Table of Contents
Advertisement
SYSTEM OPERATING CONTROLS
Operational Checkout
If the system does not operate according to the following
instructions, refer to the installer's Troubleshooting Guide.
1.
Set STATION STATUS SWITCHES to RADIO/IP position.
2.
Set the MASTER VOLUME control to maximum.
3.
Set each individual remote station VOLUME control to
maximum.
4.
Set the SYSTEM VOLUME control to 1/3 position.
5.
Set the INTERCOM VOLUME control to 3/4 position.
6.
Set the BASS and TREBLE controls to 1/2 position.
7.
Tune in a strong local FM radio station as follows:
A. Press the PROGRAM ON/OFF key.
B. Press the PROGRAM SELECT key until the FM radio
is selected and displayed in the LCD display.
C. Use the
keys to locate a strong local FM
radio station.
Beginning with the master station, check each station in the
system for proper operation using the following procedure:
1.
Adjust all station's VOLUME controls (MASTER VOLUME
on the master station) between maximum and minimum
making sure the audio is completely muted in the minimum
position.
2.
Press the INSIDE/PATIO key. Radio audio will mute and
audio from the initiating station will be heard at all stations
in the system, except the door speaker(s).
3.
Release the INSIDE/PATIO key and have an assistant
press the INSIDE/PATIO key on another speaker to hear
the reply.
4.
Press the END CALL key. Intercom communication will
end, and radio audio will return to all stations in the
systems.
5.
Press the DOOR TALK key. Radio audio will mute, and
audio from the initiating station will be heard at the door
speaker(s) and all the stations in the system.
6.
Release the DOOR TALK key. Audio from the door
speaker(s) will be heard at all stations in the system.
7.
Press END CALL key. Door communication will end, and
radio audio will return to all stations in the system.
8.
Press and hold the END CALL key for 2 seconds at any
remote station(not at the master station). The radio will
turn off.
9.
Press and hold the END CALL key for 2 seconds at any
remote station(not at the master station). The radio will turn
on. For additional information on remote radio control, refer
to the homeowner's manual.
10. Repeat this procedure at all remote stations.
Setting Program Audio
Controls
The volume levels required at each station may vary with the
location of the speaker and the size of the room where the
speaker is located. Spend some time experimenting with
volume levels, and adjust each speaker so that you can clearly
hear the radio and intercom. Use the following procedures to set
your system's volume levels.
1. At each remote station, turn the VOLUME control completely
clockwise to maximum volume.
2. At the master station, set the REMOTE SPEAKER STATUS
switches to the RADIO/IP position.
3. Turn the MASTER VOLUME control to maximum volume.
4. Turn the SYSTEM VOLUME control on the master station to
approximately 1/3 level.
5. Select an AM or FM radio station with a strong, clear signal.
6. Adjust the master station's SYSTEM VOLUME control until
you have enough volume at the remote station that requires
the highest volume (i.e. a large living room, family room,
basement, etc.).
NOTE: The master station and all remote stations (except
the door speakers) are equipped with their own volume
controls. Although the master station's SYSTEM VOLUME
sets the System's Volume Level, you may adjust an
individual speaker's volume level as desired.
7. Adjust the MASTER VOLUME control and all remote
stations' volume controls to the volume level you desire.
8. In order to have proper intercom audio levels, it is
recommended that the MASTER VOLUME and REMOTE
STATIONS' VOLUME controls be set at 2/3 or above.
Setting Intercom Volume
1. Initiate intercom call from the master station by pressing the
INSIDE/PATIO key.
2. Speak with a normal voice about 2-3 feet from the master
station's speaker.
3. Adjust the INTERCOM VOLUME control until the initiating
station's audio is clearly heard at all stations in the system.
NOTE: The volume control at all stations should be set
between 2/3 and maximum volume for proper intercom
operation.
4. Repeat the above procedure at several remote station
locations until an acceptable intercom audio level is achieved
at all stations.
9
(Continued)
Hide quick links:
Advertisement
Table of Contents
