1. Manuals
  2. Brands
  3. HIOS Manuals
  4. Power Tool
  5. Neji Taro II HS-35
  6. Operation manual

HIOS Neji Taro II HS-35 Operation Manual

Automatic screw feeder hs series
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Neji Taro II
HS series
HS-35 　 HS-40 　 HS-50 　
Operation Manual
Read this manual before using this device.
Current as of October 2016
HIOS Inc.
　
111-6, Akiyama, Matsudo City, Chiba Prefecture, 270-2223
Phone:81-47-392-2001 FAX:81-47-392-7773
Automatic Screw Feeder
Utilizing 100% post-consumer
Operation Manual No. ET-D003
recycled paper pulp
16A

Advertisement

Table of Contents
loading

Related Manuals for HIOS Neji Taro II HS-35

Summary of Contents for HIOS Neji Taro II HS-35

  • Page 1 HS-35 　 HS-40 　 HS-50 　 　 Operation Manual Read this manual before using this device. Current as of October 2016 HIOS Inc. 111-6, Akiyama, Matsudo City, Chiba Prefecture, 270-2223 Phone:81-47-392-2001 FAX:81-47-392-7773 Utilizing 100% post-consumer Operation Manual No. ET-D003 recycled paper pulp...

  • Page 2: Table Of Contents

    Contents 5. Operating Procedures and Operational Checks････ 7 6. Trouble Shooting･･････････････････････････････ 11 1. Before Use････････････････････････････････ 1 Maintenance ････････････････････････････････ 14 2. Important safety instructions･････････････････ 1 8. Specifications････････････････････････････････ 16 3. Parts of Names････････････････････････････ 2 9. External Diagram･････････････････････････････ 18 4. Checks and Adjustments before Operation････ 3 10.

  • Page 3: Parts Of Names

    3. Parts of Names Note: ① The design of bit-guide has been changed form V-type to bowl-type since September,1998. However, the operation method is same as the former V-type , therefore, the descriptions and the drawings for the V- type are still used in this manual. Pleas be careful that the bit type have been changed.(See p.10) ②...

  • Page 4: Checks And Adjustments Before Operation

    4. Checks and Adjustments before Operation . Check screw type Before operating HIOS your screw feeder, make sure You can easily replace the rail unit to match the diameter of the screw you wish to use. Check the screw number shown on the front of the rail unit to make sure your using correct diameter screw.
  • Page 5 4-2. Checking and Adjusting he Brush Brush Check the height of the brush. Ensure that the brush check/adjustment procedure is completed while the brush is placed in a horizontal position as shown at right. To place the brush in a horizontal position, rotate the timing shaft with the Allen wrench supplied with the machine.
  • Page 6 4-3. Checking and Adjusting the Passage Plate Drop the employed screws into the rail groove. Slide the screws to the Passage plate Passage plate retaining screw passage window section and check or adjust the passage plate height. Check that the clearance between the passage window upper end and Adjustment the screw heads is not greater than about 0.5 mm and that the screws can pass the passage window.
  • Page 7 If the holding plate (screw guide1) height needs to be adjusted, pro- Bit guide Bit guide assembly height ceed as directed below. adjustment screw Tilt this machine or operate it so that the screws are delivered to the Clockwise rotation → Descent Counterclockwise →...

  • Page 8: Operating Procedures And Operational Checks

    4-6. Checking and Adjusting the Bit Guide Holding plate Place five to ten screws in the rail and tilt this machine until Holding plate set screw they hit the stopper on the rail assembly. Rail set screw When the internal shutter is closed, the screws cannot go Bit guide through the passage plate.
  • Page 9 5-2. Operating this machine Connect the accessory AC adapter plug to the DC jack on the Power switch rear of this machine, and the other side to a power outlet. Indicator lamp incorporated Turn on the main power switch. The lamp incorporated in the power switch will illuminate.
  • Page 10 This machine is equipped with a timer. ・The timer setting can be adjusted according to the screw type. Function descriptions Time setting Increase The actual screw feeding speed varies with screw type. Decrease This machine continues running while there is no screw in the screw removal area of the escaper section.
  • Page 11 5-3. Picking up the screw Attach a bit to your electric screwdriver to match the head of the screw. Refer to the following. Bits Screw dai. Shap of bit. M3.5 M4.0 H4,H5 #2 Φ3.2 M5.0 Shaft of stepped Phillips head ①...

  • Page 12: Trouble Shooting

    6. Trouble Shooting Caution: Be sure to turn off the power switch of the feeder before making any adjustments. Problem Cause Remedy - No power is supplied. - Ensure that the AC adapter is properly connected to The machine does not start when power a power source.
  • Page 13 Problem Cause Remedy - The clearance between the holding plate - Shift the holding plate (screw guide 1) upward. The screws on the rail do not feed (screw guide 1) and screw heads is Use the Quicher in a tilted position. smoothly.
  • Page 14 Problem Cause Remedy The overload protection circuit is activated. - Turn the power switch off and then back on. The machine comes to a sudden stop. If the operation comes to a stop again, the probable causes are: There are too many screws in the screw bin.

  • Page 15: Maintenance

    7. Maintenance Rail front-rear position lock screw Rail lateral surface CAUTION Before performing any maintenance, turn off the Rail groove power switch and remove all the loaded screws from this machine. Rail upper surface 7-1. Cleaning the Rail and Rail Guide Wall Rail assembly When the rail groove becomes dirty, the screw feeding speed may be affected.
  • Page 16 7-2. Replacement Procedures Replacing the rail assembly The rail assembly of this machine can easily be replaced. Brush bracket 2 Brush Brush bracket 1 If the loaded screws do not smoothly feed after cleaning Brush unit screws or if you intend to use a different screw diameter, replace the rail assembly.

  • Page 17: Specifications

    8. Specifications NOTES - The transformer-type AC adapter attached to the machine has a Input: AC100V 50/60Hz Power supply (Transformer type) nominal output of DC 12V-500mA; during application, it is designed Output: DC 12V 500mA Dimensions (mm) 134(W) x 215(D) x 136 (H) mm to supply an average output at about 15V to the screw feeder.
  • Page 18 Specification Screw feed- Screw Rail model No. Passing plate model No. er model size HS-35 M3.5 HS-R35 HS2-01008-35 HS-40 M4.0 HS-R40 HS2-01008-40 HS-50 M5.0 HS-R50 HS2-01008-50 Replacement parts Rail Passing plate Brush assembly HS2-HIOS01143 Motor dirve assembly Motor HS2-04500-1 HS2-09582-05 - 17 -...

  • Page 19: External Diagram

    9. External Diagram 34.7 29.6 uniit:mm - 18 -...

  • Page 20: The Following Table Is For China Rohs2

    10. The following table is for China RoHS2 If you are asked by China Customs, please show this table to them. In addition, the China RoHS marks also is required at the product and product box. At the product, you can find it at the bottom and it is marked on the product box. If you cannot find the mark, please ask your distributor.

This manual is also suitable for:

Neji taro ii hs-50Neji taro iihs-40

Table of Contents