Related Manuals for SDMO BOOSTER 2000 UK
Summary of Contents for SDMO BOOSTER 2000 UK
-
Page 1: Maintenance Manual
BOOSTER 2000 UK GENERATING SET USER MAINTENANCE MANUAL Réf. GPAO 33522111701 Réf. Const. 5490 326 5000... - Page 2 Réf. GPAO 33522111701 Réf. Const. 5490 326 5000...
- Page 3 Réf. GPAO 33522111701 Réf. Const. 5490 326 5000...
- Page 4 Réf. GPAO 33522111701 Réf. Const. 5490 326 5000...
-
Page 5: Table Of Contents
You can contact us with any comments or suggestions at: fax: technical documentation department, number: + 00 33 (0)2 98 41 16 12 by e-mail: doctech@sdmo.com 1.2. Pictograms and plates on the generating sets and what they mean Danger... - Page 6 A = Generating set model G = Fuse rating B = Generating set output H = Generating set C = Voltage noise output D = Amperage I = Generating set earth E = Current frequency J = Reference Standard F = Power factor K = Serial number Example of an identification plate 1.3.
- Page 7 Before use, it is essential that you know how to stop the generating set immediately and that you thoroughly understand all the controls and operations. Warning Never let other people use the generating set without giving them all necessary instructions beforehand. Never let children touch the generating set, even when it is not in operation.
- Page 8 1.3.6 Filling with fuel fuel highly flammable vapours combustible. Smoking, using a naked flame or producing sparks are forbidden while the fuel tank is being filled. Filling should be carried out with the motor turned off. All traces of fuel should be wiped off Danger with a clean cloth.
-
Page 9: General Description
2. General description 2.1. Description of the generating set (diagram A) Starter (No. 1) Starter – reel winder (No. 2) Fuel tap (No. 3) Earth connection (No. 4) Fuel tank cap (No. 5) Starter key (No. 6) Enclosure (No. 7) Exhaust silencer (No. -
Page 10: Using The Generator Set
4. Using the generator set Do not run the generating set if the enclosure is not in place. Never take the enclosure off, if the generating set is running Danger 4.1. Starting procedure (A and D diagrams) ❶ Check that the earth wire is properly connected to the bolt (No. 4, fig. A) ❷... -
Page 11: Protective Devices
5. Protective devices (if fitted, see specifications table) 5.1. Oil failure cut-out This mechanism is designed to prevent any damage to the engine resulting from lack of oil in the engine sump. It stops the engine automatically (in this case, the red oil level warning light is turned on and stops the starting process). -
Page 12: Maintenance Procedures
7. Maintenance procedures Stop the motor before carrying out any maintenance procedure. To make allowances for any accidental spillage, switch off the motor ignition and disconnect the spark plug cap(s). Only use original parts or equivalent. The use of spare parts of a different quality can damage the generating set. -
Page 13: Storing The Generating Set
8. Storing the generating set Generating sets, which are to remain unused during a long period of time must undergo certain procedures, in order to keep them in good condition. Check that the storage area is not dusty or humid. Clean the outside of the generating set and apply a rustproofing product 8.1. -
Page 14: Specifications
10. Specifications Model BOOSTER 2000 Engine type Honda GX 100 Output 50 Hz (watts) 1700 Maximum output 50 Hz (KVA) cos ϕ 0.8 Alternating current (voltage and amperage) 230 V – 7.4 A Direct current (voltage and amperage) 12 V – 8.3 A maxi Circuit breaker ●... -
Page 15: Warranty Conditions
12. Warranty conditions Faults covered by the guarantee. GENERATING SET The supplier undertakes to rectify all operating problems resulting from defects in design, materials and workmanship. This obligation does not apply to damage resulting from materials supplied by, or adjustments made by the buyer. -
Page 16: Declaration Of Conformity
13. E.C. Declaration of conformity We, SDMO, 12 bis rue de la Villeneuve, CS 92848, 29228 BREST CEDEX 2, declare that generating sets of the type: “BOOSTER 2000“ satisfy the conditions of the following EC Council Directives: Machine directive 98/37/EEC of 22nd June 1998.