Daikin Altherma 3 H HT F Installation Manual

Daikin Altherma 3 H HT F Installation Manual

Hide thumbs Also See for Altherma 3 H HT F:
Table of Contents

Advertisement

Quick Links

Installation manual
Daikin Altherma 3 H HT F
https://daikintechnicaldatahub.eu
Installation manual
ETVH16SU18EA6V
English
Daikin Altherma 3 H HT F
ETVH16SU23EA6V

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Altherma 3 H HT F and is the answer not in the manual?

Questions and answers

Summary of Contents for Daikin Altherma 3 H HT F

  • Page 1 Installation manual Daikin Altherma 3 H HT F https://daikintechnicaldatahub.eu Installation manual ETVH16SU18EA6V English Daikin Altherma 3 H HT F ETVH16SU23EA6V...
  • Page 2 3P644742-3...
  • Page 3: Table Of Contents

    Configuration wizard: Time and date ......24 7.2.3 Configuration wizard: System ........24 7.2.4 Configuration wizard: Backup heater ......25 7.2.5 Configuration wizard: Main zone......... 26 7.2.6 Configuration wizard: Additional zone......26 ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 4: Specific Installer Safety Instructions

    ▪ Discharge piping, tundish, drain valves, etc. must be Daikin website (publicly accessible). positioned away from any electrical components. ▪ The full set of latest technical data is available on the Daikin ▪ The discharge pipe away from the tundish must Business Portal (authentication required).
  • Page 5: About The Box

    Tundish (to mount onto the pressure relief valve discharge pipe) DANGER: RISK OF BURNING/SCALDING Brass compression coupler Discharge pipe (for pressure relief valve) The water in the tank can be very hot. General safety precautions ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 6: To Handle The Indoor Unit

    Please contact your dealer if you have no access to Heating Solutions Navigator. NOTICE All piping MUST be installed according to section G3 of the Building Regulations. Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 7: Opening And Closing The Unit

    NOTICE If you remove the user interface panel, also disconnect the cables from the back of the user interface panel to prevent damage. ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 8: To Lower The Switch Box On The Indoor Unit

    Prerequisite: The user interface panel and front panel have been removed. 1 Remove one of the side panels. 2 Cut out the rubber grommet. 3 Pull the drain hose through the hole. Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 9: Piping Installation

    (check that the user interface does NOT display error to ensure that the maximum pressure is NOT exceeded. The 7H). minimum water pressure to operate is 1 bar. ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 10: Connecting Water Piping

    These shut-off valves are field supplied. Pressure reducing valve/pressure relief valve combination. Water inlet and water outlet 22 mm connection, discharge piping connection 15 mm Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 11 The following example shows discharge below fixed grating (Building Regulation G3 section 3.61 gives alternative points of discharge): ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 12: To Connect The Recirculation Piping

    To prevent the system However, in case of a power failure, these functions cannot guarantee protection. from freezing, more glycol is required. Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 13: To Fill The Domestic Hot Water Tank

    If lower, freeze protection valves can open during cooling operation. For more information, see the installer reference guide. ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 14: Connections To The Indoor Unit

    ▪ Installation manual of the wired room ▪ [2.A] Thermostat type without multi-zoning base thermostat For the additional zone: unit ▪ Addendum book optional ▪ [3.A] Thermostat type equipment ▪ [3.9] (read-only) Control Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 15: To Connect The Main Power Supply

    OR ▪ if no power consumption of the indoor unit is allowed at Interconnection cable (=main power supply) the preferential kWh rate power supply when active. ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 16: To Connect The Backup Heater Power Supply

    Factory-mounted cable connected to the contactor of the backup heater, inside the switch box (K5M) Do NOT cut or remove the backup heater power supply Field wiring (see table below) cable. Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 17: To Connect The Shut-Off Valve

    21 28 3 Fix the cable with cable ties to the cable tie mountings. 21 29 3 Fix the cable with cable ties to the cable tie mountings. ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 18: To Connect The Domestic Hot Water Pump

    3 Upper switch box cover 2 User interface panel 3 Upper switch box cover 2 Connect the alarm output cable to the appropriate terminals as shown in the illustration below. Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 19: To Connect The Changeover To External Heat Source

    [9.C] Bivalent unit" [ 4  7]): 1 Open the following (see "4.2.1 To open the indoor 1 Top panel 2 User interface panel 3 Upper switch box cover ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 20: To Connect The Safety Thermostat (Normally Closed Contact)

    The 2 incoming Smart Grid contacts can activate the following Smart respective terminals. Grid modes: Smart Grid contact Smart Grid operation mode Free running Forced off Recommended on Forced on Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 21 Screws for K1A and K2A Sticker to put on the high voltage wires Wires between the relays and X5M (AWG22 ORG) Wires between the relays and X10M (AWG18 RED) ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 22: To Connect The Wlan Cartridge (Delivered As Accessory)

    This chapter describes what you have to do and know to configure the system after it is installed. High voltage Smart Grid contact 1 High voltage Smart Grid contact 2 Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 23: To Access The Most Used Commands

    ▪ Browse through the list of digits and change the selected digit. ▪ Move the cursor from left to right. ▪ Confirm the pin code and proceed. ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 24: Configuration Wizard

    This setting is read only. main LWT zone. Code Description [9.2.1] [E‑05] ▪ Integrated [E‑06] The backup heater will also be used for domestic hot water heating. [E‑07] Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 25: Configuration Wizard: Backup Heater

    50°C, Glycol Filled system Daikin recommends NOT to disable the backup heater second step because it will have a big impact on the This setting gives the installer the possibility to indicate whether the required time for the unit to heat up the domestic hot water system is filled with glycol or water.
  • Page 26: Configuration Wizard: Main Zone

    ▪ Enable leaving water temperature modulation and Emitter type increase the maximum modulation [2.C]. For more info about this functionality, see "7.2.5  Configuration zone" [ 4  26]. wizard: Main Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 27: Configuration Wizard: Tank

    Because the slope of the curve depends on local circumstances such as climate and the insulation of the house, the curve can be adjusted by an installer or user. ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 28: 2-Points Curve

    Possible actions on this screen X1, X2 Examples of outdoor ambient temperature Go through the temperatures. Change the temperature. Go to the next temperature. Confirm changes and proceed. Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 29: Using Weather-Dependent Curves

    ▪ [5.E] Tank > WD curve type — ↓ — ↓ Restriction: Only available to installers. Cold ↑ ↓ ↑ ↓ ↓ ↓ ↓ ↓ curve" [ 4  28]. "7.3.2 2-points ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 30: Settings Menu

    ▪ 2: 2 contacts 7.4.3 Information Dealer information The installer can fill in his contact number here. Code Description [8.3] Number that users can call in case of problems. Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 31: Menu Structure: Overview Installer Settings

    Solar kit settings are shown but are NOT applicable for this unit. Settings shall NOT be used or changed. INFORMATION Depending on the selected installer settings and unit type, settings will be visible/invisible. ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 32: Commissioning

    The power supply voltage matches the voltage on the commissioning checklist is also available on the Daikin identification label of the unit. Business Portal (authentication required). There are NO loose connections or damaged electrical The general commissioning checklist is complementary to components in the switch box.
  • Page 33: To Perform An Air Purge

    1 In the menu, go to Stop test run. ▪ [4‑01]≠1 2 Select OK to confirm. Possible actuator test runs ▪ Backup heater 1 test ▪ Backup heater 2 test ▪ Pump test ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 34: Hand-Over To The User

    ▪ Show the user what to do for the maintenance of the unit. ▪ Explain the user about energy saving tips as described in the operation manual. Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 35: 10 Maintenance And Service

    Open the valve and check if it operates correctly. The water may be very hot! Checkpoints are: ▪ The water flow coming from the relief valve is high enough, no blockage of the valve or in between piping is suspected. ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 36: To Drain The Domestic Hot Water Tank

    4  7]. 1 Remove the top panel. See "4.2.1 To open the indoor 2 Remove the user interface panel. See "4.2.1 To open the indoor unit" [ 4  7]. Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 37: To Inspect The Inside Of The Domestic Hot Water Tank

    6 Open the valve on the bottom of the water filter to drain water inspection (e.g. with an endoscope). from the water circuit. Collect the drained water in a bottle, sink, … using the installed drain hose. ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 38: To Clean The Water Filter In Case Of Trouble

    4 Install the cleaned rolled‑up filter and strainer in the water filter housing. INFORMATION Correctly install the strainer in the magnetic filter/dirt separator housing using the protrusions. Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 39: 11 Technical Data

    11 Technical data Technical data A subset of the latest technical data is available on the regional Daikin website (publicly accessible). The full set of latest technical data is available on the Daikin Business Portal (authentication required). 11.1 Piping diagram: Indoor unit...
  • Page 40: Wiring Diagram: Indoor Unit

     On/OFF thermostat (wireless)  On/OFF thermostat (wireless) X*, X*A, J*, X*H*, Connector  Ext. thermistor  External thermistor  Heat pump convector  Heat pump convector Terminal strip * Optional # Field supply Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 41 Smartgrid PV power pulse meter Smart Grid photovoltaic power pulse meter Switch box (7) Option PCBs (7) Option PCBs Alarm output Alarm output Changeover to ext. heat source Changeover to external heat source ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 42 4 core communication A3P: X11M: 3-4-5-6 signal main & add: X2M: 3-4 Only for Human Comfort Interface 2 core 2×0.75 X5M: 11-12 A14P: P1-P2 user interface communication 4D133216A Installation manual ETVH16SU18+23EA6V Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 43: Technical Specifications: Domestic Hot Water Tank

    ETVH16SU18EA6V 180 l 289 kg ETVH16SU23EA6V 220 l 338 kg 10 bar ■ Maximum design pressure: ■ Rated volume heat exchanger: 9.1 l 4P647876-1A ETVH16SU18+23EA6V Installation manual Daikin Altherma 3 H HT F 4P644729-1 – 2021.02...
  • Page 44 4P644729-1 0000000U 4P644729-1 2021.02 Verantwortung für Energie und Umwelt...

This manual is also suitable for:

Etvh16su18ea6vEtvh16su23ea6vEtvh16ue6v

Table of Contents