Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Angelcare AC215
Summary of Contents for Angelcare AC215
- Page 1 FOR YOUR PEACE OF MIND OWNER’S MANUAL VIDEO, MOVEMENT & SOUND MONITOR Model AC215...
-
Page 2: Table Of Contents
, stand behind all of our products. ® If you are not completely satisfied or have any questions, United States and Canada: Please contact us at: angelcare@cdecinc.ca Other countries: Please contact your local distributor. FCC AND IC REGULATIONS RF radiation exposure statement The Nursery Unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. -
Page 3: Warnings
This monitor SHOULD NOT be used incorrectly replaced. The Parent Unit battery is a as a medical device, nor as a device to prevent replaceable Li-Ion battery. Only use the Angelcare Sudden Infant Death Syndrome (SIDS). recommended replacement battery. In both units, 2. - Page 4 Sensor Pad measuring Any mounting of the product should follow the at least 33 x 33 cm and 6 mm thick. Only use manufacturer’s instructions. your Angelcare ® monitor in a stationary sleeping 15.9 Unplug this appliance during lightning storms environment such as a crib where the Sensor or when not used for long periods of time.
-
Page 5: Setup Requirements
16.12 Remove batteries from both units if you store installation. If this equipment does cause harmful the product over 30 days because the batteries interference to radio or television reception, which could leak and damage the product. can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct 16.13 Discard ‘dead’... -
Page 6: Step 1 - Charging The Parent Unit (9 Hours)
STEP 1 - CHARGING THE PARENT UNIT (9 HOURS) 1) Connect the adapter to the Parent Unit and into an electrical outlet. 2) Charge the unit for 9 continuous hours (prior to first use). NOTE: To optimize your battery performance please refer to Battery Guidelines in the Troubleshooting section. -
Page 7: Step 2 - Installing The Sensor Pad
STEP 2 - INSTALLING THE SENSOR PAD Cord covers 1, 2, 3, 4: Position on floor Cord cover 4: Contains double sided tape to securely install beneath crib leg Cord cover 5: Position vertically between mattress support and floor Cord cover 6: Sensor Pad with pre-installed cord covers Place under the mattress 2.1 - SELECT A LOCATION FOR THE NURSERY UNIT... - Page 8 4) Bring the first 4 cord covers down the floor, and keep the 5 cord cover vertically, along the backside of the crib leg, (between the mattress and the inside edge of the crib). 5) Remove any cord slack to make sure no parts of the cord are loose.
-
Page 9: Step 3 - Setting Up The Nursery Unit
TURNING ON YOUR MONITOR 1) Press and hold the Parent Unit ON/OFF button for 2 seconds until LCD screen is turned ON. Angelcare’s logo will be shown for 1 second. 2) Slide the Camera ON/OFF switch to the ON position 3) The Parent Unit will display Video mode screen. -
Page 10: Step 5 - Testing And Getting To Know Your Monitor
2/3 Full Full STEP 5 - TESTING AND GETTING TO KNOW YOUR MONITOR The Angelcare ® monitor can be used with the pre-program factory settings or you can also customize your settings to your preference. Main menu on the LCD display shows the different operation settings. - Page 11 TO STOP THE ALARM On the Parent Unit, press any key Press the Pager/Hold to stop the alarm. button on the Nursery Unit. TO ADJUST THE SENSOR PAD SENSITIVITY LEVEL: 1) Press Menu/Select button to access main menu. 2) Select the Settings icon to access sub-menu. 3) Select the Movement Sensitivity icon.
- Page 12 LCD screen. we recommend that you fully recharge them. YOU ARE NOW READY TO USE YOUR MONITOR The Angelcare ® monitor can be used with the pre-program factory settings or you can also customise your settings to your preference.
-
Page 13: Step 6 - Activating And Deactivating Additional Functions
STEP 6 - ACTIVATING AND DEACTIVATING ADDITIONAL FUNCTIONS IMPORTANT When in the menu or sub-menu modes, sound transmission between Parent and Nursery Units will be temporarily deactivated. ONLY the movement detection alarm will remain active (if function is activated). 6.1 - SOUND TRANSMISSION (VOX) Your monitor is ‘Sound Activated’. - Page 14 6.3 - THERMOMETER 1) Press Menu/Select button to access TO CHANGE THE MEASUREMENT UNIT: main menu. 2) Select the Temperature icon to access sub-menu. 3) Select the ˚C ˚F icon. 4) Use the up and down arrows to change from Celsius to Fahrenheit. ºC ºC ºC...
- Page 15 6.4 - SCREEN SAVER 1) Press Menu/Select button to access Allows you to set the screen saver starting point. main menu. 2) Select the Settings icon to access sub-menu. 3) Select the Screen Saver icon. 4) Use the up and down arrows to select timed delay before Video mode turns into Screen Saver mode.
- Page 16 TO STOP THE PAGING SOUND: Press the Press any button Nursery Unit’s on the Parent Unit. Pager/Hold button 6.8 - ZOOM MODE Allows you to zoom in to twice the normal view. 1) Press and release the Zoom button on the Parent Unit. 2) The Zoom icon will appear at the bottom left corner of the screen.
-
Page 17: Troubleshooting
TROUBLESHOOTING TAKING CARE OF YOUR RECHARGEABLE BATTERIES • Ensure that you fully charge your batteries for 9 hours before their first use. • To maintain maximum battery life it is recommended that you fully discharge your batteries periodically. If your Parent Unit is not in use, please turn it OFF. FALSE ALARMS •... -
Page 18: Limited Warranty
This warranty does not cover products and product that Angelcare ® video, movement and sound accessories which are not Angelcare-branded, or monitor (model ) is free from any material any problems that result from usage that is not in and workmanship defects, for a period of accordance with product instructions, failure to year from the date of the original purchase. -
Page 19: Français
www.angelcarebaby.com...