Table of Contents
Advertisement
2)
Press the <ENTER> button.
f The [FRAME SYNC SETTING] screen is displayed.
3)
Press as to select [FRAME SYNC].
4)
Press qw to switch the item.
f The items will switch each time you press the button.
[OFF]
[MASTER]
[SLAVE]
f When anything other than [OFF] is selected, proceed to Step 5).
The usage of the <FRAME SYNC 1 IN/OUT> terminal and the <FRAME SYNC 2 OUT> terminal is
displayed in [FRAME SYNC1] and [FRAME SYNC2] in the [FRAME SYNC SETTING] screen.
The contents that are displayed are as follows.
[FRAME SYNC]
[MASTER]
[SLAVE]
5)
Press as to select [CONTRAST SYNC].
6)
Press qw to switch the item.
f The items will switch each time you press the button.
[OFF]
[ON]
f When [ON] is selected, the usage of the <FRAME SYNC 1 IN/OUT> terminal displayed in [FRAME SYNC1]
is switched.
The contents that are displayed are as follows.
[FRAME SYNC]
[MASTER]
[SLAVE]
f When [ON] is selected, the diagnosis result if the target projector is correctly connected is displayed in
[STATUS].
[ACTIVE]
[INACTIVE]
Note
f The [CONTRAST SYNC] function will operate when all of the following conditions are fulfilled.
g [FRAME SYNC] is set to [MASTER] on only the one projector to be linked, and it is set to [SLAVE] on all other projectors.
Chapter 4 Settings — [DISPLAY OPTION] menu
Select this item when the frames are not to be synchronized.
Select this item when the frames are to be synchronized.
Set this item in the one projector that is to be the synchronization source.
Select this item when the frames are to be synchronized.
Set this item in all the projectors that are to be the synchronization target.
[FRAME SYNC1]
[OUTPUT] is displayed.
The <FRAME SYNC 1 IN/OUT> terminal will
operate as an output terminal.
Connect to the <FRAME SYNC 1 IN/OUT>
terminal of the projector that is to be the
synchronization target.
[INPUT] is displayed.
The <FRAME SYNC 1 IN/OUT> terminal will
operate as an input terminal.
Select this item when the contrast is not balanced in the combined screen.
Select this item when the contrast is balanced in the combined screen.
The synchronization source projector with [FRAME SYNC] set to [MASTER] will calculate the
brightness level of the video signal to become optimum on the whole combined screen for every
frame. All the projectors targeted to link will control the dynamic contrast function based on the
calculation result.
[FRAME SYNC1]
[INPUT] is displayed.
The <FRAME SYNC 1 IN/OUT> terminal will
operate as an input terminal.
Connect to the <FRAME SYNC 2 OUT> terminal
of the last projector.
[INPUT] is displayed.
The <FRAME SYNC 1 IN/OUT> terminal will
operate as an input terminal.
The target projector is correctly connected and the [CONTRAST SYNC] function is operating.
The [CONTRAST SYNC] function is stopped. Confirm the setting of each linked projector and the
connection of the cable.
[FRAME SYNC2]
[OUTPUT] is displayed.
The <FRAME SYNC 2 OUT> terminal will operate
as an output terminal.
Connect to the <FRAME SYNC 1 IN/OUT>
terminal of the projector that is to be the
synchronization target.
[OUTPUT] is displayed.
The <FRAME SYNC 2 OUT> terminal will operate
as an output terminal.
[FRAME SYNC2]
[OUTPUT] is displayed.
The <FRAME SYNC 2 OUT> terminal will operate
as an output terminal.
Connect to the <FRAME SYNC 1 IN/OUT>
terminal of the first projector that is to be the
synchronization target.
[OUTPUT] is displayed.
The <FRAME SYNC 2 OUT> terminal will operate
as an output terminal.
ENGLISH - 119
Advertisement
Table of Contents
