Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Acclaim Lighting Aqua Graze
Summary of Contents for Acclaim Lighting Aqua Graze
- Page 1 Aqua Graze User guide...
-
Page 3: Table Of Contents
CONTENTS INTRODUCTION ............2 Welcome Safety, maintenance and cleaning INSTALLATION ............3 Aqua Graze mounting and adjusting Aqua Driver mounting Control input connections Creating a wireless DMX input Converting a 0-10V input Output connections Port connection cables Fixture support with Aqua Driver 150... -
Page 4: Introduction
INTRODUCTION WELCOME Welcome to the Aqua Graze and Aqua Driver from Acclaim Lighting. This range of high output, submersible LED flood fixtures offer IP68 submersible properties thanks to their anodized oxidation aluminum housings and fully sealed joints. There are two sizes of fixture: •... -
Page 5: Installation
INSTALLATION AQUA GRAZE MOUNTING AND ADJUSTING When installing Aqua Graze fixtures, ensure that the surface is level and that nothing is protruding to damage the mounting brackets. Suitable mounting surfaces include steel, aluminum, concrete or wood structures. Each mount bracket has two slots measuring 0.39”... -
Page 6: Aqua Driver Mounting
AQUA DRIVER MOUNTING Both Aqua Driver models can be wall mounted either vertically or horizontally as required. Two slotted holes (Ø 0.23” x 0.47” / Ø 6 x 12mm) are available on each side for mounting purposes - see “Dimensions” on pages 19 and 20. CONTROL INPUT CONNECTIONS Both Aqua Driver models can either operate in a standalone manner or be controlled by DMX. -
Page 7: Creating A Wireless Dmx Input
CREATING A WIRELESS DMX INPUT The optional Acclaim Lighting Aria units allow you create a wireless DMX link up to 2600 feet (792m) line of sight, between your control output and the Aqua Driver. Setup and configuration is straightforward: 1 Connect the DMX output of one Aria unit to the DMX input (using either the terminal block or the XLR connector) of the Aqua Driver. -
Page 8: Output Connections
“Aqua Driver mode control” on page 14). PORT CONNECTION CABLES Each Aqua Graze fixture is supplied with a 100’ (30m) cable terminated in an 8-pin terminal connector. In situations where this supplied cable is shortened and then wired into a... -
Page 9: Fixture Support With Aqua Driver 150
AQUA GRAZE 1’ FIXTURES Up to four Aqua Graze 1’ fixtures can be used on a single Aqua Driver 150. Any of the port grouping options (1 Group, 2 Group or 4 Group - see page 10) are appropriate for these fixtures. -
Page 10: Fixture Support With Aqua Driver 400
AQUA GRAZE 1’ FIXTURES Up to eight Aqua Graze 1’ fixtures can be used on a single Aqua Driver 400. Any of the port grouping options (1 Group, 2 Group, 4 Group or 8 Group - see page 10) are appropriate for these fixtures. -
Page 11: Connector Pin Outs
CONNECTOR PIN OUTS AQUA GRAZE RGBW/A These connections are used for RGBW/A versions of the EO, SO and HO Aqua Graze fixtures: Black R– Green G– Yellow B– White W– AQUA GRAZE WHITE These connections are used for White versions of the EO, SO and HO Aqua Graze fixtures: Black Circuit 1–... -
Page 12: Port Grouping
PORT GROUPING AQUA DRIVER 150 The four output ports can either be used individually under separate control or grouped in either pairs, or grouped all as one control block. The grouping status is determined by switches 1 and 2 of the 6-way switch block (see page 14). 2 Group 4 Group 1 Group... -
Page 13: Dmx Channel Layouts
DMX CHANNEL LAYOUTS The number of DMX channels required to control the connected fixtures depends upon the following settings, which are configured using the 6-way switch block: • Port grouping, and • Fixture type AQUA DRIVER 150 The various DMX channel requirements for the various port grouping and fixture type combinations on the Aqua Driver 150 are listed here: RGBW/A RGBW/A... - Page 14 AQUA DRIVER 400 The various DMX channel requirements for the various port grouping and fixture type combinations on the Aqua Driver 400 are listed here: RGBW/A RGBW/A RGBW/A RGBW/A address 8 Group 4 Group 2 Group 1 Group Port 1: Ports 1 &...
-
Page 15: Power Input
POWER INPUT The fixed power cord is supplied as standard with US color coding and bare tails. For international installations, wire according to local codes. The Aqua Driver power requirements are as follows: • Voltage: 100-277VAC 50/60Hz Power cord colors The red front panel indicator will illuminate when power is applied. -
Page 16: Aqua Driver Mode Control
8 group See “Port grouping” on page 10 for more details. 4 Use switches 4 and 5 of the 6-way switch block to Fixture type set the type of Aqua Graze fixtures being used: Fixture type White RGBW/A Note: The chosen fixture type (RGBW/A or White) is applied globally to all ports. - Page 17 STANDALONE MODE USING INTERNAL CHASE PROGRAMS In standalone mode, all four ports are treated as one group. Note: all switch settings can be changed when the driver is off or on. To configure the Aqua Driver for standalone chase mode you need to: 1 On the 10-way switch block, set switch 10 OFF to Standalone mode: OFF...
- Page 18 • • • • dimming level (for all emitters of every connected Aqua Graze fixture). When all eight switches are OFF, the fixtures will be at 0%; conversely, all switches ON will produce 100% output. The switches are arranged as a...
-
Page 19: Further Information
FURTHER INFORMATION AQUA GRAZE AND DRIVER SPECIFICATIONS AQUA GRAZE FIXTURES Color models 2700K, 3000K, 3500K and 4000K white RGBW (W=4000K), RGBA Beam angle options x 10 , 25 x 25 , 40 x 40 , 60 x 60 , 10... -
Page 20: Dimensions
DIMENSIONS AQUA GRAZE 1' (305mm) 3.07” (78mm) Ø0.48” (Ø12.3mm) 0.39 x Ø0.18” (10 x Ø4.5mm) 2.13" 2.56" (54mm) (65mm) 4' (1220mm) 23.94” (608mm) Ø0.48” (Ø12.3mm) Fixture weights: 1’ models: 1.5 lbs (0.68 kg) 4’ models: 6 lbs (2.72 kg) www.acclaimlighting.com... -
Page 21: Aqua Driver 150
DIMENSIONS AQUA DRIVER 150 Aqua Driver 150 11.04" (280.5mm) 2.6" (66mm) 10.24" (260mm) Ø0.24 x 0.47" ( 6 x 12mm) Ø DMX OUT OUTPUT POWER STAND ALONE MANUAL DMX IN 11.83" (300.5mm) Weight: 2.6 lbs (1.18 kg) www.acclaimlighting.com... -
Page 22: Aqua Driver 400
DIMENSIONS AQUA DRIVER 400 Weight: 4.4 lbs (1.99 kg) www.acclaimlighting.com... -
Page 23: Limited Product Warranty
If the requested repairs or service (including parts replacement) are within the terms of this warranty, Acclaim Lighting will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package. - Page 24 www.acclaimlighting.com...