Related Manuals for SHOWTEC Media Panel 100 CCT
Summary of Contents for SHOWTEC Media Panel 100 CCT
- Page 1 USER MANUAL ENGLISH Media Panel 100 CCT Product code: 33303 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
- Page 2 Media Panel 100 CCT Preface Thank you for purchasing this Showtec product. The purpose of this user manual is to provide instructions for the correct and safe use of this product. Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
-
Page 3: Table Of Contents
Media Panel 100 CCT Table of contents Introduction ................................4 Before Using the Product ..........................4 Intended Use ............................... 4 Product Lifespan ..............................4 LEDs Lifespan ............................... 4 Text Conventions ..............................5 Symbols and Signal Words ..........................5 Symbols on the Information Label ........................6 Safety .................................. - Page 4 Media Panel 100 CCT Disp Time (Display Time) ........................29 Information ..............................30 Fixture Hours ............................30 Version ..............................30 RDM ...............................30 DMX Channels ..............................31 1 Channel, 2 Channels, 3 Channels, 6 Channels, 9 Channels ............31 Troubleshooting ..............................32 Maintenance ..............................33 Preventive Maintenance ..........................33 Basic Cleaning Instructions ........................33...
-
Page 5: Introduction
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer. Your shipment includes: ● Showtec Media Panel 100 CCT ● Schuko to IEC power cable (1,5 m) ● Four-blade barndoor ●... -
Page 6: Text Conventions
Media Panel 100 CCT Text Conventions Throughout the user manual the following text conventions are used: ● Buttons: All buttons are in bold lettering, for example “Press the UP/DOWN buttons” ● References: References to chapters and parts of the device are in bold lettering, for example: “Refer to 2. -
Page 7: Symbols On The Information Label
Media Panel 100 CCT Symbols on the Information Label This product is provided with an information label. The information label is located on the backside of the device. The information label contains the following symbols: This device shall not be treated as household waste. -
Page 8: Safety
Media Panel 100 CCT Safety Important Read and follow the instructions in this user manual before installing, operating or servicing this product. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual. Warnings and Safety Instructions... - Page 9 Media Panel 100 CCT Attention General safety ● Do not connect the device to a dimmer pack. ● Do not switch the device on and off in short intervals. This decreases the device’s life. ● Do not shake the device. Avoid brute force when installing or operating the device.
-
Page 10: Requirements For The User
Media Panel 100 CCT Requirements for the User This product may be used by ordinary persons. Maintenance may be carried by ordinary persons. Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite dealer for more information. -
Page 11: Description Of The Device
Description of the Device The Showtec Media Panel 100 CCT is a bright 100 watt warm to daylight white video LED panel with a high 96 CRI and a beam angle of 120°, suitable for various studio and video applications. The stable and highly accurate colour temperature of 3000 K to 5600 K with a maximum output of 6650 lumen is ideally suited for bloggers, streamers and webinar presenters. -
Page 12: Back View
Media Panel 100 CCT Back View Fig. 03 05) LED Display 06) Dimmer control / Control Wheel 07) ON/OFF 08) 24 V DC power adapter IN 09) 5-pin DMX signal connector OUT 10) 5-pin DMX signal connector IN Product code: 33303... -
Page 13: Product Specifications
Media Panel 100 CCT Product Specifications Model: Media Panel 100 CCT Electrical: Input voltage: 24 V DC Input current: Power consumption: 100 W Physical: Dimensions: 487 x 337 x 55 mm (LxWxH) Weight: 2,6 kg Optics: Light source: 392x 0,5 W White LED Dimmer: 0–100 %... -
Page 14: Optional Accessories
Media Panel 100 CCT Optional Accessories The Media Panel is delivered with accessories. You can additionally purchase the following accessory: Product code: 33310 (Showtec A V-Mount Battery Holder is optional for mobile use) Dimensions Fig. 04 Product code: 33303... -
Page 15: Installation
Media Panel 100 CCT Installation Safety Instructions for Installation WARNING Incorrect installation can cause serious injuries and damage of property. If trussing systems are used, installation must be carried out only by instructed or skilled persons. Follow all applicable European, national and local safety regulations concerning rigging and trussing. -
Page 16: Rigging
Media Panel 100 CCT Rigging The device can be positioned on a flat surface or mounted to a truss or other rigging structure in any orientation. Make sure that all loads are within the pre-determined limits of the supporting structure. - Page 17 Media Panel 100 CCT To mount the device, follow the steps below: 01) Use a clamp to attach the device to the supporting structure, as shown in Fig. 05. Make sure that the device cannot move freely. 02) Secure the device with a secondary suspension, for example a safety cable. Make sure that the secondary suspension can hold 10 times the weight of the device.
-
Page 18: Angle Adjustment
Media Panel 100 CCT Angle Adjustment You can adjust the angle of the device with the adjustment screw (01). Turn the adjustment screw (01) counterclockwise to release it. 02) Tilt the device to the desired angle (see Fig. 07). 03) Turn the adjustment screw (01) clockwise to tighten it. Make sure that the device cannot move freely after the adjustment screw (01) is tightened. -
Page 19: Barndoor Installation
Media Panel 100 CCT Barndoor Installation The accessory frame is equipped with a spring-loaded clip. This prevents the barndoor from falling out. Install the barndoor frame (see Fig. 08). Hold the spring-loaded clip and pull it upwards on the top of the device and pull it downwards at the bottom (see Fig. -
Page 20: Free-Standing Bracket Installation
Media Panel 100 CCT Free-standing Bracket Installation Put the free-standing bracket on the Media Panel. Install all elements as shown in Fig. 11. Tighten the screws. Fig. 11 Connecting to Power Supply Attention Power supply This device falls under IEC protection class II. This device shall be connected to an external power supply. -
Page 21: Setup
Disconnect power supply before connecting or disconnecting data cables. Stand-alone Setup When the Media Panel 100 CCT is not connected to a controller or to other devices, it functions as a stand-alone device. It can be operated manually or in auto mode. -
Page 22: Dmx Cables
Fig. 12. Fig. 12 Master/Slave Setup The Media Panel 100 CCT supports master/slave control mode. To connect multiple devices in master/slave setup, follow the steps below: Connect the first device’s DMX OUT connector to the second device’s DMX IN connector. -
Page 23: Dmx Linking
04) Continue assigning the starting addresses of the remaining devices by adding each time 9 to the previous number. Make sure that you do not have any overlapping channels in order to control each Media Panel 100 CCT correctly. If two or more devices are addressed similarly, they will work similarly. -
Page 24: Operation
Media Panel 100 CCT Operation Safety Instructions for Operation Attention This device must be used only for the purposes it is designed for. This device is intended for professional use as an indoor spot. It is suitable only for indoor installation. -
Page 25: Control Panel
Use the Control Wheel to adjust settings in Knob mode. See 6.6.1. Knob Mode on page 26 for more information Start-up Upon start-up the display will show a splash screen with the logo of Showtec. Press any button to enter the password and/or enter the Main Menu. Note: ●... -
Page 26: Menu Overview
Media Panel 100 CCT Menu Overview Product code: 33303... -
Page 27: Main Menu Options
Media Panel 100 CCT Main Menu Options The main menu has the following options: Turn the Control wheel to navigate through the main menu. Press the Control wheel to open the submenus. Note: Some of the submenus require a password. The default password is: 1 1 1 1. Deactivating the display lock does not affect the submenu items which by default require a password. -
Page 28: Static
Media Panel 100 CCT Static In this menu, you can set the static colors to create an infinite range of colors. Turn the Control wheel to scroll through the static colors (WW, CW) and STROBE. Press the Control wheel to open the settings submenu. -
Page 29: Settings
Media Panel 100 CCT Settings In this menu you can adjust the device’s settings. This menu requires a password. The default password is: 1 1 1 1. Enter the password to access the menu. Press the Control wheel to confirm the password. -
Page 30: Dmx Error
Media Panel 100 CCT DMX Error In this submenu, you can determine the behavior of the device in case of a DMX failure. Select DMX ERROR and press the Control wheel to open the submenu. Turn the Control wheel to toggle between the following 2 options: ●... -
Page 31: Information
Media Panel 100 CCT Information In this menu you can view the total operation time, current software version and the RDM details of the device. Turn the Control wheel to choose FIXTURE HOURS, VERSION or RDM. Press the Control wheel button to confirm the selection. -
Page 32: Dmx Channels
Media Panel 100 CCT DMX Channels 1 Channel, 2 Channels, 3 Channels, 6 Channels, 9 Channels 1 CH 2 CH 3 CH 6 CH 9 CH Function Value Setting (UNO) (DOS) (VW.D) (VW.f) (STD.P) Master Dimmer 000–255 From low to high intensity (0–100 %) Dimmer Fine 000–255... -
Page 33: Troubleshooting
Media Panel 100 CCT Troubleshooting This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts. Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage. -
Page 34: Maintenance
Media Panel 100 CCT Maintenance Preventive Maintenance Attention Before each use, examine the device visually for any defects. Make sure that: ● All screws used for installing the device or parts of the device are tightly fastened and are not corroded. -
Page 35: Deinstallation, Transportation And Storage
Media Panel 100 CCT Deinstallation, Transportation and Storage Instructions for Deinstallation WARNING Incorrect deinstallation can cause serious injuries and damage of property. ● Let the device cool down before dismounting. ● Disconnect power supply before deinstallation. ● Always observe the national and site-specific regulations during deinstallation and derigging of the device. - Page 36 ©2021 Showtec...