Advertisement
9. INSTALLING THE FLAME BROILER COMPONENTS
Parts Required:
1
x
Flame Broiler Main Plate (#8)
1
x
Flame Broiler Slider (#7)
Installation:
•
Insert the Flame Broiler Main Plate into the main grill. Rest the Flame
Broiler Main Plate on the built-in ledge (on the inside right) of
the main grill that directs grease towards the grease bucket spout. Slide
the entire piece to the left side, and the two slots on the Flame Broiler
Main Plate will fit into the rounded ledge above the burn pot. It will sit
slightly at a downward angle. Note illustration 9A.
IMPORTANT: If the Main Plate is resting on the base of the Barrel,
it is installed incorrectly. Poor installation may result in damage to
your Main Grill Barrel.
•
Place the Flame Broiler Slider on top of the Flame Broiler Main Plate
covering the slotted openings. Ensure the raised tab is on the left
and the two pins at the bottom of the Flame Broiler Slider place into
the holes of the Flame Broiler Main Plate to easily adjust for direct and
indirect flame when cooking. Both flame broiler parts are lightly
coated with oil to avoid rusting when shipped. Note illustration 9B.
NOTE: To maintain the searing and grilling performance of your cooking
grids, regular care and maintenance Is required. See Owner's Manual.
10. INSTALLING FLAME BROILER ADJUSTING BAR
Parts Required:
1
x
Flame Broiler Adjusting Bar (#5)
Flame Broiler Adjusting Bar Handle (#6)
1
x
Installation:
•
Insert the Flame Broiler Adjusting Bar through the opening hole on
the left side of the Main Barrel. Add the Flame Broiler Adjusting Bar
Handle on the end outside the barrel. Next, slide the notched end of the
Adjusting Bar into the locking tab on the Flame Broiler Slider, giving you
adjustable access to the Flame Broiler Slider on the Main Plate.
11. INSTALLING THE SIDE SHELF
Parts Required:
1
x
Right Side Table (#24)
2
x
Screw (#A)
2
x
Washer (#B)
Locking Washer (#C)
2
x
Installation:
•
Loosen the two pre-installed screws from the side of the Main Barrel.
Hook up the Right Side Table on the screws first then secure the two
pre-loosened screws into place.
•
From underneath, secure the Right Side Table to the side panel of the
Main Barrel using two screws, washers, and locking washers.
8
9A
8
9B
7
8
10
B
C
A
5
B
C
5
6
11
24
BCA
12. SECURING THE FRONT SHELF BRACKETS
Parts Required:
1
x
Front Shelf Bracket Right (#21)
1
x
Front Shelf Bracket Left (#22)
Screw (#A)
4
x
4
x
Washer (#B)
4
x
Locking Washer (#C)
Installation:
•
Secure each Front Shelf Support Bracket onto the Front Support Leg by
using two screws, washers and locking washers.
13. INSTALLING THE FRONT SHELF
Parts Required:
Front Shelf (#20)
1
x
Installation:
•
Place the Front Shelf on the Front Shelf Support Brackets. Note
illustration 13A as unfolded Front Shelf.
•
Note illustration 13B as folded Front Shelf.
•
Front Shelf can also be placed on the Bottom Support Plates and be used
as Bottom Plate. Note illustration 13C.
14. INSTALLING THE GRILL COOKING COMPONENTS
Parts Required:
2
x
Cooking Grids (#25)
1
x
Warming Rack (#26)
Installation:
•
Place the Cooking Grids, side by side, on the grid ledge inside the Main Grill.
•
Place the Upper Warming Rack on the upper ledge inside the Main Grill.
The Warming Rack will lock into place.
12
22
21
ACB
ACB
13A
20
13B
20
13C
20
14
26
25
25
9
Advertisement
