Advertisement
SELECTIVE CALL INTERCOM SYSTEM
This booklet contains information for wiring and installing
the master station. All system wiring and remote station
rough-in frames should be installed before mounting and
connecting the master station.
IM-5000 SERIES REPRESENTATIVE WIRING ILLUSTRATION
Use this diagram for reference only
NUTONE CHIME
TRANSFORMER
120vAC, 60Hz
HOUSE POWER
PUSH
PUSHBUTTON FOR
BUTTON
OPTIONAL CHIME
MODULES
(UP TO 3 DOOR RUNS)
OPTIONAL
NUTONE
ELECTRONIC
DOOR CHIME
SEE CHIME
INSTALLATION
INSTRUCTIONS
200' MAX
NUTONE IW-2
SHIELDED
AUDIO
CABLES
OPTIONAL
MUSICAL
SOURCE
®
MODEL: IM-5000 MASTER STATION
CAUTION: DO NOT SUPPLY POWER
UNTIL LOW VOLTAGE POWER
CONNECTIONS ARE MADE IN
MASTER, 120vAC, 60H
OBSERVE LOCAL CODE. UL LISTED
CLASS 2 NUTONE MODEL 401T
TRANSFORMER MUST BE USED
14/2 WITH
GROUND
TRANSFORMER
SUPPLIED WITH
NUTONE S-143
ROUGH-IN
(18/2) MAX 50'
USE 14/2 FOR RUN
SECONDARY
BETWEEN 50-125'
24v, 40vA
EARTH
GROUND
14
300' MAX
GA
S-143
INTERCOM MASTER
DOOR SPEAKER
RECESS MODEL
MOUNTS IN
HOUSING OR
SURFACE MOUNTS
18/2
300' MAX
TO ADDITIONAL
REMOTE SPEAKER
STATION
INSTALLATION INSTRUCTIONS
Detailed information on wiring and mounting system
components (i.e. speakers, remote controls, etc.) are
packaged with each separate component.
, CLASS 1
Z
MASTER
FRAME
IW-6
MAXIMUM OF 750' RUN.
MAXIMUM OF 4000'
TOTAL WIRE.
IW-6
PATIO SPEAKER
W/CONTROLS.
INSTALLS IN
FRAME.
DOOR SPEAKER MODELS WITH
CHIME PUSHBUTTON ALSO
REQUIRE 18/2 (S-143) TO CHIME
LOCATION OR TO MASTER IF
OPTIONAL CHIME MODULE IS USED
8' 6 COND. CABLE
AND CONNECTOR
IW-6
INSIDE 5" SP.
WALL
W/CONTROL
RECEPTACLE
INSIDE 8" SP.
INSIDE REMOTE
CONTROL.
IW-6
IW-2
CONTROLS.
INSTALLS IN
25'
INSTALLS IN
FRAME.
MAX
OUTSIDE 8"
OUTSIDE
IW-6
IW-2
REMOTE
CONTROLS.
CONTROL.
25'
INSTALLS IN
INSTALLS IN
MAX
FRAME.
OUTSIDE 8"
OUTSIDE
IW-2
REMOTE
CONTROLS.
CONTROL.
25'
INSTALLS IN
INSTALLS IN
MAX
FRAME.
INSIDE 5" SP.
W/CONTROL.
IW-6
INSIDE 5" SP.
W/CONTROL.
INSTALLS IN
IW-6
MAX 3 CABLES
TO ONE SPEAKER
INSIDE 8" SP.
W/CONTROL.
INSTALLS IN
IW-6
ANGLED
DESKTOP
FRAME
W/O
FRAME.
SP. W/O
FRAME.
SP. W/O
FRAME.
ANGLED
SURFACE
MOUNT
FRAME
FRAME.
FRAME
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for NuTone IM-5000 series
Summary of Contents for NuTone IM-5000 series
- Page 1 (i.e. speakers, remote controls, etc.) are rough-in frames should be installed before mounting and packaged with each separate component. connecting the master station. IM-5000 SERIES REPRESENTATIVE WIRING ILLUSTRATION Use this diagram for reference only 8' 6 COND. CABLE AND CONNECTOR...
-
Page 2: System Specifications
• Chime module or electronic chime to pushbutton instructions, warranty registration and • Electronic chime to chime transformer homeowner's manual to homeowner. Use 14 ga. ground wire (not supplied by NuTone) for connecting: • Master to ground Use shielded audio cable for connecting: •... -
Page 3: Precautions And Guidelines
The IM-5000 Intercom System is designed to be used with NuTone specified wire; no other wire should be used. The use of wire other than NuTone wire will void all NuTone warranties and may result in faulty installation and improper operation. -
Page 4: Installation Instructions
Door Speaker Cable (IW-2) MASTER LOCATION Run all door speaker cables from the door speaker locations to the master station location. NuTone recommends home The following instructions apply to all cable placements to the run installation of door speakers; however, they can be master unit. - Page 5 INSTALLATION INSTRUCTIONS (Continued) Mounting the Master Connecting the IW-6 Remote Station Wiring at the Master Remove the master MASTER COVER cover from the base by Position the IW-6 remote station cables in the U-shaped slots. carefully inserting a screwdriver into either Strip back the outer insulation from each IW-6 cable.
- Page 6 Connecting an Optional MOUNTING STRIPE BRACKET Electronic Chime Strip back 5/8" of NuTone IW-2 wire from the optional electronic chime. Connect wires to the screw terminals INTERCOM marked "Electronic Chime" on the master. VOLUME Electronic chime package contains additional installation instructions.
-
Page 7: Powering Up The System
Make sure AC power to the 401T transformer and the the ON position. Power toggle switch at the master is OFF. Strip back 5/8" of the NuTone S-143 cable. Connect the cable from the 401T 24 volt transformer to the screw terminals on 1 & 2 the master base marked "24 VAC input". -
Page 8: Operational Checkout
The chime module audio may be selected to be controlled from the RADIO (MUSIC) VOLUME control or the Setting the Intercom Audio Level INTERCOM VOLUME control. The NuTone IM-5000 Selective Call Intercom chime module audio is factory preset In most installations, the "Intercom Volume" trimpot in the to be distributed through the RADIO (MUSIC) VOLUME master will not require adjustment. - Page 9 OPERATIONAL CHECKOUT (Continued) Placing the Master Cover Over the Completing the Installation Master Base Check (√) all items below for final system check. ❏ Master unit is properly aligned and securely installed. Position the top of the cover onto the top of the base. ❏...
- Page 10 INSTALLER'S TROUBLESHOOTING GUIDE TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY Hum in remote stations. The intercom wiring has been run Be certain the intercom wiring is as far away as practical too close to the household AC from the household AC power wiring. Do not run the power wiring.
- Page 11 INSTALLER'S TROUBLESHOOTING GUIDE TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY The system squeals when the The station in the adjacent room(s) If the remote stations have been mounted back to back, intercom is being used. is mounted on a common wall (back one of them will have to be relocated.
- Page 12 Product specifications subject to change without notice. 4820 Red Bank Road, Cincinnati, Ohio 45227 Printed in China, Rev. 4/02, Part No. 86024...
Need help?
Do you have a question about the IM-5000 series and is the answer not in the manual?
Questions and answers