Safety Precautions - Nidec RINDCODE NRX Series Instruction Manual

Be sure to read before use
Thank you for purchasing the NIDEC-SHIMPO product. To use this product properly and safely, please be sure to read this
manual thoroughly before use. Keep this instruction manual where all users can read and/or refer to it at any time.
Before use, please carefully read these safety precautions and follow them for proper use.
This instruction manual categorizes safety precautions as DANGER, WARNING, and CAUTION according to level of importance.
Each precaution has an important explanation related to safety. Be sure to observe all precautions.
DANGER
！
！ WARNING
CAUTION
！
The type of precautions we would like you to observe is categorized using the following symbols,
・ We are not responsible for damages resulting from negligence through failure to follow the instructions set out in this manual.
・ We are not responsible for damages resulting from earthquake and/or fire unrelated to us, actions by third parties, or any other accidents,
intentional or through customer negligence, as well as from accidents caused by misuse or improper use under abnormal conditions.
・ For information regarding assurance provisions, please read the attached warranty certificate.
Do not connect this product to an power source
beyond the specified voltage range.
If you connect the product to an power source beyond the voltage
range indicated on the motor nameplate, the heated motor could
result in motor burns and fire.
Do not touch the keyway on the input and output
shafts with bare hands.
Be careful to touch the keyway. Failure to follow this could result in
injury on your hands or fingers due to the sharp edges.
Install the product on a rigid surface that is not prone
to vibration.
If the installation surface is not rigid enough, the machine could fall
over during operation or a device could be damaged due to excessive
vibration.
Do not install the product in an area with an ambient
temperature of lower than 0ºC and higher than 40ºC.
Disconnect the power supply for motor, when
connecting.
Heavy! Be careful when carrying.
Failure to follow this could result in serious injury if you drop the
product on your feet accidentally during carrying or installation.
Do not use the product in an atmosphere with a risk of
fire and/or explosion.
If you use this product in an atmosphere with risk of fire and/or
explosion, select the explosion-proof model.
Do not touch the rotating parts during operation.
Do not touch the output shaft, input shaft, or fan.
Before rotating the motor reversely, be sure to stop it completely.
T urn the power OFF during inspection.
Confirm the power source complete off before inspection
& maintenance.

Safety Precautions

Indicates a potentially hazardous situation that may result in fire, serious injuries, and/or death if you
incorrectly handle this product by neglecting the following precautions.
Indicates a potentially hazardous situation that may result in serious injury if you incorrectly handle
this product.
Indicates a potentially hazardous situation that may result in minor or moderate injury and/or property
damage if you incorrectly handle this product. However, more severe results may also occur depending
on the situation if mishandled. Be sure to observe all precautions.
and explanations are added (some examples as given below).
！
A reminder to pay close attention.
A prohibited action you must not do.
A forced action you must always do.
Precautions for installation
Precautions for operation
P re c au ti o n s f or i nspe c ti o n an d m ai n te n a n c e
Be careful of electric shock during connection.
Do not connect the product with wet (or sweaty) hands. Before wiring, be
sure to turn the power OFF. Failure to follow this could result in electric
shock.
Do not install Ringcone in a place directly exposed to
rain or water.
Failure to follow this could result in electric shock, fire, and/or
malfunction. When you use or install the product outdoors, select
an outdoor model.
Mount a safety cover on the rotational items.
Failure to follow this could result in injury on your hands or fingers
if you come into contact with the rotational items.
If you use the product in a transportation device, or
lifting device, apply protective device like brake for
safety.
To prepare pan or something for an oil leakage, if
the leaking makes serious issues on application
such as food , chemical machines, etc.
Do not touch the unit because it may become hot
during operation.
Failure to follow this could result in burns.
Avoid operation overloaded.
If you operate the unit with overload, the heated motor could result
in motor burns and/or fire.
Do not touch the unit during operation and
immediately after operation stops.
The housing temperature will not decrease immediately after
operation stops. Confirm that the temperature of the product has
decreased before touching for inspection and/or disassembly.
1