Operational Checkout - NuTone IM-5006 Series Installation Instructions Manual

OPERATIONAL CHECKOUT

NOTE: Please refer to page 10 for a convenient Operational Checklist.
1. When the system is first powered up, the display will
appear as 12:00 AM. To ensure that no incorrect data has
been stored in the system's memory during shipment
and/or installation, a total system reset should be done at
the master station by simply pressing
station's keypad.
2. Select FM radio and tune to a radio station that has a
strong signal by using the following procedure:
A) Press the ON/OFF key - the LED next to the key will
be lit.
B) Press the FM key - the LED next to the key will be lit
and FM 87.9 will appear in the display.
C) Tune to a station by pressing the
master station.
Beginning with the master station, use the following
procedure at each station to check for proper operation:
1. Adjust the radio volume keys to be certain the volume is
operating properly.
NOTE: The radio audio cannot be turned completely off
at the master station by using the radio volume key; the
mute key must be used.
2. Press the PRIVATE key; the PRIVATE LED will be lit and
the station will be in the private mode.
In the private mode, the station cannot accept an
intercom call.
3. Press the PRIVATE key again and the PRIVATE LED will
go out and the station will again be able to accept intercom
calls.
4. Press the MONITOR key; the MONITOR LED will be lit
and audio from this station will be heard at all of the other
stations.
5. Press the MONITOR key again and the MONITOR LED
will go out and the station will no longer be in the monitor
mode.
6. Press the ALL CALL key; the ALL CALL LED will be lit at
this station. A call tone will be heard at every station in the
system. Radio audio will be muted and audio from every
station will be heard at the station that initiated the all call.
The intercom volume key may be used to adjust the
audio at the initiating station. NOTE: The intercom
volume cannot be completely muted.
7. Press the TALK key. Audio from the initiating station will
be heard at all the stations in the system.
When the TALK key is released, audio from the other
stations will be heard at the initiating station.
*
8# at the master
< >
or key at the
9
8. Press the END CALL key and the ALL CALL LED will
go out at the initiating station. The radio audio will now be
heard at all stations.
9. Press the DOOR key; the DOOR LED will be lit at the
initiating station and the BUSY LED's will be lit at each of
the other stations. A call tone will be heard at the initiating
station only; not at the door speaker. Audio from the door
speaker will be heard at the initiating station.
10. Press the TALK key. Audio from the initiating station will
be heard at the door speaker.
When the TALK key is released, audio from the door
speaker will be heard at the initiating station.
11. Press the END CALL key. The DOOR LED will go out at
the initiating station and the BUSY LEDs will also go out
at all of the other stations. The radio audio will now be
heard at the initiating station.
12. Use the following procedure to initiate a "select" intercom
call:
a) Using the station's keypad, call another station in the
system.
NOTE: When a station has been assigned a station
code of one digit (1-9), the code must be entered
with a zero (0) preceding the assigned number.
Example: to call station #2, press 02 on the key
pad. When the second digit is entered, a call tone
will be heard at the station that initiated the call as
well as at the station that has been called. Radio
audio will be muted at both of these stations.
b) The BUSY LED will be lit at all other stations; audio
from the station that has been called will be heard at
the station that initiated the intercom call.
c) Press the TALK key. Audio from the station that
initiated the intercom call will be heard at the station
that has been called.
d) Release the TALK key. Audio from the station that
has been called will be heard at the station that
initiated the intercom call.
e) Press the END CALL key. The radio audio will be
heard at both stations. The BUSY LED's will go out at
all other stations in the system.
f) Continue to check the system by making select
intercom calls to each speaker location.