Summary of Contents for Backyard Discovery CARIBBEAN 1606029
Page 1
MANUFACTURED BY: Backyard Discovery 3305 Airport Drive, Pittsburg, KS 66762 800-856-4445 Basepoint Business Centre: Rivermead Drive,Westlea, Swindon SN5 7EX Phone: 0800-118-2476 J.P. Coenstraat 7, The Bridge, The Hague, 2595 WP, Netherlands Phone: 0800-567-8990 CARIBBEAN Swing Set Model # 1606029 The assembly manual must be retained...
Page 2
Basic Setup Dimensions Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. 20'-6 1/2" [6.3 m] 28'-5 1/2" 16'-5 1/2"...
Page 14
Parts Identification Accessories (NOT TO SCALE) - "A" REVISION TAG - A100314 (10) - QUICK LINK - A100069 - SWING HANGER - A4M00505 - SLIDE TUBE SUPPORT - A6P00487 - SWING SEAT GREEN 22" - A6P00054 - PLASTIC CURTAIN ROD - A6P00090 - METAL DECK BRACE 380 C/C - A4M00630 - TRAPEZE YELLOW - A6P00034 - SWING BEAM EXTENSION...
Page 15
Parts Identification Accessories (NOT TO SCALE) - CURTAIN - A6P00089 - CHAIN SUPPORT BRACKET BLK - A4M00632 - TIE STRAP PLATE BLK - A4M00631 - HAMMOCK - A6P00066 - SLIDE BED 10' LIGHT GREEN - A100035 - CHAIN - A4M00638 483 - SLIDE RAIL 10' BOTTOM LEFT GREEN - A6P00483 484 - SLIDE RAIL 10' BOTTOM RIGHT GREEN - A6P00484 - GREEN HC ROCK #1 - A6P00036...
Page 16
PRE-ASSEMBLY STEP 1 - SORTING PARTS It is critical for ease of assembly that you take the time to sort and organize the wood and hardware. WOOD PARTS: • Organize wood parts by the three-digit, alpha-numeric number stamped on each board (ex. P01). •...
Page 17
PRE-ASSEMBLY STEP 2 - TOOLS REQUIRED Drill Attachments: Phillips Head Open End Wrenches 1/2" & 9/16" 1/8", 3/16", 3/8" & 7/16" Drill Bits 3/8" Drive Ratchet, 1/2" & 9/16" STD Sockets 1/2" & 9/16" Deep Sockets Phillips Screw Driver Cordless Drill or Electric Drill Rubber Mallet - Optional Claw Hammer...
Page 18
PRE-ASSEMBLY STEP 3 - CHOOSE YOUR ASSEMBLY METHOD There are several types of assembly instructions available to you. 1. Printed Assembly Manual included with your set 2. BILT APP - 3D interactive instructions 3. Combination of the Printed Manual and BILT APP (Note: Step numbers can differ between the two methods)
Page 20
BOARD WITH T-NUTS M108 - TOP BOARD - W4L06331 5/8"x3 3/8"x29" (16x86x736) ROCKWALL ASSEMBLY STEP 2 SCREW PFH 8x1-1/2" M108 SCREW PFH 8x1-1/2" (2 PLCS) SCREW PFH 8x1-1/2" (4 PLCS) BOARD WITH T-NUTS (T-NUTS TO INSIDE)
Page 21
- GREEN HC ROCK #2 - A6P00037 - GREEN HC ROCK #1 - A6P00036 ROCKWALL ASSEMBLY STEP 3 BOLT PTH (24) 1/4x3/4 WASHER (24) LOCK INT 8x15 (24) T-NUT 1/4 BOLT PTH 1/4x3/4 GREEN HC ROCK #1 (24 PLCS) (6 PLCS) WASHER LOCK INT 8x15 (24 PLCS) GREEN HC ROCK #2...
Page 35
M70 - SLIDE SUPPORT BOARD - W100935 5/8"x3 3/8"x19 7/8" (16x86x505) SLIDE BED 10' LIGHT GREEN - A100035 STEP 1 10 FOOT SLIDE ASSEMBLY NOTE: BOLT WH 5/16x1/2 TAKE NOTE OF SLIDE BED SURFACE FINISH, THE DULL SIDE WILL BE TOWARDS THE GROUND.
Page 36
SLIDE RAIL 10' TOP RIGHT GREEN - A6P00486 SLIDE RAIL 10' BOTTOM RIGHT GREEN - A6P00484 SLIDE RAIL 10' TOP LEFT GREEN - A6P00485 SLIDE RAIL 10' BOTTOM LEFT GREEN - A6P00483 10 FOOT SLIDE ASSEMBLY STEP 2 NUT BARREL WH 5/16x1 1/2 NOTE: REPEAT ON OTHER SIDE, MAKING...
Page 37
A6P00487 SLIDE TUBE SUPPORT (x4) STEP 3 10 FOOT SLIDE ASSEMBLY NOTE: INSERT THE (4) SLIDE SUPPORT TUBES INTO THEIR RESPECTIVE PILOT LOCATIONS (FIGURE 1). BOLT WH 5/16x1 1/4 PLACE (1) SLIDE RAIL ASSEMBLY ON A FLAT SURFACE AND BEGIN INSERTING SLIDE BED AT THE BOTTOM OF THE SLIDE RAIL (FIGURE 2).
Page 38
10 FOOT SLIDE ASSEMBLY STEP 4 NOTE: PLACE SECOND SLIDE RAIL ASSEMBLY OVER THE TOP OF THE SLIDE BED AND SLIDE SUPPORT TUBES. INSERT THE SLIDE BED AND SLIDE SUPPORT TUBES INTO THE SLIDE CAVITY. MAKE SURE SLIDE BED IS INSERTED WITHIN 1/8" (3mm) OF GROOVE BOTTOM. FAILURE TO INSERT SLIDE BED PROPERLY MAY RESULT IN INJURY OR AMPUTATION.
Page 39
10 FOOT SLIDE ASSEMBLY STEP 5 NOTE: USE 1 1/4" BOLTS TO FASTEN EACH SIDE OF THE SLIDE SUPPORT TUBES. BOLT WH 5/16x1 1/4 TIP: HAVING A HELPER HOLD THE SLIDE ASSEMBLY TOGETHER WHILE YOU FASTEN WILL MAKE IT EASIER TO ASSEMBLE. BOLT WH 5/16x1 1/4 (4 PLCS)
Page 40
10 FOOT SLIDE ASSEMBLY STEP 6 NOTE: USING AN 1/8" DRILL BIT, DRILL PILOT HOLES IN EACH INDENTATION ALONG EACH SIDE RAIL. THERE SHOULD BE 15 INDENTATIONS ON (30) SCREW PFH 8x2 1/2 EACH RAIL. BE SURE TO DRILL THROUGH THE SLIDE RAIL AND THE SLIDE BED.
Need help?
Do you have a question about the CARIBBEAN 1606029 and is the answer not in the manual?
Questions and answers