Advertisement
Quick Links
New Penton - 2 Door Wardrobe
Assembly Instructions
Dimensions
Width - 85cm
Depth - 51cm
Height - 180cm
Important –
Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the
- Please keep for future reference
Customer Helpline: 08456 400 800
257/8853
275/0705
266/9690
Issue 1 - 14/05/14
Advertisement
Related Manuals for Argos New Penton
Summary of Contents for Argos New Penton
- Page 1 New Penton - 2 Door Wardrobe Assembly Instructions - Please keep for future reference 257/8853 275/0705 266/9690 Dimensions Width - 85cm Depth - 51cm Height - 180cm Important – Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the...
- Page 2 Safety and Care Advice Important – Please read these instructions fully before starting assembly Check you have all the This product has been produced We do not components and tools listed on from natural timber; you may recommend the pages 2 and 3. notice some variation in the grain use of power and colour of different component...
- Page 3 Components - Panels Please check you have all the panels listed below underside 1 Right side panel (178 x 49cm) 8 Top panel (85 x 50.4cm) underside 2 Left side panel 9 Base panel x 2 (79.4 x 47.4cm) (178 x 49cm) 10 Front frame x 2 (68.6 x 6.5cm) 11 Smaller H profile...
- Page 4 Components - Fittings If you have damaged or missing components, call the Customer Helpline: 08456 400 800 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
- Page 5 Assembly Instructions Step 1 Fixing right front frame. (Two people required for an easier assembly). Insert right side panel into right front frame through joints. Yes! Note: Before fixing the blocks into place it is important to ensure that the slot and groove of parts are fully pushed together Attention: correct...
- Page 6 Assembly Instructions Step 3 Fitting Metal dowels. Screw metal dowels into right side panel Note: Insert metal dowels as far as shown. Do not over tighten. Repeat step 3 for the left side panel Step 4 Insert dowels into the indicated parts.
- Page 7 Assembly Instructions Step 5 Inserting front frame. Insert the front frames into holes on right side panel , as shown. Step 6 Attention: Fixing base panel. With help, fit base panels to right side panel Attention! Round edge on base panels must be facing front.
- Page 8 Assembly Instructions Step 7 Fixing left side panel. With help, place left side properly panel ensuring dowels and front frames are all fit into their holes at the same time. Insert 6 locking nuts into base panels where shown. Use a screwdriver to turn locking nuts clockwise to lock.
- Page 9 Assembly Instructions Step 9 Fixing top panel. With help, fit top panel to the cabinet then fix it using screws Make sure round edge is facing up. Important: After fixing the top panel, with help, carefully stand the product upright. Step 10 Insert hanging rail into...
- Page 10 Assembly Instructions Step 11 Fitting hinges to doors. Attach hinges in the pre marked holes on door using screws shown. Fix cross rails in the pre drilled holes on door using screws Repeat step 11 for the other door. Step 12 Hanging doors.
- Page 11 Assembly Instructions Step 13 Hinge adjustment. View from behind To move doors up or down: loosen screws shown and move doors to suit. Once doors are aligned, re-tighten screws. To move doors left or right: loosen screws shown and move doors to suit.
- Page 12 Assembly Instructions Step 15 Fitting door locks. Screw clips in place using screws Ensure that the 2 small wheels are flush with the edge of the base as shown in the diagram. Insert plugs into clips , ensuring they are leveled as shown in the diagram.
- Page 13 Assembly Instructions Step 16 Fixing back panels. Important: Cabinet MUST ‘square’ when back panels are attached. Make sure back panels are in flush with the edge of the top panel prior to fixing. Attach the right back panel first using nails Position profiles onto back panel (just attach).
-
Page 14: A Guide To - Wall Mounting & Fixings
A Guide to - Wall Mounting & Fixings Important: When drilling into walls always Important note: check that there are no hidden wires or pipes etc. If plastic wall plugs Make sure that the screws and wall plugs being used are supplied with your are suitable for supporting your unit.
Need help?
Do you have a question about the New Penton and is the answer not in the manual?
Questions and answers