1. Manuals
  2. Brands
  3. QMS Manuals
  4. Printer
  5. 2060 WX
  6. User manual

QMS 2060 WX Print User Manual

Hide thumbs Also See for 2060 WX Print:
Table of Contents

Advertisement

Quick Links

Download this manual
QMS
2060 WX Print
®
System
User's Guide
1800457-001

Advertisement

Table of Contents
loading

Related Manuals for QMS 2060 WX Print

Summary of Contents for QMS 2060 WX Print

  • Page 1 2060 WX Print ® System User's Guide 1800457-001...
  • Page 2 Copyrighted © 1997 by QMS, Inc. All Rights Reserved. This software may not be reproduced, modified, displayed, transferred, or copied in any form or in any manner or on any media, in whole or in part, without the express written permission of QMS, Inc. Copyright Notice This manual is Copyrighted ©...

  • Page 3: Table Of Contents

    Contents Introduction About the Documentation ..........1-2 About This Manual ............. 1-2 Typographic Conventions 1-4 Printing Introduction ................ 2-2 Configuring the Windows 95 Printer Driver ....2-2 Setting the Printer Driver Defaults 2-2 Configuring the Printer Driver for the Current Print Job 2-3 Configuring Paper Options 2-4...
  • Page 4 Postcards and Thick Stock 2-62 Odd-size Paper 2-63 More About Print Media ........... 2-64 Print Media Sizes and Imageable Areas 2-64 Print Media Types, Weights, and Recommended Brands 2-66 Print Media Storage 2-66 QMS 2060 WX Print System User ’ s Guide...
  • Page 5 Setting the Ethernet Hardware Address 3-13 Using the Service Menu 3-13 Using the Board Test Menu 3-14 Printer Options Introduction ................ 4-2 Duplexer ................4-3 Memory Requirements 4-3 Installing the Duplexer 4-4 Removing the Duplexer 4-7 QMS 2060 WX Print System User ’ s Guide...
  • Page 6 Cleaning the Printer ............5-10 Cleaning Guidelines 5-10 Cleaning the Outside of the Printer 5-10 Cleaning the Inside of the Printer 5-12 Using the Maintenance Kit ..........5-14 Repacking the Printer Introduction ................ 6-2 QMS 2060 WX Print System User ’ s Guide...
  • Page 7 Jam Message Stays On 7-24 Output Problems .............. 7-24 Only Partial Pages Print 7-24 Blank Pages 7-25 Not All Pages Print 7-25 Fonts Don't Print Correctly 7-25 Frequent Media Jams 7-26 QMS 2060 WX Print System User ’ s Guide...
  • Page 8 QMS Customer Response Center (CRC) A-4 QMS World-wide Offices ..........A-5 B Technical Specifications Print Engine Specifications ..........B-2 Controller Specifications ..........B-3 Environmental Requirements .......... B-3 Print Media ................. B-4 Print Media Selection B-5 QMS 2060 WX Print System User ’ s Guide viii...
  • Page 9 Electrostatic Discharge and Your Warranty B-13 C TCP/IP Concepts Introduction ............... C-2 Terminology ..............C-2 Subnetting ................. C-4 Subnet Masks C-4 Internet Routing ..............C-5 Class A, B, and C Internet Addresses C-5 Index QMS 2060 WX Print System User ’ s Guide...

  • Page 11: Introduction

    Introduction In This Chapter . . . “About the Documentation” on page 1-2 “About This Manual” on page 1-2 “Typographic Conventions” on page 1-4...

  • Page 12: About The Documentation

    About the Documentation About the Documentation You received the following documentation with your QMS 2060 WX Print System: & QMS 2060 WX This manual contains detailed, Print System illustrated instructions to guide you as Getting Started you unpack and set up your printer,...
  • Page 13 Provides printer repacking Repacking the instructions. Printer Interprets printer and QMS Network Troubleshooting Print Monitor status messages, explains how to remove a media jam, discusses various output problems, and describes how to install the printer driver manually.

  • Page 14: Typographic Conventions

    M WARNING! Warnings indicate the possibility of personal injury if a specific procedure is not performed exactly as described in the manual. ACHTUNG! Bitte halten Sie sich exakt an die im Handbuch beschriebene Vorgehensweise, da sonst Verletzungsgefahr bestehen könnte. QMS 2060 WX Print System User ’ s Guide...

  • Page 15: Printing

    Configuring the Windows NT 4.0 printer driver on page 2-12 Sharing a printer on page 2-36 Using the QMS Network Print Monitor on page 2-40 Refilling the media cassette on page 2-45 Printing on different types of media page 2-57...

  • Page 16: Introduction

    QMS 2060 WX Print System. Configuring the Windows 95 Printer Driver This section explains how to configure the QMS 2060 WX Print System Windows 95 printer driver. Windows on-line help is also available while you’re configuring the printer driver. Just choose any Help button.

  • Page 17: Configuring The Printer Driver For The Current Print Job

    From the application’s File menu choose Print (or, in some cases, Print Setup or Page Setup). In the Print, Print Setup, or Page Setup dialog box, select the QMS 2060 WX printer driver. Choose the Properties button. Two tabs appear: Paper—Allows you to provide information about the type and...

  • Page 18: Configuring Paper Options

    The Paper tab allows you to provide information about the type and location of the media you want to print on. Each option and button is explained in detail in this section. Paper Size QMS 2060 WX Print System User’’'s Guide...
  • Page 19 Configuring the Windows 95 Printer Driver Caution: LEF refers to “long-edge feed.” All other page sizes are fed into the printer short-edge first. If you’re using LEF media, choose the page orientation in your application before you choose the media size.
  • Page 20 Tray Select Key on the printer control panel Manual Feed—The multi- purpose tray Upper Tray—The standard media cassette Lower Tray—The optional lower media cassette Default Upper Tray QMS 2060 WX Print System User’’'s Guide Universal cassette in the “upper tray” Multipurpose tray position...
  • Page 21 Configuring the Windows 95 Printer Driver Media Choice Purpose Sets the type of media to be printed Choices Standard—Normal weight paper, envelopes, and labels Thick Stock—24–43 lb (90–163 g/m ) stock Transparency—Overhead transparency film Default Standard Copies Purpose Sets the number of copies to be printed. Choices 1-999 Default...
  • Page 22 Flip on Long Edge if you want to duplex and flip the pages on the short edge, or choose Flip on Short Edge if you want to duplex and flip the pages on the long edge. QMS 2060 WX Print System User’’'s Guide...
  • Page 23 Configuring the Windows 95 Printer Driver Restore Defaults Button The Restore Defaults button allows you to reset all of the selections on the Paper tab to their default settings. OK Button The OK button allows you to save your changes and exit from the Paper—More Options window.
  • Page 24 Configuring Graphics Options The Graphics tab allows you to provide information on how the text and images in your job will be printed. Each option and button is explained in detail in this section. 2-10 QMS 2060 WX Print System User’’'s Guide...
  • Page 25 Configuring the Windows 95 Printer Driver Resolution Resolution is the measurement of the dots per inch (dpi) at which your documents are printed. Your printer is capable of printing at 300 and 600 dpi. For print jobs in which print speed is more important than print quality, you might want to select 300 dpi.
  • Page 26 Properties window. Configuring the Windows NT 4.0 Printer Driver This section explains how to configure the QMS 2060 WX Print System Windows NT 4.0 printer driver, and it describes all of the available options. Context-sensitive Windows on-line help is also available while you’re configuring the printer driver.
  • Page 27 From the Windows NT Start menu choose Settings. From the Settings menu choose Printers. In the Printers window, select the QMS 2060 WX printer icon. From the File menu choose Properties. Six tabs appear in the QMS 2060 WX Properties window: General, Ports, Scheduling, Sharing, Security, and Device Settings.
  • Page 28 Default Document Properties window. From the application’s File menu choose Print (or, in some cases, Print Setup). In the Print or Print Setup dialog box, select the QMS 2060 Choose the Properties button. Two tabs appear in the QMS 2060 WX Document Properties window: Page Setup—Allows you to provide information about paper...
  • Page 29 Windows NT 4.0 Printer Driver Configuring Device Settings Device Settings is the sixth tab in the QMS 2060 WX Properties dia- log box. The QMS 2060 WX Device Settings tree has two branches: Form To Tray Assignment—Upper Paper tray, Manual Paper feed, Lower Paper tray, and Printer Default.
  • Page 30 Lower Tray—The optional lower media cassette See the “Notes” section at the bottom of this table for a list of the choices for each of these trays. Default No defaults 2-16 QMS 2060 WX Print System User’’'s Guide...
  • Page 31 Configuring the Windows NT 4.0 Printer Driver Notes Select an option (subbranch) to display the choices for that option. The choices appear in a lower window. Then select a form (media size) for the selected option. The selected form (media size) will appear in the upper window beside the name of the option.
  • Page 32 Halftone Setup... button at the bottom of the dialog box. Choose this button to display the Device Color / Halftone Properties dialog box. QMS has carefully set the default values of the parameters in the Device Color / Halftone Properties dialog box to provide optimum performance with the QMS 2060 WX.
  • Page 33 Configuring the Windows NT 4.0 Printer Driver Halftone Pattern Purpose Specifies the cell size for the pattern. Choices 2x2, 2x2 Enhanced, 4x4, 4x4 Enhanced, 6x6, 6x6 Enhanced, 8x8, 8x8 Enhanced, 10x10, 10x10 Enhanced, 12x12, 12x12 Enhanced, 14x14, 14x14 Enhanced, 16x16, 16x16 Enhanced Default 6x6 Enhanced Notes...
  • Page 34 The range (25.00 to 400.00) scales the entire device-output color darker or brighter by stretching device colors over a smaller or larger range. 2-20 QMS 2060 WX Print System User’’'s Guide...
  • Page 35 Configuring the Windows NT 4.0 Printer Driver Default Button The Default button allows you to reset all of the selections in the Device Color / Halftone Properties window to their default settings. Revert Button The Revert button allows you to reset all of the selections in the Device Color / Halftone Properties window to the values in use when the window was opened.
  • Page 36 Each option and button is explained in this section. » Note: The Page Setup and Advanced tabs display in both the QMS 2060 WX Default Document Properties and the QMS 2060 WX Document Properties dialog boxes. Since the tabs are the same in both dialog boxes, only the Document Properties dialog box is shown here.
  • Page 37 Configuring the Windows NT 4.0 Printer Driver Paper Size Caution: LEF refers to “long-edge feed.” All other page sizes are fed into the printer short-edge first. If you’re using LEF media, choose the page orientation in your application before you choose the media size.
  • Page 38 Automatically Select—Any cassette or tray that contains the requested media size Default Automatically Select Copy Count Purpose Sets the number of copies to be printed. Choices 1-999 Default 1 Copy 2-24 QMS 2060 WX Print System User’’'s Guide...
  • Page 39 Configuring the Windows NT 4.0 Printer Driver Orientation Caution: If you’re using LEF media, choose the page orientation in your application before you choose the media size. This ensures proper printed output (and the proper icon in applications such as Microsoft Word that display media icons in the Page Setup dialog box).
  • Page 40 To change an option setting, select an option. Under that option is dis- played a list of selections. Just select a setting to display it inside the angle brackets beside the option. 2-26 QMS 2060 WX Print System User’’'s Guide...
  • Page 41 Windows NT 4.0 Printer Driver » Note: The Page Setup and Advanced tabs display in both the QMS 2060 WX Default Document Properties and the QMS 2060 WX Document Properties dialog boxes. Since the tabs are the same in both dialog boxes, only the Document Properties dialog box is shown here.
  • Page 42 Notes If a media size other than that chosen in the driver is installed in the cassette, an error message displays, but the job still prints on the currently installed media size. 2-28 QMS 2060 WX Print System User’’'s Guide...
  • Page 43 Configuring the Windows NT 4.0 Printer Driver Orientation Caution: LEF refers to “long-edge feed.” All other page sizes are fed into the printer short-edge first. If you’re using LEF media, choose the page orientation in your application before you choose the media size.
  • Page 44 Media Branch Document Options Purpose Sets the type of media to be printed Choices Standard—Normal weight paper, envelopes, and labels Thick Stock—24–43 lb (90–163 g/m ) stock Transparency—Overhead transparency film Default Standard 2-30 QMS 2060 WX Print System User’’'s Guide...
  • Page 45 Configuring the Windows NT 4.0 Printer Driver Metafile Spooling Branch Document Options Purpose Sets the format in which printing information is stored while a print job is waiting. Choices Off—Turns off metafile spooling On—Turns on metafile spooling Default Notes Generally, Metafile Spooling On (EMF format) frees up your program because it is smaller and doesn’t depend on what kind of printing device you have.
  • Page 46 Color Adjustment window displays. Each option and button on this window is explained in detail in this section. Contrast Purpose Sets the difference between dark and bright areas in your picture. Range -100 (darkest) to +100 (brightest) Default 2-32 QMS 2060 WX Print System User’’'s Guide...
  • Page 47 Configuring the Windows NT 4.0 Printer Driver Brightness Purpose Sets the intensity of the light in your picture. Range -100 (darkest) to +100 (lightest) Default Color This option is grayed out to indicate that it is not available on mono- chrome printers.
  • Page 48 Linear=1.0 check box—Selecting this check box disables the Red, Green, and Blue scroll boxes and sets each input RGB gamma correction to 1.000 (brightness equal to input value). 2-34 QMS 2060 WX Print System User’’'s Guide...
  • Page 49 Configuring the Windows NT 4.0 Printer Driver Picture Purpose Selects a predefined test picture. Choices 1: Reference Colors 6x4,24@8—>546x247 2: RGB Test Colors 36x33,256@8—>546x247 3: NTSC Color Bar 28x21,16@4—>546x247 Default RGB Test Colors Notes Available only if the View Picture Check Box is selected. The numbers to the right of the test picture identify the original size (in pixels), number of colors, type of color, and current dis- play size of the graphic that is being used as a test picture.
  • Page 50 Ethernet network Windows 95 » Note: This section explains how to configure the QMS 2060 WX printer driver in Windows 95 for sharing. If you’re using Windows NT 4.0, refer to “Windows NT 4.0” on page 2-38.
  • Page 51 Printer Sharing From the Windows 95 Start menu choose Settings. From the Settings menu choose Printers. In the Printers window, select QMS 2060 WX icon. From the File menu choose Sharing. » Note: If Sharing isn’t available, do the following to add File and Printer Sharing services: From the Windows 95 Start menu choose Settings.
  • Page 52 In the Alternate Drivers list box, select the Windows 95 operating system and choose OK. If the operating system on your PC does not have the QMS 2060 WX printer driver for Windows 95, you will be prompted to install it. Insert the QMS 2060 WX printer driver disk for Windows 95 and choose OK.
  • Page 53 **Client PC **Client PC **Client PC *The QMS 2060 WX printer driver must be installed on the server. **Client PCs supported are Windows 95 and Windows NT 4.0 configured. When connected to a Windows NT 4.0 server, the QMS 2060 WX printer driver is automatically downloaded to any requesting client PC that is running Windows 95 or Windows NT 4.0.
  • Page 54 Print to this printer just as if it were connected directly to your PC. Using a Network Print Monitor The QMS Network Print Monitors for Windows 95 and Windows NT 4.0 control the printing environment for both local and remote print jobs submitted through shared resources.
  • Page 55 LOCALMON print monitors. **LPRMON is present only on Windows NT systems. Components The QMS Network Print Monitor has three main components: Status Component This component obtains information from the printer, such as print job “go/nogo” and error or warning conditions. Status...
  • Page 56 This component transports print jobs to a specific QMS Crown print device. When a job is sent to a print device by the QMS Net- work Print Monitor, it utilizes all allocated Windows 95 operating system resources to transport the job. If a connection is broken while a job is being transported, the monitor discards the remain- ing data and gives control back to the Print Monitor Print Spooler.
  • Page 57 About the QMS Network Print Monitor Windows 95 Use the following procedure to obtain status information on a print job: From the Start menu choose Settings. From the Settings menu choose Printers. Double-click the icon of printer icon. Whenever a print job is sent to that port, its status is reported in a...
  • Page 58 From the Start menu choose Settings. From the Settings menu choose Printers. Double-click the icon of printer icon. Whenever a print job is sent to that port, its status is reported in a status window: 2-44 QMS 2060 WX Print System User’’'s Guide...
  • Page 59 See chapter 7, “Troubleshooting,” for more information on the status messages that display. Refilling the Media Cassette The QMS 2060 WX Print System comes standard with a 250-sheet universal cassette. However, optional 250-sheet (letter/A4 or univer- sal) and 500-sheet (letter/A4 only) cassettes are also available.
  • Page 60 Remove the top and bottom sheets The top and bottom sheets sometimes have residual glue buildup that could cause the printer to jam. 2-46 QMS 2060 WX Print System User’’'s Guide...
  • Page 61 Refilling the Media Cassette Loading the Paper 250-sheet Universal Cassette » Note: Reload the media cassette only when it’s empty. Pull out and remove the cassette. Open the paper cover. Printing 2-47...
  • Page 62 Lay the cassette flat on a hard surface and, using your left hand, push down on the plate in the cassette until it locks. Adjust the paper guides to fit the paper size. 2-48 QMS 2060 WX Print System User’’'s Guide...
  • Page 63 Refilling the Media Cassette Load the media face up in the cassette. » Note: To optimise print speed for letter/A4 size media, you must load the media for long-edge feed (LEF) and select Letter LEF or A4 LEF as the media size in the printer driver. See the sections on configuring the printer driver at the beginning of this chapter for more information.
  • Page 64 Adjust the media stop to fit the media size. Your output is delivered print-side down to the output tray at the top of the printer. The media stop keeps the sheets positioned correctly. Media Stop 2-50 QMS 2060 WX Print System User’’'s Guide...
  • Page 65 Refilling the Media Cassette 500-sheet Cassette » Note: Reload the media cassette only when it’s empty. Pull out and remove the cassette. Position the cassette. The cassette has a spring in the bottom that provides some resistance when print media is placed on it. Lay the cassette flat on a hard surface and, using your left hand, push down on the plate in the cassette until it locks.
  • Page 66 Halfway to the top limit mark. Up to the top limit mark. Retaining Clips Top Limit Bottom Limit Ensure that the media stack lies flat and does not exceed the top limit mark. 2-52 QMS 2060 WX Print System User’’'s Guide...
  • Page 67 Refilling the Media Cassette Slide the cassette back into the upper cassette feeder until it’s firmly seated. Pull out the media stop and slide it to the correct media size. Media Stop » Note: When printing different-sized media in the face-down tray, set the print tray to the largest paper size.
  • Page 68 (manual-feed) tray and the media type you plan to use (paper or transparency). Use your application’s print setup feature to select any other printing options you want. Open the multipurpose tray. 2-54 QMS 2060 WX Print System User’’'s Guide...
  • Page 69 Refilling the Media Cassette Adjust the media guides on the multipurpose tray to match the width of the media you are using. Align the media, and insert it print side up between the media guides, sliding it as far as it will go in the printer. »...
  • Page 70 For large size media, leave the tray cover open. » Note: Do not load additional media until all the sheets in the multipurpose tray have been fed through the printer. Adjust the media stop for proper media delivery. Media Stop 2-56 QMS 2060 WX Print System User’’'s Guide...
  • Page 71 ° ° (200 C/392 F). We recommend QMS (p/n 1710118-002) A4 transparencies. Insert the transparencies short-edge first, printing side up with the top of the page on the left side of the tray. The correct print side is usually marked on the transparency package.
  • Page 72 Load the labels long edge first, face up, and with the top of the page toward the rear of the printer. Printing Format the labels in your application. 2-58 QMS 2060 WX Print System User’’'s Guide...
  • Page 73 Printing on Different Types of Media Load the labels in the printer. See “Multipurpose Tray” on page 2-54 and “Special Considera- tions,” above, for information on loading labels. » Note: You may want to try printing the formatted information on a plain sheet of paper first to check placement.
  • Page 74 Envelopes with transparent windows or peel-off strips. Envelopes with fasteners or clasps. Envelopes with edges that aren’t square and envelopes that are wrinkled, torn, or curled. 2-60 QMS 2060 WX Print System User’’'s Guide...
  • Page 75 Printing on Different Types of Media Envelopes made of any material that melts, vaporizes, off- sets, discolors, or emits dangerous fumes at high tempera- tures (190° C/ 374° F). Use landscape orientation to create the envelope text in your application. Leave a 0.16" (4.06 mm) margin around the edges of the envelope.
  • Page 76 Use only 24 to 42 lb (90 to 157 g/m ) postcards and thick stock. Adjust the multipurpose tray guides to fit the media size. Load the postcards or thick stock short edge first with the printing surface up. 2-62 QMS 2060 WX Print System User’’'s Guide...
  • Page 77 Printing on Different Types of Media Printing Format the text in your application. Load the postcards or thick stock, following the same proce- dure as for loading envelopes on page 2-61. » Note: You may want to try printing the formatted information on a plain sheet of paper first to check placement.
  • Page 78 Print Media Sizes and Imageable Areas The following table lists the size, imageable area, feed edge (the edge of the media drawn into the printer first), and input sources of all sup- ported media sizes. 2-64 QMS 2060 WX Print System User’’'s Guide...
  • Page 79 If the text/image in your document gets cut off (doesn’t print to the expected margins), it may be due to an imageable area constraint. The imageable areas for print media on your QMS 2060 WX Print System are not centered vertically on the page and may vary "...
  • Page 80 Keep media in good condition by storing it In its wrapper On a flat surface In a closed cabinet In a cool, dry area 2-66 QMS 2060 WX Print System User’’'s Guide...
  • Page 81 Preventing Media Jams Preventing Media Jams Some printer problems are caused by improper handling of media or use of the wrong media and consumables. There are several things you can do to reduce the occurrence of media jams. Use paper, envelopes, labels, postcards, transparencies that match the printer specifications.(See the “Consumable Supplies”...
  • Page 82 Note: Since all pages of a multi-page print job may not have been received by the printer at the time you’re trying to cancel the job, you may have to cancel the job both at the printer and at your PC. 2-68 QMS 2060 WX Print System User’’'s Guide...
  • Page 83 Control Panel In This Chapter . . . Message window on page 3-3 Control panel indicators on page 3-4 Function keys on page 3-5 Printer configuration on page 3-6...
  • Page 84 It allows you to configure several printer features The control panel consists of a message window, six LED indicators, and nine keys. Each of these is discussed in the following sections. Idle QMS 2060 WX Print System User ’ s Guide...
  • Page 85 About the Control Panel About the Control Panel The Message Window The message window provides two functions: It displays status and error information. See chapter 7, “Trouble- shooting,” for an annotated list of status and error messages. It displays configuration options. Configuration is discussed later in this chapter.
  • Page 86 Blinking—The printer is receiving data from the PC. On—An optional printer hard disk is being accessed. Blinking—System software is being downloaded to FLASH. On—An error message is displayed in the message window. QMS 2060 WX Print System User ’ s Guide...
  • Page 87 (The “Copy” portion of the key isn’t used. It’s available if you upgrade your printer to a QMS 2060 BX, GX, or EX Print System. Contact your QMS vendor for specifications and purchase information.) Press this key to find out the number of page faces that have been printed.
  • Page 88 Most of the configuration is done in this way. See chapter 2, “Printing.” Through the printer control panel—Several options are availa- ble. The rest of this section explains how to use the configuration menu. QMS 2060 WX Print System User ’ s Guide...
  • Page 89 Printer Configuration The Configuration Menu Idle Press the Menu key to move through the menus. 1 hr Energy saver 2 hr 15 min 30 min 45 min English Language German French Italian Spanish Dutch 000.000.000.000 Internet address Subnet mask 000.000.000.000 000.000.000.000 Router 1 000.000.000.000...
  • Page 90 (Service and Board Test have different functions. They are explained in chapter 7, “Troubleshooting.”) Select Save an option. Next Advance to the next option within a menu. Previous Return to the previous option within a menu. QMS 2060 WX Print System User ’ s Guide...
  • Page 91 Printer Configuration For example, the instructions below show how to change the Energy Saver time interval from 1 hour to 15 minutes. Press to... The message this key... window reads... Online/ Turn off the Online indicator and Idle Offline ready the printer for configuration.
  • Page 92 Printer Configuration Setting Energy Conservation The QMS 2060 WX Print System is Energy Star compliant. The Energy Saver menu allows you to specify whether the printer changes to a low-power state (the engine remains on, but the fuser turns off) after the printer is inactive for a specified length of time.
  • Page 93 Printer Configuration Setting the Subnet Mask The Subnet Mask menu allows you to set the printer’s subnet mask. The address is in the format xxx.xxx.xxx.xxx. Menu Subnet mask Choices Each xxx.xxx.xxx.xxx triplet can have a value of 001– 254. Default 000.000.000.000 n If subnets are not used with your network, the sub- Notes...
  • Page 94 (for example, 1 is entered as 001, and 9 is entered as 009). n Any xxx value between 10 and 99 must begin with 0 (for example, 10 is entered as 010, and 99 is entered as 099). 3-12 QMS 2060 WX Print System User ’ s Guide...
  • Page 95 Printer Configuration Setting the Communications Port The Communications menu allows you to select a communications interface port. Menu Communications Choices Parallel port, Ethernet Default Parallel port Notes Once you save your changes to this menu, the printer automatically reboots. Setting the Ethernet Hardware Address The Eth.
  • Page 96 Printer Configuration Using the Board Test Menu The Board Test menu allows you to test the printer. For complete information, see “Performing a Board Test” in chapter 7, “Trouble- shooting.” 3-14 QMS 2060 WX Print System User ’ s Guide...
  • Page 97 Printer Options In This Chapter . . . Available options and accessories on page 4-2 Duplexer on page 4-3 Additional media cassettes on page 4-8 Optional feeder on page 4-9 Single In-line memory modules (SIMMs) on page 4-12 Updating system software on page 4-19 Updating the printer driver on page 4-20...
  • Page 98 Introduction Introduction The following options are available for your printer. Contact your QMS vendor for purchase information. 2060 BX, GX, EX Workgroup printer with Centronics/IEEE 1284 Upgrade bidirectional parallel and QMS CrownNet Ethernet ((EtherTalk, LAN Manager/LAN Server, NetWare, TCP/IP) interfaces as well as an optional interface...

  • Page 99: Duplexer

    Memory Requirements Your QMS 2060 WX Print System standard comes with 8 MB of memory. This allows you to simplex print on all media sizes and duplex print on A5 and Statement media sizes. Duplex printing on other media sizes, however, requires more memory.
  • Page 100 Remove the duplexer from its box, and then remove all the packing materials. Turn off the printer, and remove the power cord and all inter- face cable(s). Remove the panel for the duplex drive section on the back of the printer. QMS 2060 WX Print System User ’ s Guide...
  • Page 101 Duplexer Attach the two duplex brackets (J-hooks, included with the duplexer) to the back of the printer in the holes provided. » Note: Press down until you hear a click. Hook the duplexer onto the brackets. Printer Options...
  • Page 102 Duplexer Position the duplexer in place over the panel and the bracket. Secure the duplexer in place with the two screws. QMS 2060 WX Print System User ’ s Guide...
  • Page 103 Duplexer Reconnect the interface cables, plug in the power cord, and turn on the printer. Check the message window to make sure the printer is ready to print. 10 Configure the printer for duplex printing through the printer driver. See chapter 2, “Printing,” for details. Removing the Duplexer Turn off the printer.

  • Page 104: Additional Media Cassettes

    Keep replacement cassettes close by, and you can easily change media by slipping one cas- sette out and another in. Increased media-feed capacity (requires installation of an optional feeder). QMS 2060 WX Print System User ’ s Guide...

  • Page 105: Optional Feeder

    Optional Feeder Optional Feeder The printer and standard feeder are stacked on top of the optional feeder, so no additional space is necessary. It comes with either a 500-sheet letter/A4 cassette or a second 250-sheet universal media cassette. The optional feeder provides two benefits: It increases your printer’s media-feed capacity to a total of 900 or 1150 sheets, depending on whether you install an optional 250- sheet or 500-sheet cassette.
  • Page 106 Place the optional feeder in the appropriate location. WARNING! The printer is heavy, so two people should lift it. ACHTUNG! Enternen Sie den Netzstecker und lassen Sie die Heizung abkühlen, bevor Sie den Drucker reinigen. 4-10 QMS 2060 WX Print System User ’ s Guide...
  • Page 107 Optional Feeder Using the carrying grips located on the sides of the standard feeder, set the printer and standard feeder on the optional feeder, using the coupling pins as guides. » Note: Align the printer over the pins on the optional feeder, and set the printer down on the optional feeder so that the three positioning posts on the optional feeder fit into the holes on the printer’s bottom.

  • Page 108: Single In-Line Memory Modules (Simms)

    32 MB SIMM will not work correctly. See FAQ 7191 for a list of each approved SIMM, its manufacturers and part numbers, and the QMS products on which it can be used. You can access QMS FAQs through the Internet at http://www.qms.com/www/faq/ or through Q-FAX (see appendix A,...
  • Page 109 Single In-Line Memory Modules (SIMMs) Sie den Drucker aus und ziehen Sie den Netzstecker heraus bevor Sie die Druckerabdeckung öffnen. Caution: This hardware change automatically restores defaults. It's very important to protect the controller board from electrostatic damage while performing this task. If an anti-static wrist strap is provided in your printer option kit, attach one end of it to your wrist and the other end to any convenient electrical ground (for example, the bare metal chassis of equipment,...
  • Page 110 If necessary, remove an existing SIMM. Release the SIMM. Pull the latches on each side of the SIMM connector outward using both thumbs. 4-14 QMS 2060 WX Print System User ’ s Guide...
  • Page 111 Single In-Line Memory Modules (SIMMs) Remove the SIMM. Tilt the SIMM backwards to a 45° angle away from the SIMM connector, and then lift it out. Remove the new SIMM from the anti-static bag. Printer Options 4-15...
  • Page 112 » Note: You can insert a SIMM in either SIMM connector as long as DRAM0, and the SIMM connector before the one you’re installing, is occupied. 4-16 QMS 2060 WX Print System User ’ s Guide...
  • Page 113 Single In-Line Memory Modules (SIMMs) Tilt the SIMM up to a 90° angle until you feel it snap into place. When seated, the SIMM stands upright, firmly in place. If you cannot snap the SIMM into place, do not force it. Reposition it, making sure that the bottom of the SIMM is seated completely in the connector.
  • Page 114 13 Reconnect the interface cable(s) and the power cord, and then turn on the printer. The amount of memory installed and the system software version are displayed in the control panel message window as the printer starts up. 4-18 QMS 2060 WX Print System User ’ s Guide...

  • Page 115: Updating System Software

    If necessary, connect the printer to the PC’s parallel port. Turn on the PC and the printer. Insert the QMS 2060 WX system software disk in the PC’s 3.5" disk drive. From the Windows 95 or Windows NT Start menu choose Run...

  • Page 116: Updating The Printer Driver

    “Ethernet Connections” on page 4-21. Parallel Connections Windows 95 and the parallel port on the QMS 2060 WX both support Plug and Play technology, which lets your PC and its attached devices work together automatically. The correct printer driver is automatically selected for you when you perform the following procedure.
  • Page 117 A message window informs you New Hardware Found, and then you’re prompted to insert the printer driver disk. Insert the QMS 2060 printer drivers disk or CD-ROM (shipped with your printer) in the appropriate disk drive on your PC, and choose OK to continue.
  • Page 118 From the File menu, choose Delete. Select Yes when you’re asked if you’re sure you want to delete the printer. Insert the QMS 2060 WX printer driver disk into the PC’s 3.5" disk drive. In the Windows NT Start menu choose Settings.
  • Page 119 12 In the Install from Disk dialog box, type drive:\ (where drive is the letter of the disk drive in which you inserted the QMS 2060 WX printer driver disk in step 5), and choose OK. QMS 2060 WX printer displays in the list box.
  • Page 120 The required files are copied to the appropriate directory. » Note: When the QMS 2060 WX is connected to a Win- dows 95 server, the printer driver must be installed on the server and on every client PC. (Refer to the QMS 2060 WX Print System Setup Guide for more information.)
  • Page 121 Maintenance In This Chapter . . . Handling the printer on page 5-2 About toner cartridges on page 5-4 Replacing toner cartridges on page 5-6 Cleaning the printer on page 5-10...
  • Page 122 Don’t leave the printer open for any length of time, especially in well-lit places; light may damage the toner cartridge. Don’t open the printer during printing and do not tap paper stacks on the printer. Don’t tilt, lubricate, or disassemble the printer. QMS 2060 WX Print System User’’'s Guide...
  • Page 123 Handling the Printer Don’t touch the electrical contacts, gears, or laser beam devices. Doing so may damage the printer and cause the print quality to deteriorate. Keep media in the output tray at minimum level. If the media stacks too high, your printer may experience media jams and excessive media curl.
  • Page 124 Ordering Toner Cartridges Choosing the right consumables for your QMS 2060 WX Print System will not only increase its reliability and performance, but also minimize the risk of damage. Only QMS toner cartridges are designed to meet the exact specifications of your QMS printer, guaranteeing maximum performance, efficiency, and long life.
  • Page 125 About Toner Cartridges Handling Toner Cartridges The cartridge contains the toner and laser-sensitive drum needed to operate the laser printer. The cartridge has a wide opening for the laser beam guided via the reflecting mirror. Be careful not to drop any foreign objects, such as clips or pins into the cartridge, when handling and install- ing the cartridge.
  • Page 126 Note: Put the old toner cartridge in a trash receptacle. Do not dispose of it by burning. Remove any residual toner powder from inside the printer. See “Cleaning the Inside of the Printer” on page 5-12. QMS 2060 WX Print System User’’'s Guide...
  • Page 127 About Toner Cartridges Lift the toner cartridge out of its shipping carton, open the aluminum protective bag, and remove the cartridge. Caution: The toner cartridge is sensitive to bright light. Do not remove the cartridge from the printer until you’re ready to return it to its protective bag.
  • Page 128 Pull the plastic strip straight out. If the strip breaks, grasp the clear part of the tape seal and pull it straight out. Discard the strip and the tape seal. QMS 2060 WX Print System User’’'s Guide...
  • Page 129 About Toner Cartridges Slide the toner cartridge in the printer. Holding the handle of the toner cartridge with your right hand, so the arrow on the toner cartridge is facing away from you, angle the cartridge down into the printer. Place the cartridge on the rails inside the upper unit of the printer, and gently slide it straight down until it is firmly seated.
  • Page 130 Cleaning the Outside of the Printer M WARNING! Turn off the printer, unplug the power cord, and disconnect any interface cables before cleaning. ACHTUNG! Ziehen Sie den Netzstecker aus der Steckdose bevor Sie den Drucker reinigen. 5-10 QMS 2060 WX Print System User’’'s Guide...
  • Page 131 Cleaning the Printer To protect and maintain the appearance of your printer, wipe the cover and external parts with a soft cloth moistened with water or mild detergent. M WARNING! Do not spill water or detergent into the printer; otherwise the printer will be damaged and an electric shock may occur.
  • Page 132 Note: If you plan to reinstall the toner cartridge, put it back in its aluminum bag or in a desk drawer, or cover it with a thick cloth while cleaning the interior of the printer. The toner cartridge can be damaged by exposure to light. 5-12 QMS 2060 WX Print System User’’'s Guide...
  • Page 133 Cleaning the Printer Clean the window glass of the print head using a soft cloth. » Note: You can see the window glass if you face the printer from its rear. If the glass is especially dirty, use a cloth dampened with ethyl alcohol.
  • Page 134 Using the Maintenance Kit In order to keep your printer in optimim printing condition, we recom- mend that you contact your local QMS Service provider or QMS Sup- plier after every 120,000 page faces printed to order a maintenance kit. (A page face is one side of a sheet of media. Therefore, a simplex page has one printed face while a duplex page has two printed faces.)
  • Page 135 Repacking the Printer In This Chapter . . . Repacking the printer for relocation or shipment on page 6-2...
  • Page 136 Introduction Introduction If you need to relocate or ship your QMS 2060 WX Print System after it has been installed, you must follow the procedures in this chapter to prevent damage to the printer and to keep your warranty valid.
  • Page 137 Remove the Toner Cartridge Remove the Toner Cartridge Press the upper unit lock release button, and open the top cover. Remove the toner cartridge. While grasping the handle of the empty toner cartridge, remove the cartridge by pulling up it and then towards you.
  • Page 138 Get someone to help you with this step: Lift the printer back into its original shipping carton. » Note: If you’re returning the printer for service, you don’t need to return the toner, paper cassette(s), sheet feeder, power cable, or interface cables. QMS 2060 WX Print System User ’ s Guide...
  • Page 139 Troubleshooting In This Chapter . . . Status messages on page 7-2 Miscellaneous problems on page 7-11 Testing the printer board on page 7-13 Accessing the page count on page 7-14 Media jams on page 7-15 Control panel problems on page 7-24 Output problems on page 7-24 Print quality problems on page 7-26 Printer driver manual installation on page 7-32...

  • Page 140: Status Messages

    5 minutes, then turn it back on. This often clears the error message indicator and printer operation resumes. Always try this before making a service call. QMS 2060 WX Print System User’’'s Guide...
  • Page 141 Printer Status Messages This message... indicates... » Note: Shaded table cells indicate that the message scrolls. There is an application specific Asic error integrated circuit (ASIC) problem. Call for service. You have made an illegal entry in the Bad entry configuration menu.
  • Page 142 (see “Placing a Service Call” on page 7-33). The Ethernet hardware address is not HW err 0 cancel set. Use the Eth. HW address menu to set it (see chapter 3, “Control Panel). QMS 2060 WX Print System User’’'s Guide...
  • Page 143 This indicates the amount of memory x Meg ver x.x installed in the printer and the system software version. It displays immediately after QMS 2060 WX test during printer startup. Media has jammed leaving the media Misfeed jam cassette. Remove the jam (see “Media Jams”...
  • Page 144 The printer is going through its initial QMS 2060 WX test testing during startup. You have selected a setting or option in Selected the configuration menu. QMS 2060 WX Print System User’’'s Guide...
  • Page 145 Printer Status Messages This message... indicates... » Note: Shaded table cells indicate that the message scrolls. The toner cartridge is empty. (See Toner empty chapter 5, “Maintenance,” for information on replacing the toner cartridge.) The toner cartridge is low. (See chapter Toner low 5, “Maintenance,”...
  • Page 146 The spooler is ready to activate the des- Printing ignated monitor and despool the sub- mitted print job. The spooler has finished submitting the Deleting print job to the designated print monitor and is deleting the spool file. QMS 2060 WX Print System User’’'s Guide...
  • Page 147 Print Monitor Status Messages This indicates... Do this... message... The spooler is reporting an error Error received from the monitor. n For print jobs n If the print job is spooled on a local spooled on a local workstation, then a dialog box workstation, click prompting you to either delete or the appropriate...
  • Page 148 Print Monitor Status Messages Monitor Status Information One of the following messages displays via Print Manager in the printer status window when the QMS Network Print Monitor is the originator of the status information: This indicates... Do this... message... n If the print job is The QMS Network Print Monitor can’t...
  • Page 149 Printer Status Information This printer-dependent status information displays via Print Manager in the printer status window when the QMS Network Print Monitor is displaying a message from the printer. See “Printer Status Messages” on page 7-2 for a complete list and description of these messages.
  • Page 150 Is your application set up correctly for printing? Are the commu- nication parameters the same as those on your host and printer? If you still can’t identify the problem, contact your QMS vendor. Does your application require any additional printer setup? If you’re experiencing printing problems not related to print quality,...
  • Page 151 Performing a Board Test Performing a Board Test You can test the printer by using the Board Test menu. Caution: Make sure the control panel message window reads IDLE before performing this procedure. Press the Online/Offline key to take the printer off line. Press the Menu key 10 times to access the Board Test menu.
  • Page 152 Press the Select key. The message Page count # xxx scrolls in the control panel message window. Press the Online/Offline key to return the message window to Idle and put the printer back on line. 7-14 QMS 2060 WX Print System User’’'s Guide...

  • Page 153: Media Jams

    Media Jams Media Jams When a jam occurs, the message window on the control panel displays one of the following messages: Inner jam, Misfeed jam, or Outer jam. This section contain procedures for clearing each type of jam. Locating Print Media Jams When print media jams occur, a message displays in the message win- dow.
  • Page 154 ACHTUNG! Die Fixiereinheit und die Papierführung werden sehr heiß, wenn der Drucker in Betrieb ist; bei Berührung dieser Partien besteht Verletzungsgefahr! Open the upper unit. Remove the toner cartridge. 7-16 QMS 2060 WX Print System User’’'s Guide...
  • Page 155 Media Jams If the edge of the media hasn’t been fed in the fusing unit, open the front transport guide and pull the jammed media upward and then out. Front Transport Guide If the edge of the media has been fed into the fusing unit, pull the jammed paper forward and out.
  • Page 156 Media Jams Reinstall the toner cartridge. Close the upper unit. Clearing Cassette Area Jams Open the upper unit. 7-18 QMS 2060 WX Print System User’’'s Guide...
  • Page 157 Media Jams Remove the toner cartridge. Determine which media cassette is currently being used, and remove it. Check the cassette pick-up roller area, and remove any jammed print media that remains outside the main unit. Troubleshooting 7-19...
  • Page 158 Note: Leaving print media in the multipurpose tray can cause the print media position to shift during removal of the jam. This may result in a media feed failure and another jam when printing is restarted. Open the upper unit. 7-20 QMS 2060 WX Print System User’’'s Guide...
  • Page 159 Media Jams Remove the toner cartridge. Open the multipurpose tray, and pull out the jammed media. Troubleshooting 7-21...
  • Page 160 Media Jams Reinstall the toner cartridge. Close the upper unit. 7-22 QMS 2060 WX Print System User’’'s Guide...
  • Page 161 Media Jams Clearing a Duplexer Media Jam Open the duplex cover and pull out the jammed paper. Open the maintenance cover and remove the jammed paper. Maintenance Cover Close the maintenance cover and the duplexer. Troubleshooting 7-23...

  • Page 162: Control Panel Problems

    The job may have been too complex for the amount of memory currently installed in the printer. You have three options: Change to Coarse dither in the printer driver Print at 300 dpi Add more memory 7-24 QMS 2060 WX Print System User’’'s Guide...
  • Page 163 If these solutions do not work, contact your QMS vendor to purchase another toner cartridge. Not All Pages Print If the printer stops printing in the middle of your file, try the following: Check your cable.

  • Page 164: Print Quality Problems

    The following list includes several image defects with possible solu- tions. Try the solutions in the sequence given. If the solutions listed don’t solve the problem, place a service call to your QMS vendor. See “Placing a Service Call” on page 7-33.
  • Page 165 Listed below are several print quality problems with possible solu- tions. Try the solutions in the sequence given. If the solutions listed do not solve the problem, place a service call to your QMS vendor. Black Image (Entire Page) n The toner cartridge may be defective.
  • Page 166 Printout Too Dark n The toner cartridge may be defective. Install a new toner cartridge, if necessary. Printout Too Light n The toner may need to be redistributed. Remove the toner cartridge and rock it as you would when installing a new cartridge. This redistributes toner inside the cartridge.
  • Page 167 Print Quality Problems Toner Smudges n If the toner smudges are only on the front of the page, do the following: 1 Distribute the toner. 2 Make sure the toner cartridge is not defective. 3 If steps 1 and 2 above do not solve the problem, install a new toner cartridge.
  • Page 168 Toner does not adhere well to paper at the positions where it has become wet. Replace the paper in the tray or cassette with dry paper, and retest for irregular print. 7-30 QMS 2060 WX Print System User’’'s Guide...
  • Page 169 Print Quality Problems White (or Black) Stripes n The window glass of the Print Head may be dirty. Clean the glass as described in chapter 4, “Printer Care.” n The toner cartridge may be defective. Install a new toner cartridge, if needed. White (or Black) Bands n The toner cartridge may be defective.
  • Page 170 From the Start menu, choose Settings. From the Settings menu, choose Control Panel. In the Control Panel dialog box, choose Add/Remove Pro- grams. On the Install/Uninstall tab select QMS Print Monitor. Choose Add/Remove. In the Welcome window, choose OK. 7-32...

  • Page 171: Placing A Service Call

    Print Monitor. » Note: All files that are associated with the Print Monitor installation and all QMS ports which were associated with the Print Monitor are removed. Placing a Service Call If you have a problem you can’t resolve, contact your QMS vendor.
  • Page 172 What is your printer model and serial number? What operating system do you have and what version? What application(s) are you using? What is the QMS 2060 WX Print System printer driver ver- sion (choose the About button on the driver’s Paper tab)? 7-34 QMS 2060 WX Print System User’’'s Guide...
  • Page 173 QMS Customer Support In This Appendix . . . Sources of customer support on page A-2 QMS world-wide offices on page A-3...
  • Page 174 The QMS server provides access to technical reports, new product announcements, a trade show schedule, and other general informa- tion about QMS. If you have access to the World Wide Web, you can view the QMS home page at http://www.qms.nl/. The QMS ftp resource is ftp.qms.com.
  • Page 175 QMS World-wide Offices QMS World-wide Offices QMS United States and Latin America General Contact 1 (334) 633-4300 Fax 1 (334) 633-4866 Email info@qms.com Customer Response Center (CRC) Technical Assistance 1 (334) 633-4500 7:00 am–6:00 pm Central Time Bulletin Board Service...
  • Page 176 QMS GMBH Willstätterstrasse 10 40549 Düsseldorf Germany and Germany Austria (+49) 211–596 1333 Fax (+49) 211–596 1397 QMS Italy Via della Repubblica 56 43100 Parma Italy (+39) 52–1231 998 Fax (+39) 52–1232 902 QMS 2060 WX Print System User's Guide...
  • Page 177 Peltier Road, Sunninghill, Johannesburg Republic of South Africa (+27) 11–807 6957 Fax (+27) 11–807 6960 QMS UK Old Bridge House, The Hythe Staines, Middlesex TW18 3JF United Kingdom United Kingdom and Ireland (+44) 1784–442255 Fax (+44) 1784–461641 QMS Customer Support...
  • Page 178 QMS World-wide Offices QMS 2060 WX Print System User's Guide...
  • Page 179 Technical Specifications In This Appendix . . . Print engine specifications on page B-2 Controller specifications on page B-3 Environmental requirements on page B-3 Print media on page B-4 Cable pinouts on page B-6 Printer options on page B-8 Consumables on page B-9 Regulatory information on page B-10 Warranty information on page B-12...
  • Page 180 » Note: Actual print speed depends on the paper orientation and the host application. Resolution 300x300 dpi 600x600 dpi Toner Microfine toner designed especially for high-resolution printers; dry, single component in user-replaceable cartridge QMS 2060 WX Print System User's Guide...
  • Page 181 Controller Specifications Toner Cartridge A minimum of 10,000 simplex letter/A4-size pages at Life normal (5%) page coverage Type Desktop, non-impact printer Warm-Up Time 70 seconds or less, assuming normal temperature and humidity Weight Main unit 53 lbs/24kg Toner cartridge 4 lbs/1.9 kg Controller Specifications Fonts Windows 95 TrueType fonts...
  • Page 182 » Note: Print on perforated paper (including 3-hole- punched paper) from the multipurpose tray, not a cassette. Weights (Paper) Cassette 16–24 lb (60–90 g/m Duplexer 17–24 lb (64–90 g/m Multipurpose tray 17–42 lb (64–157 g/m QMS 2060 WX Print System User's Guide...
  • Page 183 Print Media Print Media Selection Input Source Cassettes Multipurpose Tray R = Recommended N = Not Recommended or Guaranteed Print Media Sizes Media Media Size Imageable Area Feed Input Edge Source Inches Millimeters Inches Millimeters 12x19 12.00x19.50 304.8x495.3 12.00x19.50 304.80x495.30 S 11.69x16.53 297.0x420.0 11.69x16.53 297.00x420.00 S 8.27x11.69...
  • Page 184 Direction Strobe- Data 1 InOut Data 2 InOut Data 3 InOut Data 4 InOut Data 5 InOut Data 6 InOut Data 7 InOut Data 8 InOut Acnlg- Busy+ Select Autofeed Reserved Ground Ground QMS 2060 WX Print System User's Guide...
  • Page 185 Cable Pinouts Signal Pin No. Signal Description Direction Vcc Test 19–30 Ground Iprime Fault- Reserved Reserved Reserved Selectin Notes to the Table Direction refers to the direction of signal flow as viewed from the printer. Return denotes “twisted-pair return” and is to be connected at signal-ground level.
  • Page 186 Media Cassettes 250-sheet universal media cassette (supports up to and Optional 11x17/A3 media). Feeder Optional feeder with a choice of a 500-sheet letter/A4 cassette or a second 250-sheet universal media cassette. QMS 2060 WX Print System User's Guide...
  • Page 187 QMS Laser Printer Transparencies (p/n 1710118-002) Use only transparency sizes letter or A4. Toner Keyed toner cartridges are available from your QMS vendor. See Cartridge appendix A, “QMS Customer Support, for a list of locations and telephone numbers. Technical Specifications...
  • Page 188 EU (International) IEC 825 FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. B-10 QMS 2060 WX Print System User's Guide...
  • Page 189 QMS documentation. ACHTUNG! Um elektrische Kurtzschlüsse zu vermeiden, entfernen Sie keine Gehaüseteile von Ihrem Drucker, wenn Sie keine Erfahrungen im Umgang mit elektrischen Bauteilen haben. Befolgen Sie die in der QMS Dokumentation beschriebenen Hinweise. Technical Specifications B-11...
  • Page 190 Power Cord The following power cord requirements are in effect for the 220V QMS 2060 WX Print System. Minimum 0.75 mm...
  • Page 191 However, if QMS printer failure or damage is found to be directly attributable to the use of non-QMS consumables and/or accessories, QMS will not repair the printer free of charge. In this case, standard time and material charges will be applied to service your printer for that particular failure or damage.
  • Page 193 TCP/IP Concepts In This Appendix . . . Terminology on page C-2 Subnetting on page C-4 Internet routing on page C-5...
  • Page 194 Each gateway has two addresses—one for each network that it connects. Internet The Internet is one or more networks connected by intelligent nodes, each of which is referred to as an Internet routers (IR). QMS 2060 WX Print System User's Guide...
  • Page 195 Terminology Internet Address An Internet address is a 32-bit address assigned to hosts connected to a TCP/IP network. It consists of an Internet part and a local part. While this address is expressed to the network in binary form, it is usually written in decimal form.
  • Page 196 32-bit subnet mask. Like Internet and subnet addresses, the subnet mask is written in binary form for the network. Bits are set to 1 if the network treats the corresponding bit in the QMS 2060 WX Print System User's Guide...
  • Page 197 Internet Routing Internet address as part of the network address, and to 0 if it treats the bit as part of the host identifier. For example, the binary subnet mask 11111111 11111111 11111111 00000000 specifies that the first three groups of eight digits in the Internet address identify the network and subnet and that the fourth group identifies the host on that subnet.
  • Page 198 7 bits 24 bits 0xFF000000 networks and many hosts Sites with some 14 bits 16 bits 0xFFFF0000 networks and some hosts Sites with many 21 bits 8 bits 0xFFFFFF00 networks and few hosts QMS 2060 WX Print System User's Guide...
  • Page 199 Brightness About... button 2-7 Windows NT printer driver 2-33 Accessories Buffers See Optional accessories Enlarging 4-12 Address Bulletin board, QMS A-3 Ethernet C-2 Buttons Ethernet Hardware 3-13 About... 2-7 Internet 3-10, C-3 Apply 2-7, 2-12 Router 3-12 Cancel 2-7, 2-9, 2-12, 2-21, 2-25, 2-31,...
  • Page 200 Eth. HW Address 3-13 (CIE Y) Internet Address 3-10 Windows NT printer driver, choosing Language 3-9 2-20 Options, selecting 3-8 Device Gamma Router 1 3-12 Windows NT printer driver, choosing Router 2 3-12 2-19 QMS 2060 WX User’’'s Guide — Index...
  • Page 201 Halftone color adjustments Brands, recommended B-9 Configuring, Windows NT printer driver Size, choosing 2-4, 2-23, 2-28 2-32 Environmental requirements B-3 Halftone pattern Erasing flash message 7-3 Windows NT printer driver, choosing Error diffusion 2-11 2-19 QMS 2060 WX User's Guide — Index...
  • Page 202 Input RGB Gamma 2-34 Laser safety B-12 Installation LEDs 3-4 Printer driver (manual installation) 7-32 Data 3-4 Intensity Disk 3-4 Choosing 2-12 Error 3-4 Setting 2-34 Ready 3-4 Internet C-2 Letterhead Address C-3 Printing 2-59 QMS 2060 WX User’’'s Guide — Index...
  • Page 203 Choosing 2-16 OK button 2-7, 2-9, 2-12, 2-21, 2-25, Meg ver x.x message 7-5 2-31, 2-35 Memory Online/Offline key 3-4 RAM,SIMMs 4-12 Open... button 2-36 Specifications B-3 Optional accessories B-8 Menu Cassettes 4-8 QMS 2060 WX User's Guide — Index...
  • Page 204 Using 2-44 Paper out multipurposer tray message Print Monitor,Network, QMS Using 2-40 Paper out upper tray message 7-6 Print quality Paper source 2-25 Black image, entire page 7-27 Choosing 2-16 Black stripes 7-31 QMS 2060 WX User’’'s Guide — Index...
  • Page 205 Return Merchandise Authorization 2-31, 2-35 number 6-2 Open... button 2-36 Returning, printer Restore Defaults button 2-7, 2-9, 2-12 RMA number 6-2 Revert button 2-21, 2-36 Revert button 2-21, 2-36 Save As... button 2-36 QMS 2060 WX User's Guide — Index...
  • Page 206 Print job active 7-6 Dimensions B-2 Printing need more memory 7-6, 7-24 Duty cycle B-2 Printing paper mismatch 7-6 Electrical requirements B-2 QMS 2060 WX test 7-6 Engine type B-2 Toner low 7-7 Environmental requirements B-3 Troubleshooting 7-12 Fonts B-3...
  • Page 207 Transmission Control Protocol/ White stripes 7-31 Internet Protocol TrueType fonts 7-25 See TCP/IP C-4 Transparencies Brands, recommended B-9 Choosing 2-7, 2-25, 2-30, 2-31 Updating printer driver 4-20 Print 2-57 Updating system software 4-19 QMS 2060 WX User's Guide — Index...
  • Page 208 Windows NT Network Print Monitor Using 2-40 Windows NT printer driver 2-20, 2-34 Black Ref. and White Ref. 2-34 Brightness 2-33 Configuration 2-12 Contrast 2-32 Copy Count, choosing 2-24 Dark Picture 2-33 Device Alignment White/Luminance I-10 QMS 2060 WX User’’'s Guide — Index...

Table of Contents