Table of Contents
Related Manuals for CD Automation CD-KP CD3000E
Summary of Contents for CD Automation CD-KP CD3000E
- Page 1 USER MANUAL CD-KP Rev. 02/2005 for MULTIDRIVE & CD3000E CD Automation S.r.l. Via Picasso 34/36 - 20025 – Legnano (MI) – Italy Tel +39 0331 577479 – Fax +39 0331 579479 e-mail: info@cdautomation.com - web: www.cdautomation.com...
- Page 3 CD-KP for MULTIDRIVE and CD3000E Index 1 CD-KP for MULTIDRIVE and CD3000E 1.1 General description 1.2 Ordering code 1.3 Dimensions 1.4 Wiring connection 1.5 Retransmission selection 1.6 Frontal Keypad 1.7 Frontal plug-in connector 1.8 Default settings 1.9 Start-up 2 Menu general description 2.1 General description of menus 2.2 Password usage oper...
-
Page 4: General Description
C.D. Automation Srl CD-KP for CD3000E & Multidrive User’s Manual 1 CD-KP for MULTIDRIVE and CD3000E 1.1 General description CD-KP is a panel device allowing to display some operative parameters of thyristor units as voltage, current, power, reference, alarms, etc. CD-KP can be configured to select which parameter to display and is possible to execute commands as start and stop of the connected unit, display and reset of alarms, to change reference and ramp. - Page 5 User’s Manual CD-KP for CD3000E & Multidrive C.D. Automation Srl 1.3 Dimensions www.cdautomation.com...
-
Page 6: Wiring Connection
C.D. Automation Srl CD-KP for CD3000E & Multidrive User’s Manual 1.4 Wiring connection All the wirings are done via the rear terminals, following the schema. The supply of CD-KP can be 120Vac or 240Vac and must be specified in ordering code. 0÷20mA 120Vac 4 20mA... - Page 7 User’s Manual CD-KP for CD3000E & Multidrive C.D. Automation Srl 1.6 Frontal Keypad In the figure below are showed the displays, the keys and the frontal plug-in of CD-KP. Upper display: Lower Display: Used to display the menu items, the 1.6.1 Used to display the parameters’...
-
Page 8: Default Settings
C.D. Automation Srl CD-KP for CD3000E & Multidrive User’s Manual 1.8 Default settings CD-KP is supplied with a base configuration allowing the immediate usage without any further configuration. Some default values are reported in the following table. Function Value Notes Addressed unit Baud Rate 19200... - Page 9 User’s Manual CD-KP for CD3000E & Multidrive C.D. Automation Srl 2 Menu general description 2.1 General description of menus The main menu of CD-KP is composed by 6 sections: oPEr Setu Conf OPERATOR COMMAND CALIBRATION DIAGNOSTIC SETUP CONFIGURATION Each section is composed by one or more items or sub-menus. oper At any time, it’s possible to return to the item in main menu by pressing together the...
- Page 10 C.D. Automation Srl CD-KP for CD3000E & Multidrive User’s Manual www.cdautomation.com...
- Page 11 User’s Manual CD-KP for CD3000E & Multidrive C.D. Automation Srl www.cdautomation.com...
- Page 12 C.D. Automation Srl CD-KP for CD3000E & Multidrive User’s Manual oper 2.3 Operator menu ( The operator menu can’t be protected by password. It is composed by 5 sub-menus. The scrolling through the sub-menus is done by pressing the roll key To return to main menu, press together the roll and up keys.
- Page 13 User’s Manual CD-KP for CD3000E & Multidrive C.D. Automation Srl ALAr 2.3.5 Alarm sub-menu ( In there is no alarm, in the lower display will appear , otherwise CD-KP will display the alarm type: noPh. • Loss of one or more phases. Ph.er •...
-
Page 14: Calibration Menu
C.D. Automation Srl CD-KP for CD3000E & Multidrive User’s Manual 2.4 Command menu ( In this menu is possible to send two commands to the thyristor unit connected to CD-KP: re.st reset command to delete alarms and restore the unit to re-start ( will flash in lower display) Star... -
Page 15: Diagnostic Menu
User’s Manual CD-KP for CD3000E & Multidrive C.D. Automation Srl 2.6 Diagnostic menu ( This menu is useful during installation or in case of malfunction. The scrolling through the parameters is done by pressing the roll key To return to main menu, press together the roll and up keys. - Page 16 C.D. Automation Srl CD-KP for CD3000E & Multidrive User’s Manual P 49 2.6.5 Parameter 49 – Digital outputs ( This parameter displays two digits indicating the output’s status as below specificated: no output active no output active configurable output 2 active line activation signal alarm signal configurable output 1 active...
-
Page 17: Setup Menu
User’s Manual CD-KP for CD3000E & Multidrive C.D. Automation Srl SEtU 2.7 Setup menu ( This menu is similar to diagnostic menu. The scrolling through the parameters is done by pressing the roll key . To modify parameters’ values press up or down keys. - Page 18 C.D. Automation Srl CD-KP for CD3000E & Multidrive User’s Manual P 98 2.7.11 Parameter 98 – Load type connection ( Star without neutral Star with neutral Delta Open delta P104 2.7.12 Parameter 104 – Analog output 1 rescaling ( Span for external indicator 1 –...
-
Page 19: Configuration Menu ( Conf )
User’s Manual CD-KP for CD3000E & Multidrive C.D. Automation Srl Conf 2.8 Configuration menu ( In this menu is possible to configure CD-KP. The scrolling through the parameters is done by pressing the roll key . To modify parameters’ values press up or down keys. - Page 20 C.D. Automation Srl CD-KP for CD3000E & Multidrive User’s Manual op1u 2.8.7 OP1 upper display ( Displayed parameter in upper display of OP1 menu. arst Possible values: More informations about thyristor unit’s parameters can be found on CD3000E and Multidrive manuals.
- Page 21 User’s Manual CD-KP for CD3000E & Multidrive C.D. Automation Srl P.CAL 2.8.13 Calibration menu password ( Protection password for calibration menu. Possible values: – If this value is set to then there is not password protection and the access to calibration menu is free for all operators.