Table of Contents
Advertisement
Quick Links
H_D710ABS, H_E710ABS, H_C1010ABS, H_C1410ABS,
H_C1010WBS, H_C1410WBS,
H_E1010ABS, H_E1410ABS,
H_E1010WBS, H_E1410WBS
(See model number configurator on page 2 for details.)
Order parts online
www.follettice.com
Horizon Elite
Ice Machine Models with RIDE
™
Installation Instructions for Ice Storage Bins
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Technology
™
self-contained
01113240R05
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Follett Horizon Elite Chewblet H D710ABS Series
Summary of Contents for Follett Horizon Elite Chewblet H D710ABS Series
- Page 1 Horizon Elite Ice Machine Models with RIDE Technology ™ ™ Installation Instructions for Ice Storage Bins H_D710ABS, H_E710ABS, H_C1010ABS, H_C1410ABS, H_C1010WBS, H_C1410WBS, H_E1010ABS, H_E1410ABS, H_E1010WBS, H_E1410WBS (See model number configurator on page 2 for details.) Order parts online www.follettice.com self-contained 801 Church Lane •...
- Page 2 Chewblet Ice Machine Model Number Configurations ® 1810 Application Configuration Icemaker Voltage Series Condenser MC Maestro™ C 208-230/60/1 (icemaking head) 425 up to A Air-cooled, self-contained V Vision™ S RIDE™ Self-contained only. 425 lbs Chewblet ® W Water-cooled, self-contained H Harmony™ (RIDE remote D 115/60/1 (icemaking head) (193 kg)
- Page 3 Read and complete the following 8 installation steps Unpack Site preparation Bin preparation Docking assembly External connection Ice transport tube Internal connection Front cover BIN • RIDE Technology self-contained...
- Page 4 Unpack Carefully unpack and inspect the contents of your Follett ice machine. Unpack ice machine ➋ ➌ ➊ ➎ ➍ 7/16" DO NOT TILT ICE MACHINE TO ACCESS BOLTS! COMPRESSOR DAMAGE 7/16" WILL RESULT ➐ ➏ BIN • RIDE Technology...
-
Page 5: Site Preparation
• 10-70 psi (69-483 kpa) • 45 to 90 F (7 to 32 C) • Follett recommends the use of an in-line water filtration system (item# 00130286) • This equipment is to be installed with adequate backflow protection to comply with applicable federal, state, and local codes ➌... - Page 6 Bin preparation Prepare the bin Bin top preparation Bin top preparation — – ˜ – • Remove protective tape from gaskets • Apply gaskets ➊ • Install shuttle actuator ➋ through dispenser top and secure with locking nut ➌ BIN • RIDE Technology self-contained...
- Page 7 Docking assembly Install the docking assembly. BEFORE PROCEEDING Prior to installing the docking assembly, ensure that the drain fitting is oriented (right or left) correctly for your installation. An optional straight drain fitting is also supplied. You may need to remove the back panel of the docking assembly in order to re-orient or change the drain fitting.
-
Page 8: Ice Transport Tube
Ice transport tube Install the ice transport tube. Ice transport tube installation ➍ ➏ ➐ ➋ Hot Water 160 F (71 C) ➎ ➑ ➒ ➊ ➓ 1/4˝ (6,4mm) ➌ 1' (0,3m) Ice transport tube tips ➊ • Insulate entire length of ice transport tube •... -
Page 9: External Connections
External connections Connect utilities to docking assembly. Air-cooled ice machines only Water-cooled ice machines only ➊ ➊ ➋ ➏ ➋ ➐ ➌ ➌ Minimum 8" Minimum 8" ➏ ➑ radius radius 2 ft. x 1" OD 2 ft. x 1" OD silicone tubing silicone tubing 3/4"... - Page 10 Chassis drain plumbing - required • Plug must be removed from John Guest fitting. • Route 3/8" drain tubing through knockout in back of docking station and insert fully into John Guest fitting connection at the rear of the machine chassis. Route other end of 3/8"...
-
Page 11: Internal Connections
Internal connections Connect docking assembly to ice machine. CAUTION • Plug must be accessible after final installation. • H_E1410A/W 230/50/1 requires a 20A circuit (4.00 mm wire) Air-cooled ice machines – follow steps 7.1 through 7.5. Water solenoid, shut-off valve, Ice transport tube and potable water line options If water solenoid is already mounted to... - Page 12 Water-cooled ice machines – follow steps 7.6 through 7.12. Cooling lines Set TDS switch HIGH CLEAN • Install ice machine cooling water lines to • Set the TDS switch on the electrical box: docking assembly HIGH: for extended service life LOW: for low-scale water Ice transport tube Water solenoid, shut-off valve,...
- Page 13 7.10 Power cord Cooling lines and power ➋ ➊ • Remove twist tie • Carefully pass cord through opening and • Connect cooling water lines to ice plug into wall outlet machine ➊ • For H_E units, install a suitable plug •...
-
Page 14: Front Cover
Front cover Install front cover to ice machine. Install front cover Front cover installation – air-cooled undercounter only ➊ ➋ ➋ ➌ ➊ ➌ • Slide ice machine cover over machine ensuring that tabs on back of cover slip under louvers on back of docking assembly ➊... - Page 15 Long tube run recommendations max. 2 ft (0,6m) ➊ ➋ 1/4" (6,4mm) 1' (0,3m) ➊ • Pitch ice transport tube to allow melt water to drain towards ice machine ➋ • Secure insulated ice transport tube at least every 2 ft (0,6 m) to prevent dips or traps BIN •...
- Page 16 Maestro, Micro Chewblet, Vision, Harmony, Ice Manager, Horizon, Horizon Elite are trademarks of Follett Products LLC. Chewblet, RIDE, Follett are registered trademarks of Follett Products LLC. 801 Church Lane • Easton, PA 18040, USA 01113240R05 Toll free (877) 612-5086 • +1 (610) 252-7301 ©...
Need help?
Do you have a question about the Horizon Elite Chewblet H D710ABS Series and is the answer not in the manual?
Questions and answers