Pentair HYDROMATIC SH Installation And Service Manual
Pentair HYDROMATIC SH Installation And Service Manual

Pentair HYDROMATIC SH Installation And Service Manual

Submersible solids handling pump

Advertisement

Quick Links

MODEL SH
SUBMERSIBLE
SOLIDS HANDLING PUMP
INSTALLATION AND SERVICE MANUAL
For use with product built with Marathon
motor.
®
NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible
party who maintains the system.
Item # E-03-305 | Part # 5625-305-1 | © 2012 Pentair Pump Group, Inc. | 10/25/12

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HYDROMATIC SH and is the answer not in the manual?

Questions and answers

Summary of Contents for Pentair HYDROMATIC SH

  • Page 1 NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible party who maintains the system. Item # E-03-305 | Part # 5625-305-1 | © 2012 Pentair Pump Group, Inc. | 10/25/12...
  • Page 2: General Information

    CALIFORNIA PROPOSITION green wire for ground. Be sure General 65 WARNING: green wire is connected to a good ground such as water pipe or Information This product and ground stake. related accessories contain chemicals known to the State of Thank you for purchasing your California to cause cancer, birth Heat Sensors: Hydromatic...
  • Page 3 Two pumps operate together only Alarm Controls: IMPORTANT: If Hydromatic if sump level rises to the third electrical controls are not used The alarm level is usually set and the motor fails be cause of or over ride control. The override above the override level so control also brings on the second improper components or if the...
  • Page 4: Pump Installation

    valve should be in stalled on the one set can be used in the sump General discharge side of the check valve when making con nec tions. The so if nec es sary to service the size wire to use from pan el to Information check valve, the line pressure can sump de pends on motor size and...
  • Page 5: Pump Operation

    24 inches above the lower 6. Turn both H-O-A switch es Pump turn-off con trol. to Auto position and allow sump to fill to the over ride Operation More distance between turn-on control level. and turn-off controls can be used, but sew age may be come septic 7.
  • Page 6 Replacing Stator: This is im por tant as leads Pump must be tucked behind the 1. If stator only is dam aged windings by using hands up Maintenance it may not be necessary to through rotor core. completely dismantle pump as stator and hous ing can be If seal failure is not used, the lifted from pump without...
  • Page 7: Pump Troubleshooting

    Hydromatic submersible oil 6. Remove lower seal spring and Pump in this chamber. Replace plug; pry out seal with screwdriver. use Permatex on threads. Troubleshooting 7. To remove seal hous ing, take Install air valve in top plug out socket head bolts and opening of motor housing and using bolts in back of holes, charge housing with about...
  • Page 8 Pump runs but will not shut off: Motor stops and then re starts after short period but overload 1. Pump may be air locked. heaters in starter do not trip: Turn pump off and let set for several minutes, then restart. 1.
  • Page 9: Parts List

    Parts List ® For use with product built with Marathon motor. Ref. Part Part Ref. Part Part Ref. Part Part Description Qty. Description Qty. Description Qty. 21929A002 Eyebolt 00178-001-1 Bolt 24407C217 Stator 2 HP 230/460/3/60 1750 RPM 152740355 35' Cord Cap Assembly 14-4 00295-001-2 Seal Plate 24407C218...
  • Page 10 20 21 22 23 24 25 26...
  • Page 12: Standard Limited Warranty

    Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility.

Table of Contents