Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for WATSON 360.394.1300
Summary of Contents for WATSON 360.394.1300
- Page 1 ASSEMBLY Haven Recharge Bench 360.394.1300 watsonfurniture.com V.21.2 1/2022...
- Page 2 Recharge Bench Components Seat Cushions Support Rail Bridge Legs Neighborhood Light Accessory Planter Tray Accessory Oblong Surface Accessory Round Surface Accessory 2 HAVEN RECHARGE BENCH ASSEMBLY INSTRUCTIONS...
- Page 3 Hardware Main Bench Hardware 10 X 3/4” Pan M6-1.0 X 12mm 1/4 - 20 X 7/8” #6 X 3/4” Pan Head Head Screw (125285) Button Head Screw Screw (122500) (122875) (0000750) Planter Tray Accessory Hardware M8 Nylock Nut M8 Washer, 23mm M8 1”...
- Page 4 Tools Electric Drill T25 Tor x Bit 4mm Hex Bit Phillips Bit Adjustable Wrench 13mm Wrench 4 HAVEN RECHARGE BENCH ASSEMBLY INSTRUCTIONS...
- Page 5 Assemble Bench Base Place the support rail on a soft surface with the large slots facing up. Slide each bridge leg into the ends of the support rail and secure with (4) screws each. M6-1.0 X 12mm (125285) 5 HAVEN RECHARGE BENCH ASSEMBLY INSTRUCTIONS...
- Page 6 Attach Seat Cushions to Base Place the cushions under the base. For each cushion, align the three holes in the base with the appropriate pilot holes in the cushion. Drive (3) screws per side. 1/4 - 20 X 7/8” Button Head Screw (0000750) 6 HAVEN RECHARGE BENCH ASSEMBLY INSTRUCTIONS...
- Page 7 Optional Power Unit The optional power unit can be mounted on either side of the bench. Locate the four pilot holes on the underside of the seat cushion that the power unit will mount to. Slide the power unit into the bracket so the four holes line up. Align the assembly with the pilot holes in the cushion, and secure the power unit with (4) screws.
- Page 8 Optional Planter Tray Place the Planter Tray stem through the center hole in the support rail of the bench. From the underside of the support Rail, slide the spacer (0002196) and washer (0001567) onto the stem of the Planter Tray, and spin the nut (0001248) onto the stem by hand.
- Page 9 Optional Oblong Surface Place the Oblong Surface upside down on a soft surface. Attach the mounting plate and stem by aligning the plate with the pilot holes, making sure the table stem is justified to the outside of the table. Secure the plate with (6) screws (0002148) (a.).
- Page 10 Optional Round Surface Place the Round Surface upside down on a soft surface. Attach the mounting plate and stem by aligning the plate with the pilot holes. Secure the plate with (6) screws (0002148) (a.). Place the table assembly through the center hole in the support rail of the bench.
- Page 11 Optional Neighborhood Light: Attach Light Rod Pass the small connector cables in the light stem through the light rod (a.) and slide the light rod over the cable and up to the light stem (b.). Screw the light rod into the threaded plate in the light stem, and use the flat sections on the end of the light rod to tighten fully into the bottom of the lamp (c.).
- Page 12 Optional Neighborhood Light: Position Light Stem Pass the cables through the hole in the bench and insert the light rod into the mounting hole. Position the light stem so the alignment pins go through the alignment holes in the bench frame. 12 HAVEN RECHARGE BENCH ASSEMBLY INSTRUCTIONS...
- Page 13 Optional Neighborhood Light: Secure Light Stem Pass the cables through the mounting washer, spacer, lock washer, and mounting nut and secure the stem to the bench frame by tightening the mounting nut. Mounting Washer Locking Washer Mounting Nut Spacer (used only for the bench assembly) 13 HAVEN RECHARGE BENCH ASSEMBLY INSTRUCTIONS...
- Page 14 Optional Neighborhood Light: Attach Connector Housing Once you have secured the lamp stem, attach the connector housings onto the ends of the cables. Once inserted, gently pull on the wire to ensure a strong connection. Connector Housing 14 HAVEN RECHARGE BENCH ASSEMBLY INSTRUCTIONS...
- Page 15 Optional Neighborhood Light: Attach Light Disc Plug the connector from the light disc into the connector from the stem (a.) and feed the excess cable down into the stem. Secure the light disc to the stem using (3) flat head screws (b.). Thread Cutting Screw M4 X 12mm...
- Page 16 Optional Neighborhood Light: Secure Power Supply Secure the power supply to the bench using (2) screws and the power supply mounting bracket. 10 X 3/4” Pan Head Screw (122875) 16 HAVEN RECHARGE BENCH ASSEMBLY INSTRUCTIONS...
- Page 17 Optional Neighborhood Light: Connect Power Connect the plugs from the power supply to the connectors on the light, making sure to connect red to red and black to black. Tuck any excess cable into the bench frame tube to keep it out of the way. Plug into power source and test. 17 HAVEN RECHARGE BENCH ASSEMBLY INSTRUCTIONS...
- Page 18 Optional Neighborhood Light: Attach Light Shade Press the shade onto the light disc, applying even pressure around the perimeter until a snug and level fit. 18 HAVEN RECHARGE BENCH ASSEMBLY INSTRUCTIONS...
Need help?
Do you have a question about the 360.394.1300 and is the answer not in the manual?
Questions and answers