Receiver Controls; Remote Control - Dimplex CAS500R Manual

RECEIVER CONTROLS

The product can also be controlled using the receiver which is supplied with the product. (Fig 12)
CAS500R
• is the on/standby button. Press it to turn on and off the flame effect.
• is used to mute the fire crackling sound. Press this to turn on and off the crackling sound. The volume can be
adjusted on the manual controls of the appliance. Please note that the mute setting will not be saved after a product
restart. The crackling sound can be turned off completely by using the volume control buttons on the button panel to
reduce the volume to its minimum setting. This minimum setting will be remembered after a product restart.
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level.
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level
CAS1000R
• is the on/standby button. Press it to turn on and off the flame effect.
• is used to mute the fire crackling sound. Press this to turn on and off the crackling sound. The volume can be
adjusted on the manual controls of the appliance. Please note that the mute setting will not be saved after a product
restart. The crackling sound can be turned off completely by using the volume control buttons on the button panel to
reduce the volume to its minimum setting. This minimum setting will be remembered after a product restart.
• is the reduce flame button. Press the reduce flame button on the second button row to reduce the height/intensity
of the flame on the left hand side of the product. Press the reduce flame button on the third button row to reduce
the height/intensity of the flame on the right hand side of the product. You will hear an audible beep when you reach
the minimum level.
• is the increase flame button. Press the increase flame button on the second button row to increase the height/
intensity of the flame on the left hand side of the product. Press the increase flame button on the third button row to
increase the height/intensity of the flame on the right hand side of the product. You will hear an audible beep when
you reach the maximum level.

REMOTE CONTROL

The remote control is supplied with 2xAAA batteries. Remove the battery cover from the underside of the remote control
and after removing the batteries from the plastic wrapping fit them into place. Replace the battery cover. With the product
powered off, a functional test can be carried out on the remote control by pushing any button and observing the blue LED
at the top o the remote flashing with each button push.
Pairing the Remote Control
The remote control has wireless Bluetooth technology and needs to be paired to the receiver. This can be done by
following the steps below.
1. Press the rocker switch to the on (I) position; a single beep will be heard.
2. Press the button on the Button Panel; the product will turn on.
3. Press the button on the Button Panel, the LED's will start to slowly blink on and off.
4. Press the button on the remote control; the product LEDs will flash quickly three times and the product will then
automatically switch off. The remote control is now paired to the product and can be used to switch it back on.
The operation of the remote control is the same as described in 'Receiver Controls'. You can pair multiple products to the
one remote control by repeating the pairing operation as above on your subsequent products. Please note a maximum
of six CAS500R/CAS1000R products can be paired to the one remote control.
Pairing the Remote Control to Multiple Products
If you are installing multiple CAS500R/CAS1000R products you can pair them to a single remote control. To do this,
please install the products as described in the "Installation Instructions". Ensure that all products are connected to mains
power and have water supplied. If you are pairing CAS1000R and CAS500R products please choose the 6 button
remote control as the master remote control.
1. Pair the first product as described in steps 1-4 above.
2. On your second product, press the rocker switch to the on (I) position; a single beep will be heard.
3. Press the button on the Button Panel; the product will turn on.
4. Press the button on the Button Panel, the LED's will start to slowly blink on and off.
5. Press the button on the remote control; the LEDs will flash quickly three times and the product will then
automatically switch off. The remote control is now paired to the two products and can be used to switch them on.
6. Repeat the above steps to pair the next product.
5