Advertisement
Quick Links
*Operation Manual for BLG-BC1 series is attached with a product.
111-6, Akiyama, Matsudo, Chiba Pref. Japan, 270-2223
Brushless Driver
BLG-4000
BLG-5000
BLG-5000-15
BLG-5000-20
BLG-5000-HT
BLG-BC1*
(BC1:With Built-in screwdriver)
BLG-OPC
(OPC: For Screw Counter)
Operation Manual
(As of November 2013)
TEL: +81 47 392 2001
FAX: +81 47 392 7773
Operation Manual No ET-A011
Utilizing 100% post-consumer
recycled paper pulp
13C
Advertisement
Related Manuals for HIOS BLG-4000
Summary of Contents for HIOS BLG-4000
- Page 1 Brushless Driver BLG-4000 BLG-5000 BLG-5000-15 BLG-5000-20 BLG-5000-HT BLG-BC1* (BC1:With Built-in screwdriver) BLG-OPC (OPC: For Screw Counter) *Operation Manual for BLG-BC1 series is attached with a product. Operation Manual (As of November 2013) 111-6, Akiyama, Matsudo, Chiba Pref. Japan, 270-2223...
- Page 2 ■ Names of Parts BLG-4000 (lever start type) Driver cord (5P) Driver cord plug The shapes of both plugs are the same (5P) BC1, OPC cord plug (6P) Hanger Driver connector FOR/REV switch FOR: Forward OFF: Neutral REV: Reverse Joint ring...
- Page 3 (HIOS shank) Accessories ● Bits ● Torque adjustment spring There are 2 torque adjusting springs for BLG-4000. In the BLG-4000, stronger spring (Red) is installed. If you want to use weaker spring then replace with accessory (White) spring. Select the sprig depends on your fastening torque.
- Page 4 (r.p.m) ±10% Machine screw 1.4 - 2.6 2.0 - 3.0 Screw size (mm) Tapping screw 1.4 - 2.3 2.0 - 3.0 Weight (g) HIOS Shank (Standard) H5 & 5HEX type Hexagonal Shank 1/4HEX or 1/4HEX T-30BL ○ Power Supply* T-70BL ○...
- Page 5 ■ Power Supplies The Brushless Driver must be operated together with a Power Supply. Powering the Brushless Driver with the Hios T-30BL and the T-70BL Power Supply will insure operation of the driver at its full capacity. ● BLG driver and Power Supply combinations Max.number of drivers...
-
Page 6: Operating Procedure
“Switch Lever”. Using sharp parts, such as tweezers, move the selection SW to “P” (push) near “L ←→P” mark. Switch lever shaft screw Switch Lever POWER OF HIOS "L←→P" select switch is at the side of this section. Note: Do not press or hit the SW, otherwise you may damage the SW or body case. -
Page 7: Attaching A Bit
For BLG-5000, pull-up the “Joint-shaft collar” and insert the bit. l Check that the bit is fixed firmly. l Use genuine parts for Hios Shank H4 ( ∅ 4) or H5 ( ∅ 5). How to adjust the torque BLG-4000 has two torque adjustment springs: for high... - Page 8 To decrease the rotation speed according to work type, set 20V as the power output. Using the screw counter You can use BLG-4000-OPC or BLG-5000-OPC by con- necting it to the power supply BLOP-STC3 with screw coun- ter or to the separate counter BLOP-SC1 , BLOP-SC3. For details of handling, please refer to the operation manual of the screw counter to be used.
- Page 9 Mini separate counter BLOP-SC3 BLG-4000-OPC BLG-5000-OPC (The shape of the driver cord (6P) is the same at both ends) Note: Use spring balancer with BLOP-SC3. Do NOT use BLG-4000 or 5000 horizontally with BLOP-SC3. - 8 -...
- Page 10 • If the above is not the case, or the problem cannot be solved, stop operation immediately and contact your distributor for repair. l Use the HIOS torque meter to check the screw tightening torque. • Use HP series for electric driver torque setting. • Use HDP series for measuring screw loosening torque and retightening torque. - 9 -...
- Page 11 ■ Output torque guide (HI input) BLG-4000 BLG-5000 BLG-4000BC1 BLG-5000BC1 BLG-4000-OPC BLG-5000-OPC N ・ m N ・ m (Installed) White (Accesso- 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Torque scale Torque scale...