Advertisement
Quick Links
General Information
PLEASE READ THROUGH BEFORE BEGINNING ASSEMBLY.
IMPORTANT: Check boxes for Contents Listed
Check inside of parts as some parts are packaged
inside of others
In the event of missing, damaged or defective parts
please call our customer service dept. at 1-877-258-6020
When assembling components, place on a clean, flat
non-abrasive surface to avoid scratches
Tools Required
... Battery or Electric Drill
or
... Phillips Screwdriver
... Tape Measure
... Rubber Mallet or Hammer
(recommended)
with #2 phillips bit
(optional but recommended)
3 / 4' Rosebud Arbor
11107/08
Model#
Part #
1
⅞ x 1½ x 60½" Left Leg
2
⅞ x 1½ x 60½" Right Leg
3
⅞ x 1½ x 28" Top/Center Cross Rail
4
⅞ x 1½ x 28" Bottom Cross Rail
5
⅞ x 1½ x 18" Middle Cross Rail
6
⅝ x 61" Tube
7
⅝ x 56¾" Bent Tubes
8
⅞ x 1½ x 36 / 48" Arbor Top
9
¾ x 27 ⅞" Tube
10
⅞ x 1½ x 12" Flared Ground Anchor
11
Hardware Bag
⅝" Round Cap
¾" Painted Screw
150 Birch Road
P.O. Box 122
Sheboygan Falls, WI 53085
Assembly Instructions
Description
(with caps)
(includes:)
1-877-258-6020
www.dura-trel.com
sales@dura-trel.com
Qty
2
2
4
2
4
2
4
2
5
4
1
6
22
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Dura Trel Rosebud Arbor 11107/08
Summary of Contents for Dura Trel Rosebud Arbor 11107/08
- Page 1 3 / 4' Rosebud Arbor 11107/08 Model# Assembly Instructions Part # Description ⅞ x 1½ x 60½" Left Leg ⅞ x 1½ x 60½" Right Leg ⅞ x 1½ x 28" Top/Center Cross Rail ⅞ x 1½ x 28" Bottom Cross Rail ⅞...
- Page 2 Warranty Statement 20 Year Guarantee Please call manufacturer direct with questions concerning missing or defective parts at Toll Free: 877-258-6020. Dura-trel, Inc. products are warranted to be free from manufacturing defects resulting in delaminating, peeling, flaking, corroding, cracking, crazing, or extreme amounts of fading or bleaching causing the PVC to change to its natural color for a period of 20 years from the date of purchase.
- Page 3 On clean flat surface lay out two 61” bent tubes (part 7) and slide 28" top/center cross rails (part 3) and 18" center cross rails (part 5) over the bent tubes in the order shown. Note: Bent tubes are marked with a black mark on inside of tube to indicate top end. Repeat this process to make second assembly 3/4' Rosebud Arbor...
- Page 4 Lay one left leg (part 1) with routed holes facing up, pilot holes for screws facing you and flared end to the left. Starting at end of leg with flare insert cross rails from previous assembly. Insert 28" bottom cross rail (part 4) into last routed hole (end opposite of flared end) of leg and slide end of bent tubes (without black mark) into outer two holes of bottom rail.
-
Page 5: Installation
Insert five 27¾" tubes (part 9) into one bent arbor top (part 8). Insert free ends of tubes into remaining bent arbor top (part 8). Using six ¾" screws, screw together arbor top. Be sure tubes are fully inserted into arbor tops before. fastening Insert ends of arbor top into flared ends of each arbor panel to complete arbor.
Need help?
Do you have a question about the Rosebud Arbor 11107/08 and is the answer not in the manual?
Questions and answers