Table of Contents
Advertisement
Service setup
dbl_sec_q1_out_error
dbl_sec_q2_out_error
dbl_sec_q3_out_error
dbl_sec_q3_out_warning
dbl_sec_release_pressure
dbl_sec_upw_desinf_sv6_close
dbl_sec_upw_desinf_sv6_open
dbl_sec_venting_upw
dbl_sec_venting_upw_sv6_close
dbl_sec_venting_upw_sv6_open
dbl_t3_limit_warning
dbl_t3_limit_warning_exit
dbl_tank_level_desinf
dbl_tank_level_min_dry
dbl_tank_level_min_init
dbl_tank_level_min_tap
dbl_tank_level_tool
str_backup_calib_file
str_backup_config_file
str_backup_file_high_density
str_backup_file_low_density
str_backup_file_mid_density
str_backup_file_op_hour
str_backup_log_file
str_first_start_device
str_path_file_high_density
str_path_file_low_density
str_path_file_mid_density
str_path_file_op_hour
str_path_log_file
str_path_temp_file
str_standard_device
str_tool_first_start
u16_mins_init_flush_ro
u16_mins_init_flush_ro_edi
u32_count_mins_desinfection
u8_ai_bit_q1
u8_ai_bit_q2
u8_ai_bit_q3
u8_ai_bit_q4
u8_ai_bit_t2
u8_ai_bit_t3
u8_ai_bit_t4
u8_ai_bit_tank
u8_ai_port_q1
u8_ai_port_q2
u8_ai_port_q3
u8_ai_port_q4
u8_ai_port_t2
u8_ai_port_t3
u8_ai_port_t4
u8_ai_port_tank
u8_chart_sensor
u8_chart_sensor_2
1800
1800
1800
180
8
10
10
30
5
5
40
38
70
10
50
15
50
\Had Disk\calib.mcf
\Hard Disk\config.mcf
\Hard Disk\data_high.dat
\Hard Disk\data_low.dat
\Hard Disk\data_mid.dat
\Hard Disk\op_hour.dat
\Hard Disk\log_file.dat
init_device_1
\NandFlash\data_high.dat
\NandFlash\data_low.dat
\NandFlash\data_mid.dat
\NandFlash\op_hour.dat
\NandFlash\logfile.dat
\NandFlash\temp.dat
aquinity
tool_first_start
15
60
129600
0
0
0
0
0
0
0
0
1
3
5
7
4
6
8
13
0
0
30 mins Q1 problem -> STOP
Q2 is out of range (30 min) STOP
Q3 < 0.045µS (30 mins) -> STOP
Q3 > limit (3 mins) -> WARN
Time to release pressure (8 sec)
SV6 close for (10 s) by disinfection
SV6 open for (10 s) by disinfection
30 secs venting UPW
Venting PW -> SV6 close (5 sec)
Venting PW -> SV6 open (5 sec)
T3 max. -> show Warning
T3 -> exit Warning
minimal Tank (%) to start disinfection
10% Tank level dry-protection
Min (50%) Tank level for first start
Min (15%) Tank level for water tap
minimal (%) Tank to start UPW/UF tool
Path of calibration file backup
Path of config file backup
Path of data high file backup
Path of data low file backup
Path of data mid file backup
Path of operating hour file backup
Path of logfile backup
Default state of initial process
Path of data high file
Path of data low file
Path of data mid file
Path of operating hour file
Path of logfile
Path of temp file
Default state of normal process
Default state of first tool process
15 mins init FlushRO (AQ²P, AQ²P10)
Init. FlushRO EDI for 60 mins (AQ²E)
Reminder of desinfection (3 Months)
0(12-bit), 1(14-bit), 2(16-bit), 3(18-bit)
0(12-bit), 1(14-bit), 2(16-bit), 3(18-bit)
0(12-bit), 1(14-bit), 2(16-bit), 3(18-bit)
0(12-bit), 1(14-bit), 2(16-bit), 3(18-bit)
0(12-bit), 1(14-bit), 2(16-bit), 3(18-bit)
0(12-bit), 1(14-bit), 2(16-bit), 3(18-bit)
0(12-bit), 1(14-bit), 2(16-bit), 3(18-bit)
0(12-bit), 1(14-bit), 2(16-bit), 3(18-bit)
AI-port Q1
AI-port Q2
AI-port Q3
AI-port Q4
AI-port T2
AI-port T3
AI-port T4
AI-port tank
Display sensors for Service
Display sensors for Customer
Page 62
Advertisement
Table of Contents
