Novexx Solutions DPM User Manual
  1. Manuals
  2. Brands
  3. Novexx Solutions Manuals
  4. Printer
  5. DPM
  6. User manual

Novexx Solutions DPM User Manual

Hide thumbs Also See for DPM:
Table of Contents

Advertisement

Quick Links

Download this manual
01/15 Rev. 02
Setup
Winding patterns ........................................... 2
DPM .......................................................... 2
PEM .......................................................... 3
Selecting the printing material ....................... 4
Label material ............................................ 4
Thermal transfer ribbon ............................. 5
Inserting label material .................................. 6
DPM .......................................................... 7
PEM .......................................................... 9
USER MANUAL
DPM - PEM
Inserting the ribbon ......................................10
Removing spent ribbon ............................10
Inserting a new ribbon roll ........................11
Settings .......................................................12
Ribbon tension .........................................12
Label sensor ............................................13
(DPM) Dispensing edge ...........................15
(DPM) Dispenser parameters ..................15
Material Parameters ................................16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DPM and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Novexx Solutions DPM

Summary of Contents for Novexx Solutions DPM

  • Page 1: Table Of Contents

    Label material ..........4 Label sensor ..........13 Thermal transfer ribbon ......5 Adjustment button for printhead pressure 14 Inserting label material ........6 (DPM) Dispensing edge ......15 DPM ............7 (DPM) Dispenser parameters ....15 PEM ............9 Material Parameters ........16...

  • Page 2: Winding Patterns

    („ribbon“) through the two types of print modules.  Only specially trained staff to insert and change the ribbons and material. [1] Material and ribbon path in the DPM (left version). Names of parts: No. Name No. Name...

  • Page 3: Pem

    01/15 Rev. 02 USER MANUAL Winding patterns DPM ‒ PEM [2] Material and ribbon path in the PEM (left version) Names of parts No. Name No. Name Adjustment knob for printhead Adjustment wheel for label sensor pressure Ribbon rewinding mandrel...

  • Page 4: Selecting The Printing Material

    DPM ‒ PEM Selecting the printing material Thermal transfer / direct thermal printing DPM and PEM print modules can print onto label material using the direct thermal mode or thermal transfer mode. Direct thermal Direct thermal printing is done without ribbon. The direct thermal process requires la- bel material with a temperature-sensitive coating.

  • Page 5: Thermal Transfer Ribbon

    01/15 Rev. 02 USER MANUAL Selecting the printing material DPM ‒ PEM Thermal transfer ribbon The following is recommended for thermal transfer ribbons: • The back of the ribbon should be coated so that it produces no static or friction ( •...

  • Page 6: Inserting Label Material

    During operation, the printhead can become hot. Be careful when touching the printhead!  Label material must be fed to the DPM/PEM using the equipment in which the module has been installed. This also applies to rewinding the backing paper (DPM).

  • Page 7: Dpm

    01/15 Rev. 02 USER MANUAL Inserting label material DPM ‒ PEM 1. Open the rear hood. 2. Adjusting the material guide to fit the width of the la- bel material. To do this, release the thumb screw [3A] on the outer side of the material guide, slide the material guide [3B] across at right angles to the feed direction and retighten the thumb screw.
  • Page 8 01/15 Rev. 02 USER MANUAL Inserting label material DPM ‒ PEM 5. Peel off about 50cm of labels from the backing paper [6]. [6] Peeling off labels from the backing paper. 6. Open the pressure lever [7A]. To do this, push the lever downwards.

  • Page 9: Pem

    01/15 Rev. 02 USER MANUAL Inserting label material DPM ‒ PEM 1. Open the hood. 2. Adjust the material guide to fit the width of the label material. To do this, release the thumb screw [10A] on the outer side of the material guide, slide the ma- terial guide [10B] to the material edge and retighten the thumb screw.

  • Page 10: Inserting The Ribbon

    Skip this section if you intend to print directly onto thermal material.  The pictures in this section show a DPM, but are also valid for a PEM. For information on choosing a suitable thermal transfer ribbon, refer to chapter Selecting the printing material ...

  • Page 11: Inserting A New Ribbon Roll

    01/15 Rev. 02 USER MANUAL Inserting the ribbon DPM ‒ PEM Inserting a new ribbon roll 1. Open the hood. 2. Put the ribbon roll on the lower right ribbon mandrel [12C]. Put an empty take-up sleeve on the upper left ribbon mandrel.

  • Page 12: Settings

    01/15 Rev. 02 USER MANUAL Settings DPM ‒ PEM Settings Ribbon tension To achieve an optimal print result, the ribbon has to run without creases. This is achieved by correctly setting the torque for the rewinding mandrel and the braking torque for the unwinding mandrel.

  • Page 13: Label Sensor

    01/15 Rev. 02 USER MANUAL Settings DPM ‒ PEM Label sensor The DPM/PEM modules are equipped with different sensors for punch recognition: • DPM: Transmission sensor • PEM: Combination of transmission and reflex sen- Setting the label sensor Turning the red adjustment wheel [17B] moves the sen- sor up to 80 mm (4“/5“...

  • Page 14: Adjustment Button For Printhead Pressure

    01/15 Rev. 02 USER MANUAL Settings DPM ‒ PEM Adjustment button for printhead pressure The material width and / or material thickness influence the pressure applied by the thermal transfer printhead on the feed roller. There are three possible settings for pressure [20]: •...

  • Page 15: (Dpm) Dispensing Edge

    01/15 Rev. 02 USER MANUAL Settings DPM ‒ PEM (DPM) Dispensing edge  Only for DPM. By inclining the dispensing edge, the dispensing posi- tion can be fine adjusted without having to change the machine position: 1. Undo the screws [21B] on both of the side mounting plates.

  • Page 16: Material Parameters

    01/15 Rev. 02 USER MANUAL Settings DPM ‒ PEM Material Parameters Using the following three parameters, you can tell the DPM/PEM how you want the labelling material to be processed: • PRINT PARAMETERS > Materialtype Sets material type (punched or endless). •...

This manual is also suitable for:

Pem

Table of Contents