Specifications - Vitek VT-1904 Instruction Manual

ENGLISH
•
Pass the power cord between the halves of the
floor support (1) (pic. 3).
•
Match the ledges on one half of the support (1)
with the openings on the other half of the sup-
port (1) and connect the support (1) halves till the
latches actuate (pic. 3).
•
Place the assembled support (1) on the lower part
of the fan body (2), make sure that the ledges on
the fan body (2) match the openings on the sup-
port (1) and after that tighten the fastening nut
clockwise (Fig. 4).
•
Fix the power cord in the channel of the support
(1) (pic. 4).
USAGE
•
Turn the power switch (7) «ON/OFF» to the posi-
tion «ON» and press any speed selection button
«1-2-3», the fan will start operating.
•
Select the air flow speed by pressing the buttons
(8) «0-1-2-3» on the control panel (5).
«0» – The fan is switched off (reset button).
"1" – Low air flow speed.
"2" – Medium speed of air flow,
"3" – High air flow speed.
•
Switch the oscillation mode on by pressing the
button (9) on the control panel (5); to switch the
oscillation mode off, press the button (9) again.
•
Select the operation time of the automatic switch-
off timer with the timer control knob (7) on the
control panel. You can set the continuous oper-
ation time up to 60 minutes. To switch the timer
off, turn the control knob (7) again to the posi-
tion «OFF».
MAINTENANCE AND CARE
•
Before cleaning the fan switch it off and remove
the plug of the power cord from the socket.
•
Wipe the fan body (2) with a soft, slightly damp
cloth and then wipe it dry.
•
Do not use solvents or abrasives for cleaning of
the unit body.
•
Do not immerse the fan body (2), the power cord
and the plug into water or any other liquids; pro-
vide that water does not get into the fan body to
avoid electric shock or damaging the unit.
•
To clean the air inlets of the grid (6) on the rear
side of the fan you can use a vacuum cleaner with
a corresponding attachment.
•
Make sure that the power cord does not touch
sharp objects or furniture edges.
•
Before taking the fan for long storage clean it, dis-
assemble the floor support (1), pack the fan into
its package and put it to a dry cool place away
from children.
•
Before switching the fan on next time assemble
it, check its workability and integrity of the power
cord isolation.
STORAGE
•
Unplug the fan and clean it.
•
Pack the fan into the original package and put it
away for storage in a dry cool place away from
children.
•
Keep the unit in a cool dry place unreachable by
children or handicapped persons.
DELIVERY SET
Fan body – 1 pc.
Floor support – 1 pc. (consists of two pieces)
Manual – 1 pc.
Warranty Certificate – 1 pc.

SPECIFICATIONS

Power supply: 220-240 V ~ 50 Hz
Rated input power: 45 W
RECYCLING
For environment protection do not throw out the unit
and the batteries (if included), do not discard the unit
and the batteries with usual household waste after the
service life expiration; apply to specialized centers for
further recycling.
The waste generated during the disposal of the unit is
subject to mandatory collection and consequent dis-
posal in the prescribed manner.
For further information about recycling of this prod-
uct apply to a local municipal administration, a dis-
posal service or to the shop where you purchased
this product.
The manufacturer preserves the right to change
design, structure and specifications not affecting
general principles of the unit operation without a pre-
liminary notification due to which insignificant dif-
ferences between the manual and product may be
observed. If the user reveals such differences, please
report them via e-mail info@ vitek.ru for receipt of an
updated manual.
Unit operating life is 3 years
Guarantee
Details regarding guarantee conditions can be
obtained from the dealer from whom the appliance
was purchased. The bill of sale or receipt must be
produced when making any claim under the terms of
this guarantee.
This product conforms to the EMC
Directive 2014/30/EU and to the Low
Voltage Directive 2014/35/EU.
4