Advertisement
3. SECURING SUPPORT PLATES AND WHEELS
Parts Required:
1
x
Right Front Leg (#11)
1
x
Right Back Leg (#12)
Right Bottom Support Plate (#16)
1
x
1
x
Short Support Plate (#18)
2
x
Wheel (#15)
8
x
Screw (#D)
Wheel Axle Pin (#E)
2
x
2
x
Wheel Cotter Pin (#F)
2
x
Wheel Washer (#G)
Installation:
•
Install one Short Support Plate to the side of the unit between of a Front
and Back Support Legs using four screws. Repeat the same installation
to mount the Bottom Support Plate to the same legs.
•
Attach the large Wheel to the Support Leg by inserting the Wheel Axle
Pin through the Wheel Support Leg hole, then secure using the Wheel
Cotter Pin. Repeat installation for other Wheel on the same side.
NOTE: Make sure Bottom Support Plate is facing up with correct direction.
4. SECURING SUPPORT PLATE TO SUPPORT LEGS FOR WHEELS
Parts Required:
2
x
Front/Back Long Support Plate (#19)
4
x
Screw (#D)
Installation:
•
Secure one Long Support Plate to one Support Leg for Wheel using two
screws. Ensure the flat side of the Support Plate is facing outwards.
Repeat the same installation to mount the other Long Support Plate to
the other Support Leg.
5. SECURING SUPPORT PLATE TO SUPPORT LEGS
Parts Required:
4
x
Screw (#D)
Installation:
•
Next, Secure the Long Support Plates to the Support Legs. Secure using
two screws for each plate.
6
3
12
11
18
16
E
G F
15
F G
E
15
4
19
19
5
6. MOUNTING MAIN BARREL TO THE CART
Parts Required:
1
x
Main Barrel (#4)
12 x
Screw (#A)
Washer (#B)
12 x
12 x
Locking Washer (#C)
1
x
Power Cord (#29)
1
x
Cable Clip (#28)
Installation:
•
Please replace with the correct power cord for your country, if you find
the power cord does not match the plug you are using.
•
Place the cable clips on the correct power cord. Insert the power cord
into the grove at the bottom of the hopper. Secure the cable clip to
the bottom of the hopper with the previously installed screw. Note
Illustration 6A.
•
Prepare the Main Barrel to be mounted to the cart. Carefully, lift the Cart
into an upright position with the Wheels on the bottom. Position the
Cart next to the Main Barrel, with both facing the same direction. Using
a second person, prepare to lift the Main Barrel onto the Cart. With one
person lifting from the hopper side, and the other person lifting from
the opposing barrel end, carefully lift the Main Barrel, and slowly lower
onto the cart. Note illustration 6B.
•
Next, open the Main Barrel lid. Adjust the rotation as needed to align the
screw holes of the Main Barrel to the Cart. Once placed, secure each leg
to the Main Barrel using three Screws, Washers, and Locking Washers.
Note illustration 6C.
7. INSTALLING THE LID STOPPER
Parts Required:
Lid Stopper (#1)
1
x
Installation:
•
Secure the Lid Stopper onto the top of the Main Barrel using the pre-
installed screw on top of the Main Barrel.
8. INSTALLING THE LID HANDLE
Parts Required:
Lid Handle (#2)
1
x
2
x
Lid Handle Bezel (#3)
Installation:
•
Remove the pre-installed screws from the Lid Handle. From inside the
barrel lid, insert one screw protrude to the outside. Add a Bezel on
the screw. Then hand-tighten the screw (from the inside) into the Lid
Handle. Repeat for other side.
6A
28
29
6B
4
6C
A
C
B
7
1
2
8
3 3
7
Advertisement
