Summary of Contents for Bass Habit Elite SE550.2DF
Page 1
SE550.2DF SE225.4DF SE550.4DF SE2200.5DF Elite Class D Full Bridge Multi Channel Amplifier User Manual...
Page 3
THANK YOU! Thank you for purchasing this SPL Elite Class D full bridge amplifier from Bass Habit. Please read this manual in order to fully understand how to get the best result from this product and ensure that the advices on how to look after the product and the safety precautions are followed.
TABLE OF CONTENT • SAFETY & WARRANTY Caution Warranty What is not covered Warning International technical enquiries • INSTRUCTIONS Installation experience Choosing amplifier mounting locations Installation precautions Step 1) Power connections Step 2) Speaker connections Step 3) Signal connections • CONTROL PANEL Front panel Input level control (GAIN) Bass boost control (BASS BOOST)
Ensure that no moving parts get caught on the subwoofer or grill. WARRANTY All Bass Habit products carry a full warranty depending on the conditions in the country where it is sold. The warranty is valid from the date of the original receipt as proof of purchase (warranty period differs depending on local warranty laws and policies).
• When making connections, make certain all cables are secure and properly insulated. STEP 1) POWER CONNECTIONS The Bass Habit SPL Elite amplifiers are capable of delivering extremely high power levels and require a heavy-duty and reliable connection to the vehicle’s electrical system. To get the very best performance out...
Page 7
REMOTE CONNECTION (REM): Connect the amplifiers Remote (REM) terminal to the source unit Remote turn on lead using a minimum of 0.75mm2/18 gauge wire. If your source unit does not have a turn on connection, connect the amplifier (REM) terminal through a power switch button which can provide a +12V signal. Remote wire maximum accepted size for terminal: SE550.2DF: MAX 10 awg / 6mm2...
STEP 2) SPEAKER CONNECTIONS SPEAKER CONNECTIONS (SPEAKER OUTPUT): Speaker connections should be made using a minimum of 16 awg/1,25mm2 wire. The terminal accepts up to 8 awg/10mm2. Minimum total allowed impedance load is 1 – 2 ohm depending on model. WARNING! DO NOT START the amplifier WITHOUT a load on the speaker output terminals.
STEP 3) SIGNAL CONNECTIONS SIGNAL CABLE CONNECTION (SIGNAL INPUT): Use high quality RCA signal cables to make sure you get the full audio experience. FIG 7: SIGNAL CABLE CONNECTION TWO CHANNEL AMPLIFIER FIG 8: SIGNAL CABLE CONNECTION FOUR CHANNEL AMPLIFIER...
Page 12
STEP 3) SIGNAL CONNECTIONS SIGNAL CABLE CONNECTION (SIGNAL INPUT): Use high quality RCA signal cables to make sure you get the full audio experience. FIG 9: SIGNAL CABLE CONNECTION FIVE CHANNEL AMPLIFIER...
FRONT PANEL (SEE FIG 4 ON THE NEXT PAGE) Bass Habit SPL Elite amplifiers are can be used for speakers and subwoofers in the range between 15Hz - 20KHz. On the four channel and five channel amplifiers there is a crossover switch for LOW/FLAT/HIGH mode as well.
Page 14
FIG 4: FRONT PANEL RCA signal input Connect the RCA signal wire from the audio source / head unit High pass filter (HPF) Adjust High pass filter crossover point (15Hz - 3/6KHz) Low pass filter (LPF) Adjust Low pass filter crossover point (50Hz - 6/20KHz) Gain Adjust the Gain level (0,2-5V) Bass boost level (LEVEL)
TROUBLESHOOTING TROUBLESHOOTING: Symptom Check / Control No sound • Check and measure voltage at +12V and REM terminals / No active PWR LED (allowed working range is 10.5-15.5V DC). • Check and measure ground connections. • Check external fuse. • Check input signal and cables from source unit. •...
Page 18
The crossed-out wheelie bin symbol means that the product, literature and packaging included must be taken to separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste: dispose of them at a recycling point. For info on your nearest recycling point, check with your local waste authority.