fig. 5b); Step 1 - Push in tabs - one on each side on nylon head. Refer to circle Step 2 – Remove top cover. Step 3 – Remove spool. Step 4 – Take note of Spring. Step 1 Step 2 Reassemble of Nylon Head...
  • Page 15 line trimmer loop Line trimmer...
  • Page 16 line trimmer line trimmer line trimmer...
  • Page 17 CUTTING WITH A NYLON HEAD The proper debris shield must be in place on the unit when nylon cutting line is used. The cutting line can around if too much line is exposed. Always use the plastic debris shield with when using nylon cutting heads.
  • Page 18 (Fig. 8) (Fig. 8) on this trimmer (Fig. 9 &10) (Fig. 9) (Fig. 10)
  • Page 19 unleaded petrol air cooled, 2 stroke petrol petrol unleaded petrol PETROL-40 PART PETROL 40 PART petrol PETROL unleaded petrol...
  • Page 20 PETROL PETROL PETROL...
  • Page 21 Ignition switch (stop switch) Throttle lock Safety lever (Fig. 11A) (Fig. 11B) Throttle trigger Fig. 11A (Fig. 11B) (Fig. 11A) (Fig. 11B) down Fig. 11B (Fig. 11B) (Fig. 11B) (Fig. 11B) (Fig. 11A) Starter handle position (Fig. 11B) (Fig. 11B) (Fig.
  • Page 22 (Fig. 12) Fig. 12 Bushranger...
  • Page 23 (Fig. 13) Fig. 13 NGK-CMR7A Fig. 14 (Fig. 14)
  • Page 24 To avoid line trimmer...
  • Page 25 Remove with...
  • Page 26 Run out Cylinder Petrol...
  • Page 27 Warranty Conditions 1. Australian Consumer Law (REG. 90): The benefits to the consumer given by this warranty are in addition to other rights and remedies of the consumer under a law in relation to the good or services to which this warranty relates. Our goods come with guarantees that cannot be excluded under the Australia Consumer Law.
  • Page 28 Copyright © Roy Gripske and Sons Pty. Ltd. 2018. All rights reserved. 1012. Images are for illustrative purposes only. Bushranger is a trademark of Roy Gripske & Sons Pty Ltd. PLP shall not be liable for technical or editorial errors or omissions ®...

This manual is also suitable for:

L2301

Table of Contents

Save PDF