Contents 1. Preface 7. Maintenance procedures 2. Description 8. Storing the generating set 3. Preparation before use 9. Troubleshooting 4. Using the generator set 10. Specifications 5. Safety features 11. Cable sizes 6. Maintenance schedule 12. EC Declaration of conformity 1.
Page 6
1.3.2 General advice When the generating set is received, check that it is complete and not damaged in any way (the photos shown in this manual do not have any contractual value). A generating set should be handled gently and brusque movements should be avoided. Ensure that the place where it is to be stored or used is carefully prepared beforehand.
Page 7
1.3.4 Safety guidelines to prevent fire Never operate the generating set in areas containing flammable products (risk of sparks). Keep all flammable products (petrol, oil, fabric etc.) out of the way when the unit is in operation. Never cover the generating set with any type of material while it is in operation or just after Danger it has been turned off: always wait until the engine cools down.
1.3.12 Safety guidelines for handling batteries Never leave the battery close to a flame or fire. Use only insulated tools. Never use sulphuric acid or acid water to top up the electrolyte level. Danger 2. Description Figure A Earth connection Air filter Electrical sockets Oil filler gauge plug...
3.4. Checking the fuel level Filling up with fuel must be carried out when the engine is stopped and in accordance with safety instructions (see. § Filling with fuel). Danger Unscrew the fuel tank cap (fig. A - No. 4). Visually check the level of fuel.
4.2. Operation When the running speed of the generating set has stabilised (approximately 3 minutes): Check that the circuit breakers (fig. A - No. 10) are pushed down. Press if necessary. Connect the appliances that are to be used to the electrical sockets (fig. A - No. 11) of the generating set. The working hours counter (fig.
7. Maintenance procedures 7.1. Checking bolts, nuts and screws To prevent faults or breakdowns, carefully check all the nuts, bolts and screws on a daily basis. Inspect the entire generating set before and after each use. Tighten any loose nuts or bolts. Danger: The cylinder head bolts must be tightened by a specialist.
7.5. Cleaning the spark arrester Undo the mounting nuts (diag. E – no. 1) and remove the exhaust silencer (diag. E – no. 2). Undo the mounting bolts on the exhaust silencer guard (diag. E – no. 3) and remove the exhaust silencer guard (diag. E – no. 6). Undo the mounting bolts on the spark arrester (diag.
9. Troubleshooting Problems Probable causes Possible solutions Load connected to the generating set during start-up. Disconnect the load. Check the oil level and top up if necessary Oil level too low. (see § Checking the oil level). Unsuitable fuel. Change the fuel (see § Specifications). Fuel level too low.
SDMO Industries - 12 bis rue de la Villeneuve - CS 92848 - the technical file 29228 BREST Cedex 2 – France. G. Le Gall - SDMO Industries - 12 bis rue de la Villeneuve - CS 92848 - 29228 BREST Cedex 2 – France. Product description :...
Page 15
а и 8. Х 4. Э 10. Х 1.1. 1.2. 1 – 2 – 3 – 1.3. 1.3.1 Э Э Э...
Page 21
7.1. 7.2. . § . 4), . § Х . § 7.3. . A – . 14) . A – . 5). . C, . 1). . C – . 2), . C – . 3) – . 4). 7.4. .
Page 22
7.5. . E, . 1) . E, . 2). . E, . 3) . E, . 6). . E, . 4). . E, . 5). 7.6. . 1) . 2). «X» 0,7 - 0,8 1/8 - 1/4 7.7. 8. Х .
Page 23
В . § . § Х . § . 5) . § . 6) . § . 2) . § . § . § . 10) . 11) § . 13) 10. Х HX 7500 T AVR IP54 6000 W / 4800 W (LpA) Honda GX 390 6,1 L...
Page 24
SDMO Industries - 12 bis rue de la Villeneuve - CS 92848 - 29228 BREST Cedex 2 – France. G. Le Gall - SDMO Industries - 12 bis rue de la Villeneuve - CS 92848 - 29228 BREST Cedex 2 – France.