Craftmade Revello REV52 Installation Manual
  1. Manuals
  2. Brands
  3. Craftmade Manuals
  4. Fan
  5. Revello REV52
  6. Installation manual

Craftmade Revello REV52 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Revello
Installation Guide
For Model:
REV52
E192641
net weight of fan: 16.94 lb (7.70 kg)
READ THESE INSTRUCTIONS
AND SAVE THEM FOR FUTURE USE

Table of Contents:

Warranty. pg. 11
page 1
PRINTED IN CHINA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Revello REV52 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Craftmade Revello REV52

Summary of Contents for Craftmade Revello REV52

  • Page 1: Table Of Contents

    READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Revello Installation Guide Table of Contents: For Model: Safety Tips. pg. 2 REV52 Unpacking Your Fan. pg. 3 Parts Inventory. pg. 3 Installation Preparation. pg. 4 Mounting Plate Installation. pg. 4 Preparation for Wiring.

  • Page 2: Safety Tips

    (2) this LED light kit must accept any interference received, including interference that may cause undesired operation. Distributed by: Craftmade, 650 S. Royal Lane, Coppell, TX, 75019; 1-800-486-4892 NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may occur.

  • Page 3: Unpacking Your Fan

    1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included.

  • Page 4: Installation Preparation

    3. Installation Preparation. blade edge To prevent personal injury and damage, ensure that inches 7 feet (76cm) the hanging location allows the blades a clearance (2.13m) of 7ft. (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square 12 ft.

  • Page 5: Preparation For Wiring

    safety 5. Preparation for Wiring. wood cable joist loop wood screw With wider opening facing up, place housing ring over and washer top of motor housing. Then, push housing ring down past top edge of motor housing. Lift motor housing to mounting plate and then hang motor housing on j-hook on underside of mounting safety plate.

  • Page 6: Fan Assembly

    6. Wiring. (cont.) [PLEASE NOTE: Wall and/or handheld remote control must be used for fan to operate. If you do not wish to outlet box wall control use the wall control, please proceed to Section 7 to continue with fan installation.] dimmer switch To install wall control, remove existing wall switch.

  • Page 7: Blade Assembly

    8. Blade Assembly. WARNING: To reduce the risk of serious motor housing bodily injury, DO NOT use power tools to assemble the blades. If screws are blade arm overtightened, blades may crack and break. Time Saver: Washers for blade attachment screws can be set on each screw prior to installing blades.
  • Page 8 9. Light Kit Assembly. (cont.) motor Remove 1 screw and partially loosen the other 2 housing screws on outer edge of fitter plate. Connect WHITE wire from motor housing to WHITE wire from LED light kit. Connect BLACK (or fitter plate BLUE) wire from motor housing to BLACK wire molex from LED light kit.

  • Page 9: Handheld Remote Control Assembly

    10. Handheld Remote Control Assembly. IN ORDER TO USE THE HANDHELD REMOTE CONTROL, remote control PLEASE CONTINUE WITH SECTION 10 for remote control cover assembly instructions. If you have already installed the wall control but do not wish to use the handheld remote control, please proceed to Section 11.

  • Page 10: Automated Learning Process./Activating Code

    11. Automated Learning Process./Activating Code. CAUTION: The wall and/or handheld remote control can be programmed to multiple receivers or fans. If this is not desired, turn wall switch off to any other programmable receiver or fan. Restore electrical power and then, if using wall control, set slider switch on wall control to the ON position. Within 60 seconds of turning on the wall control, press and hold the OFF button on the wall control for 5 seconds (or until light blinks twice or fan blades begin to turn).

  • Page 11: Troubleshooting

    RETURN FAN MOTOR ONLY, shipping prepaid, to 5. Check that red light on handheld remote control Craftmade Industries. We will repair or ship purchaser a turns on when a button is pressed indicating that the replacement motor and Craftmade will pay the return battery is good.

Table of Contents