P2 Ch9-16: Select The Inputs For Mixer Channels 9-16; P3 Ineq1-4: Eq Settings For Inputs 1-4 - Korg D16 Owner's Manual

These inputs are sent via the stereo/mono switch
through the balance and fader settings, and then to
the master LR bus.
Use the [AUX OUT] jack to transmit the effect send
to your external effect processor. ( p.82 [MASTER
EFFECT/AUX] "AuxSend" tab page)
3a. Stereo/Mono ...................... [Stereo, Mono]
Stereo: Odd-numbered channel inputs will be
sent to the master L bus, and even-numbered chan-
nel inputs will be sent to the master R bus.
Mono: Odd-numbered and even-numbered
channel inputs will be summed, and the same sig-
nal will be sent to the master L bus and R bus.
Use this when the input is received on only one
channel.
If the sound distorts when this is set to "Mono,"
adjust the level on the input device or using the
[TRIM] knob.
3b. Balance ..........................[L63...CNT...R63]
Adjust the balance for when the sub input is sent in
stereo to the master LR bus.
3c. Fader .......................................[000...100]
Adjust the amount of sub input signal that is sent to
the master LR bus.
3d. Mute............................................[On, Off]
On: The sub input will be muted; it will not be
sent to the master LR bus.
Off: The sub input will not be muted; it will be
sent to the master LR bus.
4. Pair ................................................................
This lets you pair adjacent mixer channels.
Press the " " button to access the following screen.
4a
4b
Channels that are paired will be controlled by the
knobs and fader of the odd-numbered channel.
Operating the knobs or fader of the even-numbered
channel will not control anything.
4a. Select ChannelPair .....................[1 2...7 8]
Press the "1 2"–"7 8" button for the channels that
you wish to pair. When pairing is "On," the heart
icon will be displayed.
4b. Select Function ........... [Eq, Send, Aux, Pan]
Select the functions that will be paired for the chan-
nels selected by "Select ChannelPair."
For the functions "EQ"–"Pan" that you wish to
pair, press the button to enable pairing (the button
will be highlighted). The settings will be applied
when you press the "OK" button.
When pairing is on, the pairing function will
always apply to the fader and track status.
76
P2 Ch9–16: Select the inputs for
mixer channels 9–16
Here you can select the inputs for mixer channels 9–16.
Refer to "P1 Ch1–8: Select the inputs for mixer channels
1–8."
P3 InEq1–4: EQ settings for inputs
1–4
Here you can apply EQ (equalizer) to the analog inputs
from the [INPUT 1/GUITAR IN]–[INPUT 4] jacks.
Make these settings when you wish to directly record
the sound that is adjusted by the EQ.
The EQ has three bands. High EQ and low EQ are
shelving type, and the mid EQ is a peaking type with
adjustable cutoff frequency.
This EQ cannot be used on the digital input (S/P
DIF IN) or on the rhythm.
5
1
3 4
1. InputLevelMeter...............................................
(1, 2, 3, 4/0, –6, –12, –18, –40dB)
This shows the level of each analog input. The hori-
zontal axis indicates the channel, and the vertical
axis indicates the level.
Inputs that are not selected in "Ch1...8" ([INPUT]
P1-1) will not be displayed.
2. InputHigh.......... [(Fc=10kHz)–15.0...+15.0(dB)]
Set the input high EQ gain. This adjusts the high-
frequency range.
You can cut/boost over a range of –15 – +15 dB at a
10 kHz cutoff frequency.
3. InMidFc............................. [100Hz...20.0k(Hz)]
Set the cutoff frequency for the input mid EQ.
This can be adjusted over the range of 100 Hz–20
kHz.
4. InputMid ............................ [–15.0...+15.0(dB)]
Set the input mid EQ gain. This adjusts the mid-fre-
quency range.
You can cut/boost over a range of –15 – +15 dB at
the cutoff frequency specified by "InMidFc."
5. InputLow........... [(Fc=100Hz)–15.0...+15.0(dB)]
Set the input low EQ gain. This adjusts the low-fre-
quency range.
You can cut/boost over a range of –15 – +15 dB at a
100 Hz cutoff frequency.
6. Pair ................................................................
Enable pairing for adjacent mixer channels. ( p.76
"Pair")
2
6