Receiver Controls; Remote Control - Dimplex CAS500R Manual

CAS1000R
Mains Switch - Controls the electricity supply to the appliance. (Fig 26A)
Note: This switch must be in the 'ON' ( I ) position for the appliance to operate
Button Panel 'C' Controls the functioning of the left side of product while Button Panel 'D' controls the functioning of the
right side of the product. Please note the flame height and fire crackling noise can be controlled independently on each
individual side of the product.
• is the on/standby button. Press it to turn on and off the flame effect. Turning it on will be indicated by a single
beep and the main LED lights activating. Be careful not to look directly into the LED's as they can be very bright.
Although the main LED lights operate immediately, a further 45 seconds of warm up time is required before the
flame effect starts.
• is the pairing button. This will pair your remote control to the receiver. See 'Remote Control Operation' for details.
• is the test mode button. This will be used by the manufacturer and the Service Engineer.
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level.
• is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off. You will hear an audible beep when you reach the minimum level.
• is the increase fire crackling sound. Press this to increase the volume of the crackling sound. You will hear an
audible beep when you reach the maximum level.

RECEIVER CONTROLS

The product can also be controlled using the receiver which is supplied with the product. (Fig 11)
CAS500R
• is the on/standby button. Press it to turn on and off the flame effect.
• is used to mute the fire crackling sound. Press this to turn on and off the crackling sound. The volume can be
adjusted on the manual controls of the appliance. Please note that the mute setting will not be saved after a product
restart. The crackling sound can be turned off completely by using the volume control buttons on the button panel to
reduce the volume to its minimum setting. This minimum setting will be remembered after a product restart.
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level.
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level
CAS1000R
• is the on/standby button. Press it to turn on and off the flame effect.
• is used to mute the fire crackling sound. Press this to turn on and off the crackling sound. The volume can be
adjusted on the manual controls of the appliance. Please note that the mute setting will not be saved after a product
restart. The crackling sound can be turned off completely by using the volume control buttons on the button panel to
reduce the volume to its minimum setting. This minimum setting will be remembered after a product restart.
• is the reduce flame button. Press the reduce flame button on the second button row to reduce the height/intensity
of the flame on the left hand side of the product. Press the reduce flame button on the third button row to reduce
the height/intensity of the flame on the right hand side of the product. You will hear an audible beep when you reach
the minimum level.
• is the increase flame button. Press the increase flame button on the second button row to increase the height/
intensity of the flame on the left hand side of the product. Press the increase flame button on the third button row to
increase the height/intensity of the flame on the right hand side of the product. You will hear an audible beep when
you reach the maximum level.

REMOTE CONTROL

The remote control is supplied with 2xAAA batteries. Remove the battery cover from the underside of the remote control
and after removing the batteries from the plastic wrapping fit them into place. Replace the battery cover. With the product
powered off, a functional test can be carried out on the remote control by pushing any button and observing the blue LED
at the top o the remote flashing with each button push.
Pairing the Remote Control
The remote control has wireless Bluetooth technology and needs to be paired to the receiver. This can be done by
following the steps below.
1. Press the rocker switch to the on (I) position; a single beep will be heard.
2. Press the button on the Button Panel; the product will turn on.
5