Related Manuals for Eneo MPD-62M2812P0A
Summary of Contents for Eneo MPD-62M2812P0A
- Page 1 User Manual 1/2.8” HD Dome, Fixed, WDR, Day&Night, 1920x1080, 12V, Infrared, 2.8-12mm, Indoor MPD-62M2812P0A...
-
Page 3: Safety Precaution
MPD-62M2812P0A Safety Precaution To prevent fire or shock hazard, do not expose the unit to rain or moisture. To prevent electric shocks and risk of fire hazards, do NOT use other than specific power source. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). - Page 4 MPD-62M2812P0A Safety Precaution NOTICE The image used in this instruction manual are processed to help comprehension and may differ from actual video of the camera. Avoid installing areas where has shock or vibration which results in the problems. Pay attention to safety when laying the connection cable and observe that the cable is not subjected to heavy loads, kinks or damage and no moisture can get in.
-
Page 5: Table Of Contents
MPD-62M2812P0A Contents p.03~04 Safety Precaution p.05 Contents p.06 Features p.07 Composition p.08 Dimensions p.09 Part Names p.10~12 Installation Instructions p.13~29 Operating Instructions p.30 Specifications... -
Page 6: Features
MPD-62M2812P0A Features Key Features • Full-HD 2Mega pixel CAMERA, 1920x1080(30p/25p) • The best low light performance with SONY’s STARVIS sensor • Video output EX-SDI 1.0,2.0 / HD-SDI / TVI mode / AHD mode / CVI mode or CVBS Selectable • TVI mode / AHD mode / CVI mode, Video Transmission Distance over Coax.;... -
Page 7: Composition
MPD-62M2812P0A Composition Mounting Template Operating Instruction Dome Camera Plastic Anchor: 6 x 30mm (3pcs) Mounting Screw: 3.5 x 25mm (3pcs) Easy Adaptor (Flat type) Open Driver (1pc) Easy Adaptor Video Sub-out Cable (Tilted type) -
Page 8: Dimensions
MPD-62M2812P0A Dimensions (unit : mm) Tilted Adaptor CAUTION • Extreme care should be taken NOT to scratch the bubble dome surface while the camera installing or adjusting. • Care should be taken the cable is NOT to be damaged, kinked or exposed in the hazardous area. -
Page 9: Part Names
MPD-62M2812P0A Part Names Tilted Easy Adaptor Power/Video Cable Easy Adaptor Flat type Dome Base Lens 3-Axis Gimbal OSD Menu Control board Dome Cover Light Bubble Shield Sensor Bubble SMD LEDs... -
Page 10: Installation Instructions
MPD-62M2812P0A Installation Instructions 1. Drill three holes for mounting on the ceiling or wall. 2. Place the Easy Adaptors at the pre-drilled installation position and fix it by using mounting screws. 3. Route the power/video cable to the connecting place. - Page 11 MPD-62M2812P0A Installation Instructions Limit of pan & tilt 1) Pan limit: Pan is limited to +/- 165°. ■ EXTENDED VIEWING ANGLE Do NOT force to rotate the gimbal over the limit to prevent from the internal damage. 2) Tilt limit: Tilt is limited to 25°...
- Page 12 MPD-62M2812P0A Installation Instructions ■ Open the dome cover ① Insert wide side of Open Tool into the lock of Dome Cover. ② Hold the Dome housing with one hand and turn the open tool until Dome Cover is sufficiently open.
-
Page 13: Operating Instructions
MPD-62M2812P0A Operating Instructions Using OSD Controller Setup menu can be accessed and controlled by OSD control joy stick on the side of the gimbal. Five commands are available with the joy stick. The design of OSD could be different according to the Model. - Page 14 MPD-62M2812P0A Operating Instructions OSD menu Table MENU SUB MENU CONFIGURATION LENS MODE (INDOOOR, OUTDOOR, DEBLUR) MANUAL ZOOM / FOCUS AF MODE ZOOMPUSH, MANUAL MODE CHANGE ENABLED, DISABLED SCANNING HALF, FULL ONEPUSHAF SYNC TDN ON, OFF INITIAL 0~20 EXPOSURE BRIGHTNESS SHUTTER...
- Page 15 MPD-62M2812P0A Operating Instructions IMAGE SHARPNESS MAIN ANALOG ANALOG CVBS OUTPUT OUT1 OUT1 SDI&CVBS 0~10 SDI OUT HD-SDI, EX-SDI 1.0, OUTPUT EX-SDI 2.0, OFF SDI&CVBS 0~10 GAMMA 0.45, 0.55, 0.65, 0.75 MIRROR OFF, ON FLIP OFF, ON OFF, LOW, MIDDLE, HIGH...
- Page 16 MPD-62M2812P0A Operating Instructions OSD menu Startup Press the ‘OSD menu SET key’ down to access the setup menu mode. • EXIT : Enters ‘EXIT’ menu with save current setting or without save. • RETURN : Returns to the previous menu.
- Page 17 MPD-62M2812P0A Operating Instructions 2. ZOOM/FOCUS 2. ZOOM/FOCUS AF MODE AF MODE ZOOMPUSH MANUAL MODE CHANGE MODE CHANGE DISABLED NOT USED SCANNING SCANNING HALF HALF ONEPUSHAF ONEPUSHAF SYNC TDN SYNC TDN INITIAL INITIAL RETURN RETURN AF MODE Changes to MANUAL automatically after 3 hrs when MODE CHANGE is ENABLED.
- Page 18 MPD-62M2812P0A Operating Instructions 3. EXPOSURE 3. EXPOSURE BRIGHTNESS llllllllllllllllllllll SHUTTER AUTO SENS-UP llllllllllllllllllllll RETURN 3-1. BRIGHTNESS Adjusts the brightness of video (0~20). 3-2. SHUTTER Selects AUTO or set manually. If SHUTTER set to MANUAL modes, SENS-UP mode is inactivated. 3-2-1. AUTO: Optimizes the video level by controlling the iris and the shutter speed automatically.
- Page 19 MPD-62M2812P0A Operating Instructions 4. BACKLIGHT Compensates the video image to cut out the highlight area with mask or control the contrast of video. It can be set the compendation level or areas. LEVEL llllllllllllllllllllll COLOR RETURN 4-1. HLC (High Light Compensation) Cuts out the highlight area with mask and excludes it from compensation.
- Page 20 MPD-62M2812P0A Operating Instructions MODE WINDOW ZONE WEIGHT WINDOW USE MIDDLE RETURN H-POS V-POS H-SIZE V-SIZE RETURN 4-3. WDR (Wide Dynamic Range) WDR is extended the gain range of the video that is mostly useful if camera takes a simultaneous picture of both indoor and outdoor nearby window.
- Page 21 MPD-62M2812P0A Operating Instructions 5. DAY & NIGHT DAY/NIGHT is used to control the setting during day-time and night-time operation. Select the mode according to the light condition and the camera types. MENU V0. XX 1. LENS 5. DAY&NIGHT 2. ZOOM/FOCUS 3.
- Page 22 MPD-62M2812P0A Operating Instructions 5-2. AUTO Used when DAY or NIGHT is 5. DAY&NIGHT determined by light level through the lens and DAY from/to NIGHT SMART IR is switched automatically by the ANTI-SAT. llllllllllllllllllllll scene brightness. AGC THRES llllllllllllllllllllll It can be controlled the AGC...
- Page 23 MPD-62M2812P0A Operating Instructions 6. COLOR 6. COLOR AUTO COLOR GAIN llllllllllllllllllllll RETURN 6-1. AWB (Auto White Balance) Automatically tracks the changes of color temperature and continuously adjusts the white balance. AUTO, AUTOext, PRESET and MANUAL modes are available. 6-1-1. AUTO : Optimized for Indoor installation and more easily compensates AWB for low color temperature such as incandescent lights.
- Page 24 MPD-62M2812P0A Operating Instructions 7. 3D-NR (Digital Noise Reduction) DNR function improves picture quality by filtering out signal noise which is generated under the low light conditions. Sets off, low, middle or high level. 3DNR(3-dimensional noise reduction) which reduces the noise by the multi frames.
- Page 25 MPD-62M2812P0A Operating Instructions 8-1. SHARPNESS Sets the Sharpness level 0~10. Increases or decreases the sharpness of the picture. Too much sharpness can make image harsh and show more noise as well as line flicker at the edge of object in the picture.
- Page 26 MPD-62M2812P0A Operating Instructions PRIVACY ZONE NUM ZONE DISP H-POS V-POS H-SIZE V-SIZE Y-LEVEL llllllllllllllllllllll CB LEVEL llllllllllllllllllllll CR LEVEL llllllllllllllllllllll TRANS RETURN 8-7-4. H-SIZE, V-SIZE : Adjusts the mask size using H, V direction which you selected zone. 8-7-5. Y LEVEL : Adjusts the mask color by Y LEVEL. (0: black ~ 20: white) 8-7-6.
- Page 27 MPD-62M2812P0A Operating Instructions 9. MOTION DET WINDOW DET WINDOW WINDOW ZONE DET TONE WINDOW USE MDRECT FILL DET H-POS SENSITIVITY llllllllllllllllllllll DET V-POS MOTION OSD DET H-SIZE TEXT ALARM DET V-SIZE RETURN RETURN 9-2. DET TONE Sets the detection zone 0 to 4 display types which window use setting ON.
- Page 28 MPD-62M2812P0A Operating Instructions A. SYSTEM Sets the system related functions. A. SYSTEM OUTPUT RESOLUTION 1080 25P TV SYSTEM EU(PAL) LANGUAGE CAM TITLE RESET RETURN HD-ANALOG OUTPUT MAIN OUTPUT ANALOG OUT0 TVI MODE ANALOG OUT0 HD-SDI SDI OUTPUT Y GAIN llllllllllllllllllllll...
- Page 29 MPD-62M2812P0A Operating Instructions If CVBS video is enabled through ANALOG OUT0 or Sub-out port, WDR and 3D-NR functions are disabled in all video outputs. It should be considered when installer adjusts the video with installation monitor via CVBS video signal.
-
Page 30: Specifications
MPD-62M2812P0A Specifications ITEM MPD-62M2812P0A Imaging Sensor 1/2.8" Sony 2Mega pixel STARVIS CMOS Sensor Effective Pixels 1920(H) x 1080(V) x 25p Scan Frequency 25Hz(V), 18.75Khz(H) / Progressive Video Format HD] 16:9, 1080p@25fps CVBS] 16:9 (PAL) Synchronization Internal Video Output EX-SDI1.0, 2.0 /HD-SDI / TVI mode/ AHD mode/ CVI mode/ CVBS Video Resolution 1920x1080 (30p/25p) Min.Illumination... - Page 32 Videor E. Hartig GmbH Exclusive distribution through special- ised trade channels only. Videor E. Hartig GmbH Carl-Zeiss-Straße 8 63322 Rödermark/Germany Tel. +49 (0) 6074 / 888-0 Technical changes reserved Fax +49 (0) 6074 / 888-100 www.videor.com...