1. Manuals
  2. Brands
  3. ETAS Manuals
  4. Computer Hardware
  5. FETK-T4.0B
  6. User manual

ETAS FETK-T4.0B User Manual

Emulator probe for stm stellar sr6 mcu family
Hide thumbs Also See for FETK-T4.0B:
Table of Contents

Advertisement

Quick Links

Download this manual
ETAS FETK-T4.0B
Emulator Probe for STM STELLAR SR6
MCU Family
User Guide

Advertisement

Table of Contents
loading

Related Manuals for ETAS FETK-T4.0B

Summary of Contents for ETAS FETK-T4.0B

  • Page 1 ETAS FETK-T4.0B Emulator Probe for STM STELLAR SR6 MCU Family User Guide...
  • Page 2 The data in this document may not be altered or amended without special noti- fication from ETAS GmbH. ETAS GmbH undertakes no further obligation in relation to this document. The software described in it can only be used if the customer is in possession of a general license agreement or single license.

  • Page 3: Table Of Contents

    Trigger Modes ............27 FETK-T4.0B - User Guide...
  • Page 4 ETAS Compatible Hardware ........
  • Page 5 Ordering ............69 FETK-T4.0B - User Guide...
  • Page 6 FETK-T4.0B ........

  • Page 7: About This Document

    Presentation of Instructions The target to be achieved is defined in the heading. The necessary steps for his are in a step-by-step guide: Target definition 1. Step 1 2. Step 2 3. Step 3 > Result FETK-T4.0B - User Guide...

  • Page 8: Typographical Conventions

    General emphasis and new terms are set in dimensional table of sample italics. points. Hardware Bold Menu commands, buttons, labels of the product Italic Emphasis on content and newly introduced terms Presentation of Supporting Information NOTE Contains additional supporting information. FETK-T4.0B - User Guide...

  • Page 9: Basic Safety Notices

    Use of Open Source Software........15 General Safety Information Please observe the Product Safety Notices ("ETAS Safety Notice") and the fol- lowing safety notices to avoid health issues or damage to the device.
  • Page 10 Application Area of the Product This product was developed and approved for automotive applications. For use in other application areas, please contact your ETAS contact partner. Requirements for Operation The following requirements are necessary for safe operation of the product: •...
  • Page 11 CAUTION Risk of short circuiting the internal signals of the ETK! When you mount the ETK to the ECU, you must ensure that the screws and washers used will not penetrate the ETK printed circuit board. FETK-T4.0B - User Guide...
  • Page 12 Cabling Use exclusively ETAS cables at the connections of the product! Adhere to the maximum permissible cable lengths! Observe the assignment of the cables to the connectors! Detailed information about cabling is located in the ETK User Guides.

  • Page 13: Identifications On The Product

    XETK-S14.0A Product designation (example) F 00K 110 722 Order number of the product (example) SN: yyxxxxx Serial number (7-digit) XXXX/YY Product version ZZZZ Year of manufacture ETAS GmbH, Manufacturer's address PO Box 300220, 70442 Stuttgart, Germany FETK-T4.0B - User Guide...

  • Page 14: Taking The Product Back And Recycling

    2.6.1 CE Declaration of Conformity (European Union) With the CE mark attached to the product or its packaging, ETAS confirms that the product corresponds to the applicable product-specific European Direc- tives. The CE Declaration of Conformity for the product is available upon request.

  • Page 15: People's Republic Of China

    7A and 7C-I in Annex III of this Directive. ETAS confirms that the product corresponds to this directive which is applica- ble in the European Union.

  • Page 16: Introduction

    Trace Trigger By Value Trace Trigger By Reference To access the ECU the FETK-T4.0B has to be connected via ES89x modules. The system can be used for high speed Measurement, Calibration and ECU flash programming. Support of high speed and high band width applications e.g.

  • Page 17: Features

    – Pull CalWakeUp until Startup Handshake: duration of the Wake up mechanism is configurable ECU Flash Programming via FETK • Using microcontroller debug interface, ECU software support not neces- sary • Braindead flashing under ProF control FETK-T4.0B - User Guide...

  • Page 18: Further Characteristics

    • Firmware update (programming of the logic device) through HSP soft- ware service packs; removal of FETK or ECU is not necessary • Mounting the FETK-T4.0B via heat spreader directly to the ECU housing is recommended • Heat distribution •...

  • Page 19: Hardware Description

    FETK-T4.0B interface. This process enables adjustments of parameters, characteristic lines and maps through the calibration and development system. Using a trace interface, the FETK-T4.0B can aquire measurement data and send the measured data to the PC. FETK-T4.0B - User Guide...

  • Page 20: Ecu Interface

    Power supply ECU Interface The FETK-T4.0B is connected via connectors CON1, CON2, and CON4 to the ECU with three adapter cables (refer to Fig. 4-2 on page 20). The pin definition depends on the application and the microcontroller type. In general the ECU interface consists of •...

  • Page 21: Fetk Ethernet Interface

    NOTE The FETK Ethernet interface utilizes a proprietary Ethernet protocol and is compatible only with the Gigabit Ethernet interfaces of the ES89x ECU Inter- face Module. CON3 Fig. 4-3 Location of the Ethernet Interface Connector (CON3) FETK-T4.0B - User Guide...

  • Page 22: Power Supply

    The FETK is suitable for 12 V and 24 V systems. In 24 V systems the load dump capability is reduced. The FETK-T4.0B will also accept voltage drops down to 3 V, for a maximum duration of 15 ms (for additional details of low voltage operation, see ISO stan- dard 16750).

  • Page 23: Status Leds

    ETAS Hardware Description Status LEDs There are three LEDs displaying the operating status of the FETK-T4.0B (Fig. 4-5 on page 23). LED green LED red LED yellow Fig. 4-5 Status LEDs State Definition FETK-T4.0B is supplied with power and active (i.e. the ECU...

  • Page 24: Data Access

    4.7.1 Calibration Data Access The FETK-T4.0B is a serial FETK using SWD and a trace interface as the pri- mary microcontroller interface. Typical of all serial ETKs, XETKs and FETKs, the RAM used for data emulation and data measurement is not accessible by the FETK until the microcontroller is powered up and the startup handshake is per- formed.

  • Page 25: Measurement Data Access

    Hardware Description 4.7.2 Measurement Data Access The FETK-T4.0B is a serial FETK, so all data to be measured is located in the ECU memory. It can be read out by the FETK-T4.0B in two ways: • Trace measurement using the Aurora trace interface •...

  • Page 26: Swd Interface

    SWD Interface Fig. 4-6 Equivalent Circuitry of the ECU SWD Interface (ECU) The FETK-T4.0B operates the Single Wire Debug (SWD) interface. The FETK- T4.0B hardware incorporates 22 Ohm series termination resistors for the out- put ports SWCLK, SWDIO, TDO and /TRST.

  • Page 27: Trigger Modes

    • up to 255 value based trace trigger are supported. NOTE It is not possible to use the FETK-T4.0B configured with trace triggers and a debugger with program / data trace simultaneously. 4.10.3 Pinless Triggering 4.10.3.1...

  • Page 28: Timer Triggering

    4.12 Reset The requirement for the FETK-T4.0B reset mechanism is to ensure that power- up and power-down behavior of ECU is clean and smooth. The FETK-T4.0B generates a /PORST on user request, only. In case of a reconfiguration of the FETK-T4.0B INCA asks the user if a reset shall be performed...
  • Page 29 T4.0B to detect when the ECU is in reset. NOTE The reset signal /PORST can be hold or pulled low while the FETK-T4.0B is booting depending on the use the adapter ETAM8A or the adapter ETAM8B (see chapter “ETAM8 Adapter” on page 68). The FETK-T4.0B has to be config- ured in the XCT tool according to the needed reset signal characteristic during FETK-T4.0B standby.

  • Page 30: Pull Calwakeup Until Startup Handshake

    When waking up the ECU via the CalWakeUp pin, it can be configured if the pin is driven high until the microcontroller core voltage (VDDP) is high or if the pin should be driven high until the start-up handshake between ECU and FETK is complete. FETK-T4.0B - User Guide...

  • Page 31: Installation

    This chapter contains information about the following topics: • Mounting the FETK-T4.0B into the ECU Housing ....31 • Connection to the ECU ......... 35 •...

  • Page 32: Mounting Material

    ETAS Installation 5.1.2 Mounting Material To mount the FETK-T4.0B to the ECU housing several materials are required: • FETK-T4.0B • ECU metal housing with machined holes aligning with FETK-T4.0B hole pattern (see chapter “Mechanical Dimensions” on page 55 • Heat conductive paste with a thermal conductivity > 0.75 W/ (m · K) •...

  • Page 33: Fig. 5-2 Attaching The Fetk-T4.0B To The Ecu

    Attaching the FETK-T4.0B to the ECU Housing Fig. 5-2 Attaching the FETK-T4.0B to the ECU 1. Align the threaded drill holes of the FETK-T4.0B to the open- ings in the ECU housing. 2. Insert the screws into the holes in the ECU housing.

  • Page 34: Fig. 5-3 Thread Locking Fluid

    ETAS Installation CAUTION Risk of damage any components of the FETK-T4.0B! When mounting the FETK-T4.0B to the ECU, there is a risk of damage any components while tightening the nuts of the FETK-T4.0B. Locking the nuts Fig. 5-3 Thread Locking Fluid 1.

  • Page 35: Connection To The Ecu

    When you mount the FETK to the ECU, you must ensure that the screws and washers used will not penetrate the FETK printed circuit board. For connecting the FETK-T4.0B to the ECU three FETK adapter cables are rec- ommended: •...

  • Page 36: Fig. 5-5 Fetk-T4.0B Connection To The Ecu

    ETAS Installation Fig. 5-5 FETK-T4.0B Connection to the ECU FETK-T4.0B - User Guide...

  • Page 37: Wiring

    The FETK Ethernet interface utilizes a proprietary Ethernet protocol and is compatible only with the Gigabit Ethernet interfaces of the ES89x ECU Inter- face Module. Power Supply The FETK-T4.0B needs a permanent power supply (refer chapter “Power Sup- ply” on page 22). 5.4.0.1 Permanent Power Supply inside ECU available...

  • Page 38: Fig. 5-8 Fetk-T4.0B Power Supply Wiring With Cbam320.1 Cable

    E.g. Cable CBE260 Vehicle Power Supply Wiring Connector ECU GND FETK Vehicle Connector Battery Fig. 5-8 FETK-T4.0B Power Supply wiring with CBAM320.1 Cable Lemo Socket Serial ETK Interface Connector Cable CBAM350.1 E.g. Cable CBE260 Vehicle Power Supply Connector Wiring ECU GND FETK...

  • Page 39: Fig. 5-10 Fetk-T4.0B Power Supply Wiring With Cbam305.1 Cable

    FETK-T4.0B Power Supply wiring with CBAM305.1 Cable 5.4.0.3 Isolated Power Supply inside ECU The FETK-T4.0B does not require a galvanically isolated power supply. For spe- cial applications ETAS can offer a isolated power supply unit Power Supply Connector Isolated Power Supply...

  • Page 40: Etk / Xetk / Fetk Configuration

    ETK / XETK / FETK is checked for the appropriate configuration. If necessary, the ETK / XETK / FETK will be configured appropriately to the cor- responding project. FETK-T4.0B - User Guide...

  • Page 41: Configuration Parameter

    The XCT help window opens. 3. Choose Reference to User Interface > (X)ETK Hardware Configuration Parameters. 4. Choose the topic FETK-T4.0B. The topic FETK-T4.0B contains information about the FETK- T4.0B hardware configuration parameters and their possible values. FETK-T4.0B - User Guide...

  • Page 42: Technical Data

    Mechanical Dimensions........55 System Requirements 7.1.1 ETAS Compatible Hardware ETAS Hardware: ES89x ECU Interface Modules 7.1.2 PC with one Ethernet Interface A PC with one open Ethernet interface (1 Gbit/s) with RJ-45 connection is required to connect the ES89x module.

  • Page 43: Software Requirements

    7.2.1 Data Emulation Memory and Microcontroller Support The FETK-T4.0B uses a portion of or up to the entire size of an overlay RAM, to emulate data in internal flash. All the handle sizes must be equally sized. Up to 96 handles are supported.

  • Page 44: Trace Memory

    Inside the ECU housing the max. temperature is specified with 110 °C, still air. Outside of the ECU the max. ambient temperature is assumed to be 105 °C at 1 m/s airflow. The power dissipation of the FETK-T4.0B will be max. 5.2 Watt. NOTE It is recommended to mount the FETK-T4.0B via the heat spreader directly to...

  • Page 45: Fetk Ethernet Interface

    6,00 5,11 5,00 4,09 4,00 3,07 3,00 2,04 2,00 1,02 1,00 0,00 Ambiente‐Temperature  in °C Fig. 7-1 Max. Thermal Resistance from FETK-T4.0B Heatspreader-Surface to Ambiente [°C] FETK-T4.0B Heatspreader-Ambiente [K/W] Ambiente 9.20 8.18 7.16 6.13 5.11 4.09 3.07 2.04 1.02 = (125 - 10 - | T |) / 4.89 K/W...

  • Page 46: Power Supply

    The values above are not including the power dissipation of the microcontrol- ler ED-RAM part. NOTE The FETK-T4.0B will accept permanent power supply voltage dips (for addi- tional details of 3 V low voltage operation, see ISO standard 16750). FETK-T4.0B - User Guide...

  • Page 47: Microcontroller Interface

    Batt NOTE The reset signal /PORST can be hold or pulled low while the FETK-T4.0B is booting depending on the use the adapter ETAM8A or the adapter ETAM8B (see chapter “ETAM8 Adapter” on page 68). The FETK-T4.0B has to be config- ured in the XCT tool according to the needed reset signal characteristic during FETK-T4.0B standby.

  • Page 48: Swd Timing Characteristics

    ETAS Technical Data SWD Timing Characteristics The FETK-T4.0B supports the 2-pin SWD mode: one data pin (direction via pro- tocol), one clock pin. NOTE SWD timing parameters in this chapter refer to the SWD interface (CON2) of the FETK-T4.0B. The SWD wiring to the ECU (ETAM8) must be taken account additionally.

  • Page 49: Electrical Characteristics

    7.10 Electrical Characteristics 7.10.1 ECU Interface Connector (DAP) Signal (max) (min) (max) (max) (min) (max) Leakage current Addit. load Type (max)/ (min) by ETK (typ) [A] [pF] SWCLK +745 / +475 SWDIO +50 / -82 Reserved (TDO) +5000 / +3340 Reserved (TDI) +20 / -20 /TRST...

  • Page 50: Ecu Interface Connector Aurora Trace

    7.10.2 ECU Interface Connector Aurora Trace Signal Pin Type V Leakage current Additional load by ETK (max) (min / max) (typ) (max) (min) (max) (min) (max) [A] [pF] TRACETRIG -144 / -58 RESERVED +30 / -30 (CRC_ERROR) Pin Type: I: Input, X: Tristate, O: Output, OD: Open Drain Adapter cable and Samtec connector not considered;...

  • Page 51: Pin Assignment

    Pin Assignment NOTE The tables describes the pin assignment at the ETK side. CON1 CON2 CON3 CON4 Fig. 7-2 Location of the FETK-T4.0B Interfaces 7.11.1 ECU Interface Connector CON1 (SWD Mode) CON1 Fig. 7-3 ECU Interface Connector CON1 Signal Direction...
  • Page 52 "Overwrite /PORST status at Power On, 0 V = /PORST inactive, 3.3 V = active" VDDP (Sense) Input Sense for Switched power supply of ECU (ignition) 3, 6, Power Signal Ground 9, 12, Output DNU, Mfr test signal Not Connected FETK-T4.0B - User Guide...

  • Page 53: Ecu Interface Connector Con2 (Aurora Trace)

    Aurora Data Lane 1 Data1-N Input Data2-P Input Aurora Data Lane 2 Data2-N Input Data3-P Input Aurora Data Lane 3 Data3-N Input TraceTrigger Input Do not use RESERVED Output RESERVED (Aurora CRC_ERROR) (CRC_ERROR) 1, 2, GND Signal 7, 8, FETK-T4.0B - User Guide...

  • Page 54: Ethernet Interface Connector Con3

    Ubatt2 Input Vehicle battery Ubatt1 Input Vehicle battery NOTE VDDSTBY may not be used as power supply of the microcontroller core. VDDSTBY is permanently available and must be used as power supply of the EDRAM, only. FETK-T4.0B - User Guide...

  • Page 55: Mechanical Dimensions

    45.25 1.781 Height 11.55 0.455 Height 14.90 0.587 : without adapter connectors : ETAM2 mounted at CON4 7.12.1 Top View Fig. 7-7 FETK-T4.0B Dimensions - Top View Item Dimension Tolerance Dimension Tolerance [Millimeters] [Millimeters] [Inches] [Inches] 56.50 +/- 0.2 2.224 +/- 0.008...

  • Page 56: Side View

    ETAS Technical Data 7.12.2 Side View Fig. 7-8 FETK-T4.0B Dimensions - Side View Item Dimension Tolerance Dimension Tolerance [Millimeters] [Millimeters] [Inches] [Inches] 4.20 +/- 0.10 0.165 +/- 0.004 1.60 +/- 0.16 0.063 +/- 0.006 5.75 +0.0 0.226 +0.000 -0.2 -0.008...

  • Page 57: Cables And Accessories

    See chapter 5.3 on page 37 for details on wiring the ECU interface adapters. NOTE We recommend to use ETAS cables or any other cables certified by the stan- dards for the application. Adhere to the maximum permissible cable lengths! NOTE Application-specific cables are available from ETAS.

  • Page 58: Cbam300 Cable

    Shield ECU housing 8.3.3 Temperature Range Condition Temperature Operating temperature -40 °C to +125 °C 8.3.4 Tightness Condition IP Code PG9 screwing IP67 8.3.5 Ordering Product Length Order Number CBAM300.3-0m6 0.6 m F 00K 112 469 FETK-T4.0B - User Guide...

  • Page 59: Cbam320 Cable

    CON2 White FETK 8.4.3 Temperature Range Condition Temperature Operating temperature -40 °C to +125 °C 8.4.4 Tightness Condition IP Code PG8 screwing IP67 8.4.5 Ordering Product Length Order Number CBAM320.1-0m6 0.6 m F 00K 109 299 FETK-T4.0B - User Guide...

  • Page 60: Cbam340 Cable

    FETK ECU Adapter Cable, shield on ECU-Housing NOTE The hardware for mounting ECU adapter cables is not included in the cable delivery, they need to be ordered separately. For detailed information on mounting accessories contact ETAS technical support. 8.5.2 Connectors Fig. 8-6...

  • Page 61: Cbam350 Cable

    (not included in the delivery). NOTE The Lemo Spanner DCH.91.161.PA is not included in the cable delivery, It need to be ordered separately. For detailed information on mounting acces- sories contact ETAS technical support. FETK-T4.0B - User Guide...

  • Page 62: Temperature Range

    ETAS Cables and Accessories 8.6.4 Temperature Range Condition Temperature Operating temperature -40 °C to +125 °C 8.6.5 Ordering Product Length Order Number CBAM350.1-0m17 0.17 m F 00K 111 439 FETK-T4.0B - User Guide...

  • Page 63: Cbam305 Cable

    For mounting the cable, cut a PG9 thread into the ECU housing. For thin walled housings use a nut SM-PE 9. It is available from Lapp (order number: 52103210). 8.7.2 Dimensions Fig. 8-9 CBAM305.1-0m6 Cable - Dimensions FETK-T4.0B - User Guide...

  • Page 64: Connectors

    CON4 FETK UBATT Connector Color Target CON1 Blue lila Gbit Ethernet cable, e.g. CBE260 CON2 White FETK CON3 Black Permanent power supply, K70.1 cable CON4 2 pin ERNI power ECU connector Fig. 8-12 CBAM305.1-2m2 - Connectors FETK-T4.0B - User Guide...

  • Page 65: Temperature Range

    Temperature Operating temperature -40 °C to +125 °C 8.7.5 Tightness Condition IP Code PG9 screwing IP67 8.7.6 Ordering Product Length Order Number CBAM305.1-0m6 0.6 m F 00K 109 297 CBAM305.1-2m2 2.2 m F 00K 112 338 FETK-T4.0B - User Guide...

  • Page 66: Cbe260 Cable

    Gigabit Ethernet and Power Connection cable for FETK. Lemo connectors on both sides compliant to IP65. 3 m length. The CBAE260 cable is a Gigabit Ethernet cable to connect an ETAS ES device with an FETK or another ES device. The cable supports power propagation.

  • Page 67: Etam4 Adapter

    The ETAM4 covers only the trace specific signals. All other signals a covered by ETAM1 and ETAM2 adapter. 8.9.2 Pin Numbering Fig. 8-18 ECU Adapter ETAM4 (Pin Numbering) 8.9.3 Ordering Product Length Order Number ETAM4 0.17 m F 00K 109 979 FETK-T4.0B - User Guide...

  • Page 68: Etam8 Adapter

    ETAM8A hold the ECU in Reset, while the ETK is booting. • ETAM8B do not pull the Reset low while booting. With a ETAM8B adapter the FETK-T4.0B has the same reset behavior like FETK-T1.0. NOTE See chapter "Installation" for details on mating connector to the ETAM8.

  • Page 69: Temperature Range

    /PORESET /PORESET /PORESET /PORESET 8.10.4 Temperature Range Condition Temperature Operating temperature -40 °C to +110 °C 8.10.5 Ordering Product Length Order Number ETAM8A 0.11 m F 00K 110 754 ETAM8B 0.11 m F 00K 110 881 FETK-T4.0B - User Guide...

  • Page 70: Etv5 Cable

    Not connected Brown Power GND Not connected SGUBATT1 Car Battery Not connected 8.11.3 Temperature Range Condition Temperature Operating temperature -40 °C to +110 °C 8.11.4 Ordering Product Length Order Number ETV5 0.25 m F 00K 111 701 FETK-T4.0B - User Guide...

  • Page 71: Etam2 Adapter

    Permanent power to supply ECU ED-RAM (Supply) Brown Power ground Green CAL_Wakeup Switch to Ubatt. ECU wake-up signal (for measurement preparation) SGUBATT2 Car battery SGUBATT1 Car battery 8.12.3 Ordering Product Length Order Number ETAM2 0.25 m F 00K 109 306 FETK-T4.0B - User Guide...

  • Page 72: Etam5 Adapter

    Wire: 5 mm stripped Molex and tinned Side A Medi cable Side C Side B Position Color Position Position Blue Yellow Brown Green 8.13.2 Ordering Product Length Order Number ETAM5 0.136 m F 00K 110 101 FETK-T4.0B - User Guide...

  • Page 73: Etam9 Adapter

    No Connect 8.14.3 Temperature Range Condition Temperature Range Operating temperature -40 °C to +110 °C 8.14.4 Order Information Product Length Order Number ETAM9 F/XETK-S ECU Adapter, MOLEX - 0.136 m F 00K-111-043 MOLEX (6fc - 5fc), 0m136 FETK-T4.0B - User Guide...

  • Page 74: Etam10 Adapter

    ETAM10 adapts the ETK power signals (Molex 6 pin connector) to an ECU with a 6 pin Molex PicoSpox connector. The ECU connector is available as Vertical SMT Header [87437-0643] or Right Angle SMT Header [87438-0643]. 8.15.2 Dimensions Fig. 8-28 ETAM10 Adapter Dimensions FETK-T4.0B - User Guide...

  • Page 75: Ecu Signals

    Car battery 8.15.4 Temperature Range Condition Temperature Range Operating temperature -40 °C to +110 °C 8.15.5 Order Information Product Length Order Number ETAM10 F/XETK-S ECU Adapter, MOLEX - 0.07 m F 00K-111-814 MOLEX (6fc - 6fc), 0m07 FETK-T4.0B - User Guide...

  • Page 76: Ordering Information

    • China-RoHS-leaflet_Compact_cn Cable NOTE We recommend to use ETAS cables or any other cables certified by the stan- dards for the application. Adhere to the maximum permissible cable lengths! Please contact your local ETAS representative for further cable information. 9.2.1...

  • Page 77: Ecu Adapter And Power Supply Cable

    (2fc-1c), 0m60 FETK ECU Adapter and Power Supply CBAM305.1-2m2 F 00K 112 338 Cable, pre-assembled into PG9 screwing, shield on ECU-Housing, Lemo 1B PHM - JST SHR (10fc-9fc) / Lemo 0B PHG - open wire (2fc-1c), 2m2 FETK-T4.0B - User Guide...

  • Page 78: Gbit Ethernet And Power Supply Cable

    MOLEX (6fc - 5fc), 0m136 ETAM10 F/XETK-S ECU Adapter, MOLEX - ETAM10 F00K 111 814 MOLEX (6fc - 6fc), 0m07 Power Supply For special applications ETAS can offer a isolated power supply unit. For detailed information contact ETAS technical support. FETK-T4.0B - User Guide...

  • Page 79: Contact Information

    Germany Internet: www.etas.com ETAS Subsidiaries and Technical Support For details of your local sales office as well as your local technical support team and product hotlines, take a look at the ETAS website: ETAS subsidiaries Internet: www.etas.com/en/contact.php ETAS technical support Internet: www.etas.com/en/hotlines.php...

  • Page 80: Figures

    Attaching the FETK-T4.0B to the ECU ........33...
  • Page 81 ETAM10 Adapter Dimensions ......... .74 FETK-T4.0B - User Guide...

  • Page 82: Index

    Isolated Power Supply ....39 LED ....... .23 FETK-T4.0B - User Guide...

Table of Contents