Related Manuals for Renesas QB-78K0FX2L
Summary of Contents for Renesas QB-78K0FX2L
- Page 1 QB-78K0FX2L In-Circuit Emulator User’s Manual Target Devices: 78K0/FY2-L 78K0/FA2-L 78K0/FB2-L Rev.1.00 2012.5...
- Page 3 General Precautions for Handling This Product 1. Circumstances not covered by product guarantee • If the product was disassembled, altered, or repaired by the customer • If it was dropped, broken, or given another strong shock • Use at overvoltage, use outside guaranteed temperature range, storing outside guaranteed temperature range •...
- Page 4 PDF file and specifying it in the “Find what:” field. To know the manipulations, command functions, and other software-related settings of the QB-78K0FX2L → See the user’s manual of the debugger (supplied with the QB-78K0FX2L) to be used. Conventions Note:...
- Page 5 The related documents listed above are subject to change without notice. Be sure to use the latest version of each document for designing, etc. IECUBE is a registered trademark of Renesas Electronics Corporation in Japan and Germany. Windows is either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
-
Page 6: Table Of Contents
2.3.7 Precautions for handling NQ (using 16pin or 20pin) ..............26 2.3.8 Precautions for mounting IC using NQ and MA (using 30pin) ..........27 2.4 Connecting QB-78K0FX2L to Target System..................28 2.5 Notes on Power Supply and GND Pin Connection................30 2.6 Connecting USB Interface Cable and AC Adapter ................30 2.7 Switching Power On and Off.......................30... -
Page 7: Chapter 1 General
CHAPTER 1 GENERAL CHAPTER 1 GENERAL The QB-78K0FX2L is an in-circuit emulator for emulating the 78K0/Fx2-L. Hardware and software can be debugged efficiently in the development of systems in which the 78K0/Fx2-L is used. This manual descries basic setup procedures, hardware specifications, system specifications, and how to set switches. -
Page 8: Hardware Specifications
QB-78K0FX2L In-Circuit Emulator CHAPTER 1 GENERAL 1.1 Hardware Specifications Table 1-1. QB-78K0FX2L Hardware Specifications Parameter Specification 78K0/FY2-L, 78K0/FA2-L, 78K0/FB2-L Target device Operating voltage 1.8 to 5.5V 2.7 V V 5.5 V :1 to 10 MHz Note1 Note2 Operating... - Page 9 QB-78K0FX2L In-Circuit Emulator CHAPTER 1 GENERAL Note1 112mm Note2 108mm 58mm Note3 adapter Rear space Note4 adapter Front space Notes 1. Does not include projection of power switch 2. Includes projection of screw that fixes rear space adapter 3. Rear space adapter can adjust the height from 30 mm (longest) to 0 mm (shortest) 4.
-
Page 10: Names And Functions Of Hardware
1.2 Names and Functions of Hardware Top View Power switch Bottom View OSC1 TCN2 TCN1 TARGET POWER (Green LED) (Red LED) Side View Power supply connector USB connector Figure 1-1. Names of Parts of QB-78K0FX2L R20UT2057EJ0100 Rev.1.00 Page 10 of 37 2012.05.18... - Page 11 This is a connector for the shipment inspection. It is not something that the user will need. (4) POWER (Red LED) This is an LED that shows whether the power supply of the QB-78K0FX2L is switched on. Table 1-2 POWER(Red LED) LED...
-
Page 12: System Specifications
QB-78K0FX2L In-Circuit Emulator CHAPTER 1 GENERAL 1.3 System Specifications This section shows the QB-78K0FX2L system specifications. Table 1-4. QB-78K0FX2L System Specifications Parameter Specification Emulation memory capacity Internal ROM 512 KB (MAX.) Internal RAM 61KB (MAX.) Program execution Real-time execution function... -
Page 13: System Configuration
QB-78K0FX2L In-Circuit Emulator CHAPTER 1 GENERAL 1.4 System Configuration This section shows the system configuration when using the QB-78K0FX2L connected to a PC (Windows PC/AT compatible). Connection is possible even without optional products. Figure 1-2. System Configuration <1> <3> <5>... - Page 14 QB-78K0FX2L In-Circuit Emulator CHAPTER 1 GENERAL Remarks 1. Refer to 1.6 Package Contents for the purchase forms of the above products. 2. As for handling of connectors, refer to 2.3 Mounting and Connecting Connectors. 3. The part number of <4> differs depending on the region of use. See Table 1-7 Part Numbers of AC Adapter for IECUBE Classified by Region for the part numbers.
-
Page 15: System Configuration For Each Target Device
CHAPTER 1 GENERAL 1.5 System Configuration for Each Target Device The following table lists the system configuration for each target device of the QB-78K0FX2L. The adapter and connector for each device, and common probe and adapter are sold separately. An exchange adapter, a YQ connector, a target connector, and an emulation probe are included, depending on the order product name. -
Page 16: Package Contents
QB-78K0FX2L In-Circuit Emulator CHAPTER 1 GENERAL 1.6 Package Contents The included products are described for each order product name. Products supplied with QB-78K0FX2L-ZZZ QB-78K0FX2L USB interface cable (2 meters) Probe holder Online user registration card (warranty card and software contract in one) -
Page 17: Ac Adapter For Iecube
QB-COMMON-PW-TW Notes 1. Products are shipped only on order from each region. 2. Contact a distributor or a Renesas Electronics sales representative for information on regions other than the above. 3. Only the AC adapter usable in each region can be ordered R20UT2057EJ0100 Rev.1.00... -
Page 18: Chapter 2 Setup Procedure
CHAPTER 2 SETUP PROCEDURE CHAPTER 2 SETUP PROCEDURE This chapter explains the QB-78K0FX2L setup procedure. Setup can be completed by performing installation setup in the order in which it appears in this chapter. Perform setup along the lines of the following procedure. -
Page 19: Software Settings
QB-78K0FX2L In-Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2.1 Software Settings Check the user's manual for the debugger that will be used. 2.2 Clock Settings The IECUBE clock must be set to the clock used by the target device. For details about how to set the clock, check the user's manual for the debugger that will be used. - Page 20 The clock generated from the oscillator mounted on the emulator is used. The selectable frequencies are same as those of the target device. To modify the clock setting, the acrylic board on the bottom of the QB-78K0FX2L must be removed. The acrylic board can be removed by lifting it up.
- Page 21 QB-78K0FX2L In-Circuit Emulator CHAPTER 2 SETUP PROCEDURE Figure 2-1. Acrylic Board Removal Method Note As an oscillator to be mounted in the OSC1 socket in the emulator, use the one that satisfies the following specifications. - Supply voltage: 5 .0V - Output level: CMOS Note An oscillator that uses a resonator cannot be used.
- Page 22 QB-78K0FX2L In-Circuit Emulator CHAPTER 2 SETUP PROCEDURE Figure 2-3. Mapping of Oscillator to Socket Remark Insert the oscillator into the socket, take care for the pin 1 position. (2) Internal high-speed oscillation clock This method uses the clock inside the emulator by configuring the use of the high-speed oscillation clock in the user program.
-
Page 23: Mounting And Connecting Connectors
CHAPTER 2 SETUP PROCEDURE 2.3 Mounting and Connecting Connectors This section describes the methods of connecting the QB-78K0FX2L and target system. Make connections with both the QB-78K0FX2L and target system powered OFF. The following abbreviations are used in this section:... -
Page 24: Mounting Nq To Target System (Using 16Pin Or 20Pin)
QB-78K0FX2L In-Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2.3.2 Mounting NQ to target system (using 16pin or 20pin) (1) Thinly apply an adhesive to the back of the NQ and adhere the NQ to the target system. In addition, be sure to clean the back of the NQ as well as the surface of the target system using alcohol or the like. -
Page 25: Mounting Yq To Nq (Using 30Pin)
QB-78K0FX2L In-Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2.3.3 Mounting YQ to NQ (using 30pin) (1) After confirming that there are no broken or bent YQ contact pins, fit the YQ in the NQ and fasten it using the supplied YQGUIDE (for the fastening method, see the next step, (2)). If repeatedly inserting and removing, be sure to inspect the YQ pins before fitting. -
Page 26: Precautions For Handling Nq, Yq, Sa, And Ca (Using 30Pin)
QB-78K0FX2L In-Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2.3.6 Precautions for handling NQ, YQ, SA, and CA (using 30pin) (1) When taking the NQ from the box, press down on the body and take out the sponge first. (2) Since the pins of the YQ are thin and easily bent, be careful. When inserting it in the NQ, confirm that there are no bent pins. -
Page 27: Precautions For Mounting Ic Using Nq And Ma (Using 30Pin)
QB-78K0FX2L In-Circuit Emulator CHAPTER 2 SETUP PROCEDURE 2.3.8 Precautions for mounting IC using NQ and MA (using 30pin) (1) Confirm that there is no weld flash in the resin (sealant part) of the IC. If there is weld flash, remove it using a knife or the like. -
Page 28: Connecting Qb-78K0Fx2L To Target System
There are three GND wires in the emulation probe. Connect them to the QB-78K0FX2L and target system. <1> Fasten the GND wire on the QB-78K0FX2L side of the emulation probe to the nut on the bottom of the QB-78K0FX2L using a #0 or #1 Phillips precision screwdriver (connection of B to A in Figure 2-6). - Page 29 <2> Be sure to connect the GND wire of the emulation probe to the QB-78K0FX2L and the target system. If it cannot be connected, the impedance of the cable is unstable and could bring about lowering of signal transmission characteristics or distortion of the output waveform for an input waveform.
-
Page 30: Notes On Power Supply And Gnd Pin Connection
2.6 Connecting USB Interface Cable and AC Adapter Plug the USB interface cable supplied with the QB-78K0FX2L into the USB connector of the host machine, and plug the other side into the USB connector on the rear of the QB-78K0FX2L. -
Page 31: Chapter 3 Settings At Product Shipment
QB-78K0FX2L In-Circuit Emulator CHAPTER 3 SETTINGS AT PRODUCT SHIPMENT CHAPTER 3 SETTINGS AT PRODUCT SHIPMENT Table 3-1. Settings at Shipment Item Setting Remarks Note Not mounted Oscillator can be mounted OSC1 Power switch Set to OFF at shipment. Note The oscillation circuit using an oscillation cannot be used. -
Page 32: Chapter 4 Cautions
QB-78K0FX2L is connected. - Pin characteristics The pin characteristics of the QB-78K0FX2L slightly differ when the target device is mounted to the target system, because a connector, adapter, emulation probe, and circuit board exist between the QB-78K0FX2L and the target system. - Page 33 QB-78K0FX2L In-Circuit Emulator CHAPTER 4 CAUTIONS -The device and IECUBE have different circuit equivalences. - The VDD pin of IECUBE is provided with a power supply detection circuit and is internally connected to a 2 k pull-down resistor. - The RESET pin of IECUBE is connected to a 2 M pull-down resistor.
-
Page 34: Debugging Note
After power application, a program will be executed for the target device mounted in the target system when reset is released. However, with the QB-78K0FX2L, the program does not start until an operation to start execution is performed after the program is downloaded using the debugger. - Page 35 QB-78K0FX2L In-Circuit Emulator User’s Manual May 18th, 2012 Rev.1.00 Publication Date: Published by: Renesas Electronics Corporation...
- Page 36 SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. Renesas Electronics America Inc. 2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A. Tel: +1-408-588-6000, Fax: +1-408-588-6130 Renesas Electronics Canada Limited 1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada...
- Page 37 QB-78K0FX2L In-Circuit Emulator User’s Manual R20UT2057EJ0100...