Advertisement
Quick Links
BL-OPC • BL-ESD • BLQ-CR
BLQ-ESD • BLQ-CR-ESD
Suction • BL-SS
1-35-1 Oshiage, Sumida-ku Tokyo, Japan
TEL: +81 (JAPAN) 3-6661-8821
FAX: +81 (JAPAN) 3-6661-8828
19A
Brushless Driver
BL Series
Operation Manual
(May 2019)
BL-2000
BL-3000
BL-5000
BL-5000-15
BL-5020
BL-7000
BL-7000HT
HIOS Inc.
(anti-static electricity
is standard)
Operation Manual No.: ET-A010
Utilizing 100％ post-consumer
recycled paper pulp
Advertisement
Related Manuals for HIOS BL Series
Summary of Contents for HIOS BL Series
- Page 1 Brushless Driver BL Series Operation Manual (May 2019) BL-2000 (anti-static electricity is standard) BL-3000 BL-5000 BL-5000-15 BL-5020 BL-7000 BL-7000HT BL-OPC • BL-ESD • BLQ-CR BLQ-ESD • BLQ-CR-ESD Suction • BL-SS HIOS Inc. 1-35-1 Oshiage, Sumida-ku Tokyo, Japan TEL: +81 (JAPAN) 3-6661-8821 FAX: +81 (JAPAN) 3-6661-8828 Operation Manual No.: ET-A010...
-
Page 2: Name Of Parts
Thank you for your purchase of the BL-2000, BL-3000, BL-5000 or BL-7000 brushless driver. 1. Name of Parts BL-2000 BL-3000 Driver cord Driver cord Driver cord plug Joint ring Joint ring Hanger Hanger Driver connector Rotation direction switch Rotation direction switch Switch lever Switch lever... - Page 3 BL-7000 BL-5000 Driver cord Driver cord Driver cord plug Hanger Hanger Joint ring Driver connector Lever/push-to -start switch Rotation Rotation LEVER direction direction switch switch PUSH Switch Switch lever lever Torque adjustment nut Joint shaft collar 2. Accessories • Bits •...
- Page 4 Screw size Tapping screw 1.0 - 2.0 2.0 - 2.3 2.0 - 3.0 2.0 - 2.6 Weigh (g) HIOS Shank Bit type H5 & 5 HEX or H5 & 5 HEX or — HEX Shank 1/4 HEX 1/4 HEX 1/4 HEX ○...
- Page 5 （ WD cut shape ） ■ Power Supplies The Brushless Driver must be operated together with a Power Pack. Powering the Brushless Driver with the Hios T-45BL and the T-70BL Power Pack will insure operation of the driver at its full capacity. ● BL driver and Power Pack combinations Max. number of drivers...
-
Page 6: Pre-Operating Preparations
substances. 4. The driver does not require lubrication and should not be lubricated. ■ Pre-operating Preparations 1. Check that the proper Power Pack is being used with the driver. 2. Connect the Power Pack to plug AC100 to 240 V . 3. -
Page 7: Operating Procedure
■ Operating Procedure 1. Attach a bit to the driver. (See "Attaching a Bit" below) • If using model BL-3000, remove the torque adjustment nut cover before attaching a bit. 2. Set the driver to clockwise or counter-clockwise rotation as desired, then push the switch lever to check that the driver turns in the correct direction. - Page 8 ■ Torque Adjustment Torque is controlled by the tension on a spring inside the torque adjustment nut. If set the nut tighter, the output torque is higher. • The adjustment torque scale does not give the actual output torque. Please regard the output torque graph as an approximate guide.
- Page 9 Repeat the procedure until you arrive at the desired torque setting. It is recommended that a Hios torque meter be used to measure torque. Use the HP series for measurement of the driver's torque setting and the HDP series or the HDM series to measure loosening or tightening torque of screws.
- Page 10 ■ Approximate Guidance of Output Torque (during HI input) BL-2000 BL-3000 BL-2000SS BL-3000SS* N•m N•m 0.25 Black (installed) BL-3000 White 0.15 BL-3000SS* Yellow White (attached) 0.05 0.03 0.02 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Scale ring setting Scale ring setting BL-5000 BL-5000-SS...
- Page 11 - 11 -...
- Page 12 - 12 -...