Input/Output/Solo; Ch1-6: Select Inputs For Mixer Channels 1-6; Ch7-12: Select Inputs For Mixer Channels 7-12 - Korg D1200 Owner's Manual

INPUT/OUTPUT/SOLO

Ch1–6: Select inputs for mixer chan-
nels 1–6
Here you can select the inputs for mixer channels 1–6. For
details on connecting each input jack, refer to p.14.
1
1. Ch1...6 .............................................................
[Input1....4, S/PDIF L, R, RhythmL, R, CD L, R*]
Select a "Ch1"–"Ch6" channel icon, and select the
source that will be input to each channel.
INPUT1...4: Input the analog audio signal from an
instrument etc. connected to the [INPUT 1/GUITAR
IN]–[INPUT 4] jacks.
S/P DIF L, R: Input the digital audio signal from a CD or
DAT etc. connected to the [S/P DIF IN] jack. This can be
selected if "DigiIn" is "On."
Insert effects cannot be used when using digital in-
put.
RhythmL, R: Input the rhythm selected by
"SelRhythm" ( p.96). The rhythm will sound during
recording and playback, regardless of the "Rhythm" set-
ting ( p.96). This rhythm can be recorded ( p.48).
CD L, R: Input the audio signal from an audio CD
inserted in the CDRW-1.
*CD L, R can be selected only if the CDRW-1 is installed.
2. DigiIn ..................................................[On, Off]
Turn this "On" when you want to use digital input (S/P
DIF IN).
On: You will be able to select "S/P DIF L" or "S/
P DIF R" for "Ch1...6."
Insert effects cannot be used if this is "On."
Off: You will not be able to select "S/P DIF L" or
"S/P DIF R" for "Ch1...6."
Turn this "On" if you want to use digital input (S/P DIF
IN). When you press the "DigiIn" button, a message of
"Obey Copyright Rules" will appear. Carefully read the
section "COPYRIGHT WARNING" ( p.1), and if you
accept the terms, press the [YES/OK] key in response to
"Are You Sure?" Digital input will be enabled.
98
3. SubIn................................................................
3a
3b
3c
3d
These settings let you use the [INPUT 1/GUITAR IN]–
[INPUT 4] jacks as "sub inputs," for example when you
want to use these jacks as the returns from an external
4
effect device, or when you want the sound of instru-
ments connected to these jacks to be combined with the
2
track playback. ( p.67)
3
Sub input can be used when you want to synchronize an
external sequencer with a completed song on the D1200,
and mix the instrumental sounds played by the
sequencer with the playback tracks of the D1200.
These inputs will be sent through the stereo/mono
switch, balance, and fader to the master LR bus.
Use the [AUX OUT] jack to output the send signal to the
external effect device. ( p.90: [MASTER EFFECT/
AUX] "AuxSend" tab page)
3a. Stereo/Mono ........................ [Stereo, Mono]
Stereo: The odd-numbered channel input will be
sent to the master L bus, and the even-numbered chan-
nel input will be sent to the master R bus.
Mono: The odd-numbered and even-numbered
inputs will be combined, and the same signal will be
sent to the master L and R buses. Use this setting if the
input signal consists of only one channel.
If the sound is distorted when you use the "Mono"
setting, adjust the level on the output device or us-
ing the [TRIM] knob.
3b. Balance .............................[L63...CNT...R63]
Specifies the balance at which the sub input will be sent
to the master LR bus in stereo.
3c. Fader ......................................... [000...100]
Specifies the level at which the sub input will be sent to
the master LR bus.
3d. Mute..............................................[On, Off]
On: The sub input will be muted; it will not be sent
to the master LR bus.
Off: The sub input will not be muted; it will be sent
to the master LR bus.
4. Pair ..................................................................
Specify pairing for adjacent mixer channels.
Press the " " button, and make settings. ( p.38, 86)
Ch7–12: Select inputs for mixer chan-
nels 7–12
Here you can select the inputs for mixer channels 7–12.
Refer to "Ch1–6: Select inputs for mixer channels 1–6."