Installation Environment; Placement Of Plc - FATEK FBS Series Manual

Chapter 4
1. Turn off all power during installation of FB
damage to equipment.
2. Upon completion of all installation wiring, put the protective cover back on the terminal block before
turning on the power to avoid electrical shock.
3. During installation, never remove the dust cover sheet that were surrounded the PLC before wiring is
completed to avoid complications such as fire hazards, breakdown, or malfunction caused by drill dust
or wire shreds falling inside PLC.
4. Upon completion of installation and wiring, remember to remove the dust cover sheet to avoid fire,
breakdown or malfunction, caused by overheating.

4.1 Installation Environment

1. Environmental specifications of FB
operate this equipment in environments with oil smoke, conductive dust, high temperatures, high
humidity, corrosion gases, inflammable gases, rain or condensation, and high vibrations and shock.
2. This product has to be housed appropriately whether it's used in a system or standalone. The choice and
installation of housing must comply with local national standards.
4.2 Precautions of PLC Installation
To avoid interference, the PLC should be installed to keep from noise sources such as high- voltage or high-current
lines and high power switches. Other precautions ar
4.2.1

Placement of PLC

Fixation of FB
S
the left to the expansion unit on the right. A typical figure of placement is shown below:
Suggested arrangement
of multiple unit expansion
多台擴充之
建議排列方式
Installation Guide
-PLC, which can be fixed by DIN RAIL or screws, should place vertically and start from the main unit on
max. 24V OUT X0 X2 X4 X6 X8 X10 X12
400mA S/S X1 X3 X5 X7 X9 X11 X13
0 I 2 3
4 5 6 7
8 9 I0 I I
I2 I3
IN X ( )
POW
PROGRAMMABLE RUN
CONTROLLER
ERR
TX RX
OUT Y ( )
0 I 2 3
PORT0 4 5 6 7
8 9
IN AC100~240V
Y1 Y2 Y4 Y5 Y6 Y8 SINK
SRCE
C0 Y0 C2 Y3 C4 C6 Y7 Y9
FATEK

Danger
-PLC or related equipments to prevent electric shock or
S

Note
-PLC cannot exceed those listed in this manual. In addition, do not
S
e:
X1 X3 X5 X7 X9 X11 X13
S/S X2 X4 X6 X8 X10 X12 X14
0 I 2 3
4 5 6 7
I I
8 9 I0
I2 I3
IN X ( )
PROGRAMMABLE
CONTROLLER
POW
OUT Y ( )
0 2 3
I
4 5 6 7
8 9
Y2 Y3 Y5 Y6 Y7 Y9 SINK
SRCE
C1 Y1 C3 Y4 C5 C7 Y8 Y10
max. 24V OUT X1 X3 X5 X7 X9 X11 X13
400mA S/S X2 X4 X6 X8 X10 X12 X14
0 I 2 3
4 5 6 7
8 9 I0 I I
I2 I3
IN X ( )
PROGRAMMABLE
CONTROLLER
POW
OUT Y ( )
0 I 2 3
4 5 6 7
8 9
IN AC100~240V
SINK
Y2 Y3 Y5 Y6 Y7 Y9
SRCE
C1 Y1 C3 Y4 C5 C7 Y8 Y10
H4 -1
X1 X3 X5 X7 X9 X11 X13
S/S X2 X4 X6 X8 X10 X12 X14
0 I 2 3
4 5 6 7
8 9 I0 I I
I2 I3
IN X ( )
PROGRAMMABLE
CONTROLLER
POW
OUT Y ( )
0 I 2 3
4 5 7
6
8 9
SINK
Y2 Y3 Y5 Y6 Y7 Y9
Y1 Y4 Y8 Y10 SRCE
C1 C3 C5 C7
X1 X3 X5 X7 X9 X11 X13
S/S X2 X4 X6 X8 X10 X12 X14
0 I 2 3
4 5 6 7
8 9 I0 I I
I2 I3
IN X ( )
PROGRAMMABLE
CONTROLLER
POW
OUT Y
( )
0 2 3
I
4 5 6 7
8 9
Y2 Y3 Y5 Y6 Y7 Y9 SINK
SRCE
C1 Y1 C3 Y4 C5 C7 Y8 Y10