Daikin Altherma 3 H HT F Installer's Reference Manual page 294

10/13
Field settings table
Breadcrumb Field code Setting name
9.I [5-08] What is the requested limit for DI4?
9.I [5-09] What is the requested limit for DI1?
9.I [5-0A] What is the requested limit for DI2?
9.I [5-0B] What is the requested limit for DI3?
9.I [5-0C] What is the requested limit for DI4?
9.I [5-0D] Backup heater voltage
9.I [5-0E] --
9.I [6-00] The temperature difference determining the heat pump ON temperature.
9.I [6-01] The temperature difference determining the heat pump OFF temperature.
9.I [6-02] What is the capacity of the booster heater?
9.I [6-03] What is the capacity of the backup heater step 1?
9.I [6-04] What is the capacity of the backup heater step 2?
9.I [6-07] --
9.I [6-08] What is the hysteresis to be used in reheat mode?
9.I [6-09] --
9.I [6-0A] What is the desired comfort storage temperature?
9.I [6-0B] What is the desired eco storage temperature?
9.I [6-0C] What is the desired reheat temperature?
9.I [6-0D] What is the desired DHW production type?
9.I [6-0E] What is the maximum temperature setpoint?
9.I [7-00] Domestic hot water booster heater overshoot temperature.
9.I [7-01] Domestic hot water booster heater hysteresis.
9.I [7-02] How many leaving water temperature zones are there?
9.I [7-03] --
9.I [7-04] --
9.I [7-05] Boiler efficiency
9.I [7-06] Compressor forced OFF
9.I [7-07] BBR16 activation*
*BBR16 settings are only visible when the language of the user interface is set to
Swedish
9.I [7-08] --
9.I [7-09] --
9.I [7-0A] Additional zone fixed pump PWM, in case a bizone kit is installed.
9.I [7-0B] Main zone fixed pump PWM, in case a bizone kit is installed.
9.I [7-0C] Time needed by the mixing valve to turn from one side to the other, in case a
bizone kit is installed.
9.I [8-00] Minimum running time for domestic hot water operation.
9.I [8-01] Maximum running time for domestic hot water operation.
9.I [8-02] Anti-recycling time.
9.I [8-03] Booster heater delay timer.
9.I [8-04] Additional running time for the maximum running time.
9.I [8-05] Allow modulation of the LWT to control the room temp?
9.I [8-06] Leaving water temperature maximum modulation.
9.I [8-07] What is the desired comfort main LWT in cooling?
9.I [8-08] What is the desired eco main LWT in cooling?
9.I [8-09] What is the desired comfort main LWT in heating?
9.I [8-0A] What is the desired eco main LWT in heating?
9.I [8-0B] --
4P644734-1A - 2022.03
Range, step
Default value
R/W 0~50 A, step: 1 A
50 A
R/W 0~20 kW, step: 0,5 kW
20 kW
R/W 0~20 kW, step: 0,5 kW
20 kW
R/W 0~20 kW, step: 0,5 kW
20 kW
R/W 0~20 kW, step: 0,5 kW
20 kW
R/W (*1) 0: 230V, 1~ (*1)
R/O (*2)
1: 230V, 3~ (*1)
2: 400V, 3~ (*2)
1
R/W 2~40°C, step: 1°C
8°C
R/W 0~10°C, step: 1°C
2°C
R/W 0~10kW, step: 0,2kW
3kW (*3)
0kW (*4)
R/W 0~10kW, step: 0,2kW
2kW (*1)
3kW (*2)
R/W 0~10kW, step: 0,2kW
4kW (*1)
6kW (*2)
0
R/W 2~20°C, step: 1°C
10°C
0
R/W 30~[6-0E]°C, step: 1°C
60°C
R/W 30~min(50, [6-0E])°C, step: 1°C
45°C
R/W 30~min(50, [6-0E])°C, step: 1°C
45°C
R/W 0: Reheat only
1: Reheat + sched.
2: Scheduled only
R/W (*3) [E-07]=0 or 7:
40~ 60°C, step: 1°C
60°C
(*3) [E-07]=3 or 5 or 8:
40~80°C, step: 1°C
80°C
(*4) : 40~65°C, step: 1°C
65°C
R/W 0~4°C, step: 1°C
0°C
R/W 2~40°C, step: 1°C
2°C
R/W
0: 1 LWT zone
1: 2 LWT zones
2.5
0
R/W 0: Very high
1: High
2: Medium
3: Low
4: Very low
R/W 0: Disabled
1: Enabled
R/W 0: Disabled
1: Enabled
0
20
R/W 20~95%, step 5%
95%
R/W 20~95%, step 5%
95%
R/W 20~300 seconds, step 5 sec
125 seconds
R/W 0~20 min, step 1 min
1 min
R/W 5~95 min, step: 5 min
30 min
R/W 0~10 hour, step: 0,5 hour
0,5 hour [E-07]=1
3 hour [E-07]≠1
R/W 20~95 min, step: 5 min
50 min
R/W 0~95 min, step: 5 min
95 min
R/W 0: No
1: Yes
R/W 0~10°C, step: 1°C
5°C
R/W [9-03]~[9-02], step: 1°C
18°C
R/W [9-03]~[9-02], step: 1°C
20°C
R/W [9-01]~[9-00], step: 1°C
35°C
R/W [9-01]~[9-00], step: 1°C
33°C
13
Installer setting at variance with
default value
Date Value
(*1) *6V*_(*2) *9W*_
(*3) ETB*_(*4) ETV*_
(*5) *X*_(*6) *H*_(*7) *SU*_
(*8) E_(*9) E7