Directed DIRECTECHS DB3 Installation Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. Directechs DB3
  6. Installation manual

Directed DIRECTECHS DB3 Installation Manual

For audi q7 (smart key). 403.vw08 1.35 rsr
Hide thumbs Also See for DIRECTECHS DB3:
Table of Contents

Advertisement

Quick Links

INSTALLATION GUIDE
DB3
2020 Audi Q7 (Smart Key). 403.VW08 1.35 RSR
Designed by Installers for Installers
© 2021 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DIRECTECHS DB3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Directed DIRECTECHS DB3

Summary of Contents for Directed DIRECTECHS DB3

  • Page 1 2020 Audi Q7 (Smart Key). 403.VW08 1.35 RSR Designed by Installers for Installers © 2021 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s...

  • Page 2: Table Of Contents

    Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Installation Wiring diagram Wiring diagram (alternative installation) Locating components in the vehicle Locating components in the vehicle (alternative) Immobilizer interface with OEM immobilizer receiver (alternative) OEM Immobilizer - Removing the center console Vehicle connections SmartStart/XL202 installation notes Connecting the module...

  • Page 3: Introduction

    Introduction DB3 is an all-in-one door lock and override module. This guide supports the installation of a DB3 in Remote Start Ready (RSR) mode. This solution may offer up to three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation (if applicable, refer to the “Vehicle function compatibilities” below), RF System or SmartStart (all sold separately).

  • Page 4: Pre-Installation And Application Warnings

    Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness Keys required for Keys required for compatible programming operation Important!
  • Page 5 Wiring diagram Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( There are two possible installation methods for this vehicle. The alternative wiring diagram and information can be found following this method.

  • Page 6: Wiring Diagram (Alternative Installation)

    Wiring diagram (alternative installation) Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( Comfort System Module (blue/white conn. in left rear quarter panel, below fuse box) HS CAN 2 Low: You can connect to either a Orange/Brown, pin 1 HS CAN 1 High: Blue/Green, pin 6...

  • Page 7: Locating Components In The Vehicle

    Locating components in the vehicle 403.VW08 1.35 2020 Audi Q7 (Smart Key) ©2021 VOXX•DEI LLC. All rights reserved.

  • Page 8: Locating Components In The Vehicle (Alternative)

    Locating components in the vehicle (alternative) 403.VW08 1.35 2020 Audi Q7 (Smart Key) ©2021 VOXX•DEI LLC. All rights reserved.

  • Page 9: Immobilizer Interface With Oem Immobilizer Receiver (Alternative)

    Immobilizer interface Immobilizer interface (alternative installation) For vehicles with Keyless Entry you must remove battery from OEM key (the OEM remote may differ from For vehicles with Keyless Entry you must remove battery from OEM key (the OEM remote may differ from the models shown in the illustrations).

  • Page 10: Oem Immobilizer - Removing The Center Console

    OEM Immobilizer - Removing the center console in Audi Q7 Step 1: Gently pry and lift rear plate of center console. Step 2: Remove Torx screws on both ends. Step 3: Pull out rear trim of center console. Step 4: Remove Black 6 pin connector.

  • Page 11: Vehicle Connections

    Vehicle connections The connection information listed below is specific to the 2020 Audi Q7 (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes. Data 14-pin blue connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color H1/1...
  • Page 12 Output 12-pin red connector (H2) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color H2/1 Black/White No Connection No Connection H2/2 Green/Black (-) PTS Output Rear of Center Console, black 17 pin plug, pin 1 Yellow/Gray (PTS 1 Rear of Center Console, black 17 pin plug, pin 2 alternate) Rear of Center Console, black 17 pin plug, pin 3...
  • Page 13 D2D 4-pin white connector (H4) Module Conn./Pin Color Description H4/1 Green H4/2 Black H4/3 Blue H4/4 RF 2-pin white connector (H5) Module Conn./Pin Color Description H5/1 No Connection H5/2 No Connection 403.VW08 1.35 2020 Audi Q7 (Smart Key) ©2021 VOXX•DEI LLC. All rights reserved.

  • Page 14: Smartstart/Xl202 Installation Notes

    SmartStart/XL202 installation notes The DB3 Remote Start Ready (RSR) solution offers three (3) configuration options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart (both sold separately). This section provides specific installation information for SmartStart and XL202.

  • Page 15: Connecting The Module

    Connecting the module Important! Make all the required connections to the vehicle, as described in this guide, and double check to ensure everything is correct prior to moving onto programming. Note: Before connecting either the XL202 or SmartStart module to DB3, it is important to ensure that the proper feature and function programming is selected using DirectLink (version 4.5 or higher).

  • Page 16: Module Programming

    Module programming Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes. Connect the 10-pin, 12-pin and 14-pin harnesses to DB3, then wait until the LED turns ON solid red. Important! Do NOT depress the brake pedal. Press the Push-to-Start (PTS) button once to turn the ignition ON.

  • Page 17: Led Diagnostics And Troubleshooting

    LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black Module has no power.
  • Page 18 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence. received. Flashes green Ignition ON command received. The module has received the Ignition ON command and is processing the remote start sequence. Flashes red &...

  • Page 19: Parking Light Error Codes

    Parking light error codes The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown. Each flashing pattern is described below. Flashes Diagnostic Runtime expired. Over-rev shutdown. Low or no RPM. Shutdown without remote. Brake shutdown.

  • Page 20: Feature Programming

    Feature programming To enter feature programming routine: 1. Turn the ignition ON, then OFF. 2. Within 5 seconds, press and hold the programming button until the LED turns ON orange (after 3 seconds). 3. Release the Programming button. 4. The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current option of feature 1 (e.g.

  • Page 21: Feature And Option List

    Feature and option list It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page at www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page.

  • Page 22: Limited One Year Consumer Warranty

    This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.

  • Page 23: Quick Reference Guide

    • Aftermarket remote. Press the Remote Start button on the transmitter.* • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 If applicable, you can also start the engine remotely by pressing the Lock button 3 Press Remote vehicle is now in Pit Stop Mode.
  • Page 24 SmartStart compatible Note that the information below is for many Viper, Clifford, Python, Avital, Automate, This system is compatible with Directed SmartStart. For a complete list of supported Autostart and AstroStart models. Icons and commands may differ depending on the features, please visit www.mysmartstart.com.

Table of Contents