Page 1
Shanghai Baudcom Communication Device Co.,Ltd BD-FS-30 Optical Fiber Fusion Splicer User Manual Version 1.00 Warning: Ignore the warning, non-proper use of fusion splicer could lead to fatal and serious injury. 1. The input voltage of this model of machine is definite; please do not use the voltage outside the scope.
Page 2
Shanghai Baudcom Communication Device Co.,Ltd ★ Smoke, smell, noise or heat anomaly ★ Broken or damaged machines ★ Liquid or foreign matter enters the interior of the machine 3. This model of fusion splicer does not have the need to maintain internal components, dismantling of fusion splicer and power modules is prohibited;...
Shanghai Baudcom Communication Device Co.,Ltd Content 1. Brief Introduction ......................1 1.1 Specifications ......................1 1.2 Configuration of fusion splicer ................1 1.3 Parts Name of fusion splicer ..................2 1. 4 Descriptions of the Keyboard .................. 3 2. Basic operation ......................4 2.1 Descriptions of the power modules ...............
0-5000m above sea level, Temperature: -10-60 , Humidity:0~95%RH (No dew) Weight (including battery) 1.98 KG (including battery) Dimension (LxWxH) 135mm(L)×158mm(W)×155mm(H) 1.2 Configuration of fusion splicer Following is the standard configurations of fusion splicer: Name Quantity Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
1 pc Cooling tray 1 pair Spare Electrodes 1 pc User Manual CD 1 pc Test Report 1.3 Parts Name of fusion splicer Windshield cover Heater Power switch Key board Power Module Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
To enter the next menu interface/ Invalid parameter files” menu parameter files” menu confirm the modifier Invalid Invalid Invalid Exit from the current menu screen Heater switch Heater switch Heater switch Heater switch Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
2.2 AC operation 2.2.1 When AC power supply is adopted, the AC/DC adapter supplied by the company should be used. The basic parameters of the adapter are as follows: INPUT: AC100-240V~1.8A 50/60HZ Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
Then the four battery capacity indicator (red) lights on the left side will be bright. The number of the lit light represents the highness or lowness of the battery capacity. See the following table. Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
Page 9
This model of fusion splicer has the function of “Under Voltage Alarm”. If the capacity of the lithium battery is lower than the specified value (the default value is around 10.3V), the splicer will automatically alarm and Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
Page 10
Accidents may happen if charging or discharging the battery or special battery charger and battery in a high temperature. <6>When charging the battery with the special battery charger, Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
. When all of the motors return to the initial position, the screen shows the reset menu. Turn off Press button on the operator panel until the LED indicator turn from Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
When the display brightness is moderate, the capacity loss can be reduced, and the endurance of the battery can be prolonged. 2.6 Cover fiber protection sleeve The installation of fiber protection sleeve Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
2.7.4 Close the small clip, big clip by right hand and promote sliding plate Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
2.8.1 Open shielding cover and left and right fiber clips. 2.8.2 Put the good fiber end face in the V-shaped groove; ensure the tip of the fiber between the tip of the electrode and V-shaped groove’s edge. Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
V-grooves do the following: <1> Open the wind protector. <2> Clean the bottom of the V-groove With an alcohol-impregnated thin cotton swab. Remove excess alcohol from the V-groove with a clean dry swab. Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
To clean the mirrors, do the following: Clean the mirror surface with an alcohol-impregnated thin cotton swab. Remove excess alcohol from the mirror surface with a clean dry swab. Mirror should look clean with no streaks or smudges. Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
<3> Turn on the power and make sure no smudges or streaks are visible on the monitor screen. Press X/Y to change the screen and check the state of Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
<3> Clean the new electrodes with alcohol-impregnated clean gauze or lint-free tissue and install them in the splicer. <4> Place the electrode cover and tighten screw ● Do not pull out night light wiring when replacing electrode. Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
4. 1 Open the cover of the battery case Lean the Fusion Splicer; open the cover of the battery case which is at the bottom of the Fusion Splicer. See the following picture: Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
Power does not turn off when pressing Press and hold the key until the LED color changes from red to green. Release to shut off the machine. Few splices can be made with a fully charged battery pack Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
Page 21
The battery pack has a fault or has reached the end of its service life. ● Install a new battery pack. If the LED blinks again after install, contact your nearest sales agency. The AC/DC adapter is not the model supplied by the Company. ● Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
Discharge calibration is needed only arc power fluctuates strongly; Note:* it is not necessary upon boot every time. After discharge calibration is completed, the machine will adjust the arc discharge Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
Page 23
4. Remove the tube from the heater when the heater is cool. The whole process of Fusion Operation is completed. Ⅴ. Repeat Step II, III, IV to continue splicing. Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...
What problems did your splicer get into and when? ● What is its present operational state? ● The state of the monitor and the contents of the relevant error message and etc. Website: www.baudcom.com.cn Tel: +86 21 37709251 Email: info@baudcom.com.cn...