Hide thumbs Also See for GARUDAN GF-1107-147 MH:
Table of Contents

Advertisement

Quick Links

Instructions for use
GF-1107-147 MH
ANITA B, SRO
Průmyslová 2453/7
680 01 Boskovice
Czech Republic
tel: + 420 516 454 774
+420 516 453 496
fax: +420 516 452 751
e-mail:
info@anita.cz
MP02300EN_220518

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GARUDAN GF-1107-147 MH and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Anita GARUDAN GF-1107-147 MH

  • Page 1 Instructions for use GF-1107-147 MH ANITA B, SRO Průmyslová 2453/7 680 01 Boskovice Czech Republic tel: + 420 516 454 774 +420 516 453 496 fax: +420 516 452 751 e-mail: info@anita.cz MP02300EN_220518...
  • Page 2 18/05/2022 Doubek Lumír All rights reserved. Owned by Anita B s ro and protected by copyright. Use of this content without the written permission of Anita B s ro is prohibited.Copyright © Anita B s ro (201 7) GF-1107-147 MH...
  • Page 3: Table Of Contents

    ANITA © Content A.BASIC INFORMATION……………………………………………………………………5 A.1 Brief description and intended use of the sewing machine ..........5 A.2 Technical parameters ....................... 6 B.SECURITY MEASURES AND SECURITY FEATURES ........... 7 B.1 General safety instructions ....................7 B.2 Safety instructions on delivery ..................7 B.3 Safety instructions for installation and maintenance ............
  • Page 4 ANITA © E.8 Thread trimming settings ....................26 E.9 Feeder settings ....................... 27 E.9.1 Feeder height adjustment ..................27 E.9.2 Feeder tilt adjustment ....................27 E.9.3 Adjusting the feed cams ..................28 E.10 Adjusting the presser foot pressure and stroke height ..........29 F.
  • Page 5: A.basic Information

    ANITA © A. BASIC INFORMATION A.1 Brief description and intended use of the sewing machine Single-needle flat machine with bottom immersion and needle feed. The machine is equipped with a horizontally mounted, standard hook (21 mm spool). Integrated quiet and economical servomotor and LED lighting.
  • Page 6: Technical Parameters

    ANITA © A.2 Technical parameters Model GF-1107-147 MH Number of needles Medium to heavy materials Type of stitch Bound double Stitch length 4 mm Lift the foot with the hand 7 mm lever Lift the foot with the knee 11 mm...
  • Page 7: B.security Measures And Security Features

    ANITA © B. SECURITY MEASURES AND SECURITY FEATURES B.1 General safety instructions Read this manual, the operating instructions and the operating instructions carefully before using the machine. It also lists the machine parameters and specifies the limits and conditions under which the machine may be used.
  • Page 8: Safety Instructions During Daily Operation For The Operator

    Protect the control box or motors from splashes of liquids. B.7 Instructions for disposing of the machine At the end of the technical service life of the machine, hand it over for disposal to ANITA B, sro or another company dealing with professional disposal of products.
  • Page 9: Putting The Machine Into Operation

    ANITA © C. PUTTING THE MACHINE INTO OPERATION C.1 Oil pan installation Giant. No. 1 Insert the rubber corners ① and ③ into the plate cut-out (larger towards the operator, smaller from the operator). Giant. No. 2 Insert the entire oil sump into the plate cut-out.
  • Page 10: Adjusting The Foot Lift Height Using The Knee Lever

    ANITA © C.2 Adjusting the foot lift height using the knee lever Warning: Caution, risk of injury: switch off the main when adjusting the machine switch. 1. The standard stroke of the foot using the knee lever is 10 mm.
  • Page 11: Adding Oil

    ANITA © C .4 Adding oil Warning: Caution, risk of injury: switch off the main switch when adjusting the machine. Fill the hook lubrication oil reservoir before starting the machine. 1. Lower the machine head and support it with the foot lift solenoid against the plate.
  • Page 12: Adjusting The Hook Lubrication

    ANITA © C .4.1 Adjusting the hook lubrication Warning: Caution, risk of injury: switch off the main switch when adjusting the machine. The oil level in the hook is set with the screw①. Setting procedure: If you tighten screw ① (turn the screw clockwise), the amount of oil in the hook will increase . If you turn the screw counterclockwise, the amount of oil in the hook will decrease .
  • Page 13: Adjusting The Oil Quantity

    ANITA © C .4.2 Adjusting the oil quantity C.4.2.1 Verification of the quantity of oil supplied a) After running the machine idle for three minutes, place the control paper under the machine hook, and start the machine for 5 seconds. You can then check the amount of oil supplied.
  • Page 14: Inserting The Needle

    ANITA © C.5 Inserting the needle Warning: Caution, risk of injury: switch off the main when adjusting the machine switch. The machine uses a 134 system needle (DPx5). Select the needle size according to the thread strength used and the type of material.
  • Page 15: Stitch Length Adjustment

    ANITA © C .7 Stitch length adjustment 1. Select the stitch length on the machine arm using the ① dial in the direction of the arrow. The required value must overlap with dot A. 2. Values are given in mm.
  • Page 16: Lowering The Lower Thread

    ANITA © C .10 Lowering the lower thread 1. Insert the spool into the winder ①, insert the spool until it moves on. 2. Thread the lower thread, pull it out of the bobbin to the right side of the stand thread. Then turn the end of the spool clockwise several times.
  • Page 17: Thread Tension

    ANITA © C .11 Thread tension C.11.1 Setting the upper thread tension 1. Turn the tensioner ①clockwise (in direction A) to make the thread shorter. 2. Turning the tensioner ① counterclockwise (in direction B) will make the thread longer. 3. By turning the tensioner ② clockwise (direction C), the thread tension will be greater.
  • Page 18: Threading

    ANITA © C .12 Threading C.12.1 Thread tension change 1. Loosen screw ②. 2. By turning screw ③ clockwise (direction A), the thread tension increases . 3. Turn ③ counterclockwise (direction B) to reduce the voltage . C.12.2 Adjusting the stiffness of the thread tension compensating spring 1.
  • Page 19: Thread Guide Adjustment

    ANITA © C .13 Thread guide adjustment Warning: Caution, risk of injury: switch off the main switch when adjusting the machine. MP02300EN_220518 GF-1107-147 MH...
  • Page 20: Adjusting The Needle Position When Stopped

    ANITA © C .14 Adjusting the needle position when stopped Warning: Caution, risk of injury: switch off the main when adjusting the machine switch. C.14.1 Stop position after thread cutting . When the needle stops in the upper position, the thread lever must be in the highest position.
  • Page 21: Lubrication

    ANITA © D. LUBRICATION Warning: To prevent an accident, turn off the power before starting work. Plug Z : continuously check the oil level on the U indicator located on the right side of the stand head. The minimum and maximum amounts of oil are shown here.
  • Page 22: Configuration Of Machine

    ANITA © E. _ CONFIGURATION OF MACHINE E.1 Pedal adjustment Warning: To prevent an accident, turn off the power before starting work. E.1.1 Engine rod installation Move the pedal (3) to the right or left as shown by the arrows. Engine Speed Sensor Lever (1) and the rod (2) should be perpendicular to the pedal.
  • Page 23: Pedal Function

    ANITA © E.1.3 Pedal function The pedal is operated in the following four steps: 1. If you depress the front of the pedal lightly, the machine will run at low speed (B). 2. If you depress the front of the pedal hard, the machine will run at high speed (A).
  • Page 24: Inserting The Needle

    ANITA © E.3 Inserting the needle Insert the needle (1) into the hole in the needle bar with the groove on the left. Push the needle as far as it will go. Finally, tighten the screw (3). (Fig. No. 30) E.4 Needle bar height adjustment...
  • Page 25: Replacing The Fixed And Movable Knife

    ANITA © E.7 Replacing the fixed and movable knife E.7.1 MOVABLE KNIFE REPLACEMENT Turn the handwheel to bring the needle to the top dead center. Remove the stitch plate and the two screws (2). Install a new knife (1), tighten the screws (2) and the stitch plate. (Fig. 33) E.7.2 FIXED KNIFE REPLACEMENT...
  • Page 26: Thread Trimming Settings

    ANITA © E.8 Thread trimming settings Warning: Caution, risk of injury: switch off the main when adjusting the machine switch. 1. Turn the handwheel until the thread lever is in the lowest position, at which point the solenoid (4) must slide the guide with the roller (3) into the recess in the cam. If not, loosen the screws (2) and perform the correct timing.
  • Page 27: Feeder Settings

    ANITA © E.9 Feeder settings E.9.1 Feeder height adjustment After loosening the screw (2) and turning the sleeve (1), you can adjust the height of the feeder. When the maximum stitch length is set and the feeder is in the highest position, the standard height from the surface of the stitch plate to the top of the feeder is 0.6 mm - 0.7...
  • Page 28: Adjusting The Feed Cams

    ANITA © E.9.3 Adjusting the feed cams Warning: Caution, risk of injury: switch off the main when adjusting the machine switch. Use screws ① and ② to adjust the feeder ellipse. Follow indicators ③ and ④. The ideal ellipse is at point 0.
  • Page 29: Adjusting The Presser Foot Pressure And Stroke Height

    ANITA © E.10 Adjusting the presser foot pressure and stroke height Warning: To prevent an accident, turn off the power before starting work. A. As shown in Figure 35, remove the rubber cover (2) from the front cover (1). Then lower the foot (3) onto the stitch plate.
  • Page 30 ANITA © E.11 Changing the type of administration Model GF-1107-147 MH allows you to set two ways of feeding material: 1) feeder and needle (bottom immersion and needle feed) This is how the machine is delivered from our factory. This method of administration is suitable for sewing medium or thick materials, or in case the materials slide one after the other.
  • Page 31: Machine Handling

    ANITA © F. MACHINE HANDLING CAUTION when carrying or positioning the sewing machine. If you need to move the machine head, always do it in two people. Prepare a clean, level and firm surface for the machine. Do not place the machine on the edge of the table, there is a risk of falling.
  • Page 32: Instructions For The Drive Unit

    15. Do not operate the machine in a dusty environment or in an environment that is prone to corrosion. Disposal instructions At the end of the technical service life of the power unit, hand it over for disposal to ANITA B, sro or another company dealing with professional disposal of products. GF-1107-147 MH...
  • Page 33: Using The Control Panel

    ANITA © G.3 Using the control panel • Sections A, B, C, D, E, F, G, H: increase the number of stitches set Increase the • Increase the parameter number when selecting a parameter value • Increase the value when setting the parameter value •...
  • Page 34 ANITA © After depressing the pedal, the machine jams and cuts D times (max. 15 times). To interrupt the action, depress the heel pedal. To set the D Barring value, press the key 1. When pressed, the machine will sew sections E, F, G, H.
  • Page 35 ANITA © Activation,,, signaled by individual LEDs above the display, the order of the LEDs corresponds to the order of the buttons . MP02300EN_220518 GF-1107-147 MH...
  • Page 36: Setting User Parameters

    ANITA © G. 4 Setting user parameters If the control panel is in the default state, press the P key , which is used to enter the parameter settings. + Keys and - used to select parameters. S key used to enter individual parameters and set their value.
  • Page 37 ANITA © Default Parameter Parameter function Range Description settings End suture run mode Not used with GF-1107, applies to other models selection Pedal position to start sewing Stop pedal position 30-1000 Service settings - do not change Pedal stroke pedal position...
  • Page 38 ANITA © Default Parameter Parameter function Range Description settings N01 Control system version N02 Operator panel version N03 Speed N04 Pedal AD Information display N05 Angle of rotation (upper position) N06 Angle of rotation (lower position) N07 AD voltage N12 Knee lever sensor position AD...
  • Page 39: List Of Error Messages

    ANITA © G. 5 List of error messages Code Description of the problem Solution Power failure: Current overload or too high voltage Switch off the machine and check the mains voltage. If the error persists, replace the control box or call Power failure: for service.
  • Page 40: Spare Parts Catalog

    ANITA © H. SPARE PARTS CATALOG H.1 MACHINE FRAME & MISCELLANEOUS COVER COMPONENTS (1/2) GF-1107-147 MH MP02300EN_220518...
  • Page 41 ANITA © H. 1 MACHINE FRAME & MISCELLANEOUS COVER COMPONENTS (1/2) REF. NO PART. NO NAME OF THE PART 20003404 Side plate 10008972 Screw SM3 / 16 "x28 L = 10 10022343 Arm Thread Guide 10008972 Screw SM3 / 16 "x28 L = 10...
  • Page 42 ANITA © H. 1 MACHINE FRAME & MISCELLANEOUS COVER COMPONENTS (2/2) GF-1107-147 MH MP02300EN_220518...
  • Page 43 ANITA © H. 1 MACHINE FRAME & MISCELLANEOUS COVER COMPONENTS (2/2) REF. NO PART. NO NAME OF THE PART 10012136 Rubber Plug 10012139 Rubber Ring 10012141 Air- discharging 10012867 Thread Tension Guide 10011313 Screw M6x12 10022344 Reverse Feed Solenoid Base...
  • Page 44 ANITA © H.2 MAIN SHAFT & THREAD TEKE-UP COVER COMPONENTS GF-1107-147 MH MP02300EN_220518...
  • Page 45 ANITA © H. 2 MAIN SHAFT & THREAD TEKE-UP COVER COMPONENTS REF. NO PART. NO NAME OF THE PART 10012613 Coupling 10009187 Screw 10011227 Rubber ring 10012615 Coupling 10038017 Engine 10006157 Screw ASM. 10002436 Screw 20010974 Head wheel ASM. 10012497...
  • Page 46 ANITA © H. 3 HORIZONTAL FEED & VERTICAL FEED AND HOOK DRIVING SHAFT COMPONENTS (1/2) GF-1107-147 MH MP02300EN_220518...
  • Page 47 ANITA © H. 3 HORIZONTAL FEED & VERTICAL FEED AND HOOK DRIVING SHAFT COMPONENTS (1/2) REF. NO PART. NO NAME OF THE PART 10012490 10012540 Feed bar driving crank 10010074 Screw 10010095 Screw 10012531 Feed bar ASM. 10022849 Feed dog...
  • Page 48 ANITA © H. 3 HORIZONTAL FEED & VERTICAL FEED AND HOOK DRIVING SHAFT COMPONENTS (2/2) GF-1107-147 MH MP02300EN_220518...
  • Page 49 ANITA © H. 3 HORIZONTAL FEED & VERTICAL FEED AND HOOK DRIVING SHAFT COMPONENTS (2/2) REF. NO PART. NO NAME OF THE PART 10005740 Eccentric drive _ cam 10010678 Screw 10012462 Gear 10008862 Screw 10012489 Feed driving shaft 10012533 Oil seal...
  • Page 50 ANITA © H. 4 HANG LIFTER & TENSION RELEASE COMPONENTS GF-1107-147 MH MP02300EN_220518...
  • Page 51 ANITA © H. 4 HANG LIFTER & TENSION RELEASE COMPONENTS REF. NO PART. NO NAME OF THE PART 10006112 Presser foot ASM. 10010650 Screw 10014141 Bearing support 10013328 Presser bar 10013567 Screw SM11 / 64 "x 40 L = 15.8 10011887 Screw SM9 / 64 "x 40 L = 4...
  • Page 52 ANITA © H.5 THE NEEDLE BAR SWING COMPONENTS GF-1107-147 MH MP02300EN_220518...
  • Page 53 ANITA © H. 5 THE NEEDLE BAR SWING COMPONENTS REF. NO PART. NO NAME OF THE PART 10022509 Rocking base compl . 10022340 Bushing 10023449 Slide block guide 10003549 Bearing 10014395 Screw M4 × 14 10023454 Driving link 10022856 Link pin...
  • Page 54 ANITA © H. 6 FEED ADJUST MECHANISM COMPONENTS GF-1107-147 MH MP02300EN_220518...
  • Page 55 ANITA © H. 6 FEED ADJUST MECHANISM COMPONENTS REF. NO PART. NO NAME OF THE PART 10013870 10012459 Connecting pin 10013590 Screw 10010092 Screw 10012634 Connecting plate 10012681 Crank 10012629 Shaft sleeve 10012622 Oil seal 10003921 Screw 10012627 Closing ring...
  • Page 56 ANITA © H. 7 PRESSER FOOT COMPONENTS OF OIL PLATE KNEE LIFT GF-1107-147 MH MP02300EN_220518...
  • Page 57 ANITA © H. 7 PRESSER FOOT COMPONENTS OF OIL PLATE KNEE LIFT REF. NO PART. NO NAME OF THE PART 10012632 Oil reservoir 10012631 Knee lifter presser rod 10013102 Head Gasket 10002562 Bracket ASM. 10003896 Bracket 10002610 Screw 10002613 Screw 10024632 Connecting Rod ASM.
  • Page 58 ANITA © H.8 BOBBIN WINDER COMPONENTS GF-1107-147 MH MP02300EN_220518...
  • Page 59 ANITA © H. 8 BOBBIN WINDER COMPONENTS REF. NO PART. NO NAME OF THE PART 10013875 Bobbin winder ASM. 10008773 Rubber ring 10004380 Screw 10013269 Screw 10011149 Thread cutter 10013064 Bobbin thread tension ASM. 10011158 Screw 10011200 Thread guide plate...
  • Page 60 ANITA © H.9 AUTOMATIC REVERSE FEED COMPONENTS GF-1107-147 MH MP02300EN_220518...
  • Page 61 ANITA © H. 9 AUTOMATIC REVERSE FEED COMPONENTS REF. NO PART. NO NAME OF THE PART 10008934 Screw 10038021 Option Switch ASM. 10034506 ASM electromagnet. 10012142 Screw 10012587 Washer 10012628 Crank Pin 10013538 Screw MP02300EN_220518 GF-1107-147 MH...
  • Page 62 ANITA © H.10 THREAD STAND COMPONENTS GF-1107-147 MH MP02300EN_220518...
  • Page 63 ANITA © H.10 THREAD STAND COMPONENTS REF. NO PART. NO NAME OF THE PART 10007130 Thread Stand ASM. 10004282 Column Cap 10004293 Column Pipe ( Upper ) 10003301 Screw M5x14 10003022 Washer 10002953 Nut M5 10004289 Thread Guide Pipe 10004285...
  • Page 64 ANITA © H. 11 WIPER COMPONENTS GF-1107-147 MH MP02300EN_220518...
  • Page 65 ANITA © H. 11 WIPER COMPONENTS REF. NO PART. NO NAME OF THE PART 10034507 Wiper ASM. 10012631 Screw MP02300EN_220518 GF-1107-147 MH...
  • Page 66 ANITA © H.12 THREAD TRIMMER COMPONENTS (ROTATION KNIFE) (1/2) GF-1107-147 MH MP02300EN_220518...
  • Page 67 ANITA © H. 12 THREAD TRIMMER COMPONENTS (ROTATION KNIFE) (1/2) REF. NO PART. NO NAME OF THE PART 10011422 Screw SM 9/6 4 "× 40 L = 4 10011421 Fixed Knife 10011497 Screw SM11 / 64 "× 40 L = 9...
  • Page 68 ANITA © H.12 THREAD TRIMMER COMPONENTS (ROTATION KNIFE) (2/2) GF-1107-147 MH MP02300EN_220518...
  • Page 69 ANITA © H. 12 THREAD TRIMMER COMPONENTS (ROTATION KNIFE) (2/2) REF. NO PART. NO NAME OF THE PART 10011605 Screw SM1 / 4 "x28 L = 12 10009471 Nut M4 10006131 Solenoid Base 10013046 Solenoid Connecting Shaft 10011845 Washer 10011606...
  • Page 70 ANITA © H. 13 OIL LUBRICATION COMPONENTS GF-1107-147 MH MP02300EN_220518...
  • Page 71 ANITA © H. 13 OIL LUBRICATION COMPONENTS REF. NO PART. NO NAME OF THE PART 10000569 Floater ASM. 10008777 O-ring 10008782 Floateer case 10013048 Pipe stopper 10007806 Oil pipe 10008772 Oil sight window 10008943 Rubber plug 10008780 Oil inlet 10007806...
  • Page 72 ANITA © H.14 ACCESSORIE PART COMPONENTS GF-1107-147 MH MP02300EN_220518...
  • Page 73 ANITA © H. 14 ACCESSORIE PART COMPONENTS REF. NO PART. NO NAME OF THE PART Accessory Bag Asm A 10012631 Knee Lifter Presser Rod 10004514 Rame Support Bar 10010995 Screw Driver, Middle 10013185 Screw Driver, Small 10005639 Needle Thread ASM Guide...

Table of Contents