Infineon TLD5099EP User Manual
Voltage-mode boost to ground evaluation kit
Hide thumbs
Also See for TLD5099EP:
- User manual (15 pages) ,
- Quick start manual (15 pages) ,
- User manual (19 pages)
Table of Contents
Advertisement
Quick Links
Z8F67904849
Voltage-mode boost to ground evaluation kit
TLD5099EP
About this document
Product description
The TLD5099EP is an AEC qualified DC-DC boost controller, especially designed to drive LEDs.
•
Built in diagnosis and protection features
•
Pulse width modulator to implement a dimming function with reduced color shifting
•
Spread spectrum modulator to improve the EMI performance
Scope and purpose
Scope of this user manual is to provide instructions on the use of TLD5099EP voltage-mode boost to ground
evaluation board.
Intended audience
This document is intended for engineers who need to perform measurements and check performances with
TLD5099EP voltage-mode boost to ground evaluation board.
Table of contents
About this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2
Quick start procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
Auto-enable configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4
Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5
PCB layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6
Bill of material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7
Efficiency measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8
Maximizing efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
9
Minimizing EM emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
User guide
Please read the sections "Important notice" and "Warnings" at the end of this document
www.infineon.com
Rev.2.00
2022-02-04
Advertisement
Table of Contents
Related Manuals for Infineon TLD5099EP
Summary of Contents for Infineon TLD5099EP
-
Page 1: Table Of Contents
• Spread spectrum modulator to improve the EMI performance Scope and purpose Scope of this user manual is to provide instructions on the use of TLD5099EP voltage-mode boost to ground evaluation board. Intended audience This document is intended for engineers who need to perform measurements and check performances with TLD5099EP voltage-mode boost to ground evaluation board. -
Page 2: Description
TLD5099EP 1 Description Description The Evaluation board for medium power application with TLD5099EP configured in voltage-mode boost to ground topology will be explained. It can be implemented as a DC-DC power supply with constant voltage output. The default configuration of the board is voltage-mode boost to ground topology without any additional features enabled. - Page 3 Voltage-mode boost to ground evaluation kit TLD5099EP 1 Description Figure 2 Simplified schematic Table 1 Performance summary Parameter Conditions Value Input supply voltage Parameter degradation below 6.5 V 8 V to 27 V Down to 6.5 V for less than 2 s...
-
Page 4: Quick Start Procedure
Voltage-mode boost to ground evaluation kit TLD5099EP 2 Quick start procedure Quick start procedure The default configuration of the board has all additional features disabled. The jumper is placed in position 1-2. In this configuration the ENABLE signal must be applied on X18 (max. 45 V). If another output voltage... -
Page 5: Auto-Enable Configuration
Voltage-mode boost to ground evaluation kit TLD5099EP 3 Auto-enable configuration Auto-enable configuration By placing the jumper X5 on position 2-3, the device starts without any external enable signal because pin EN (ENABLE) is connected directly to the positive rail (see Schematics for details). -
Page 6: Schematics
Voltage-mode boost to ground evaluation kit TLD5099EP 4 Schematics Schematics Figure 5 Input filter User guide Rev.2.00 2022-02-04... - Page 7 Voltage-mode boost to ground evaluation kit TLD5099EP 4 Schematics Figure 6 Main power User guide Rev.2.00 2022-02-04...
-
Page 8: Pcb Layout
Voltage-mode boost to ground evaluation kit TLD5099EP 5 PCB layout PCB layout Figure 7 PCB layout top view Figure 8 PCB layout bottom view User guide Rev.2.00 2022-02-04... -
Page 9: Bill Of Material
Voltage-mode boost to ground evaluation kit TLD5099EP 6 Bill of material Bill of material Table 2 Bill of material Designator Value Manufacturer Manufacturer order number C1, C2, C6, C7, C19 10 uF Murata GCM32EC71H106KA03 C9, C26, C36 100 nF 06035C104K4Z2A... -
Page 10: Efficiency Measurements
Voltage-mode boost to ground evaluation kit TLD5099EP 7 Efficiency measurements Efficiency measurements Figure 9 Efficiency vs. input voltage This efficiency performance has been obtained with: Table 3 Parameters influencing efficiency Output load 139 Ω power resistor EMI filter Totally bypassed by closing the jumpers X1, X14 and X16... -
Page 11: Maximizing Efficiency
Voltage-mode boost to ground evaluation kit TLD5099EP 8 Maximizing efficiency Maximizing efficiency This evaluation board has been designed to reach a fair compromise between efficiency performance and EM emissions compliance. Nevertheless, if the maximum efficiency is needed, the following actions are suggested:... -
Page 12: Minimizing Em Emissions
Voltage-mode boost to ground evaluation kit TLD5099EP 9 Minimizing EM emissions Minimizing EM emissions This evaluation board has been designed to reach a fair compromise between efficiency performance and EM emissions compliance. Furthermore, this evaluation board can fulfill the class V of the CISPR25 in conducted emissions from 150 kHz to 108 MHz. -
Page 13: Revision History
Voltage-mode boost to ground evaluation kit TLD5099EP Revision history Revision history Document Date of release Description of changes version Rev.2.00 2022-02-04 Second release related to evalboard S01_P01 • Editorial changes and rephrasing for clarity • Updated all figures • Rearranged connectors on evalboard •... -
Page 14: Disclaimer
Infineon Technologies, All Rights Reserved. information given herein in the real application. Infineon Technologies’ products may not be used in Infineon Technologies hereby disclaims any and all any applications where a failure of the product or warranties and liabilities of any kind (including without...