Installation Environment; Plc Installation Precautions; Placement Of Plc - FATEK FBs Series User Manual

Chapter 4
1. Turn off all power during installation of FB
damage to equipment.
2. Upon completion of all installation wiring, put the protective cover back on the terminal block before
turning on the power to avoid electrical shock.
3. During installation, never remove the dust cover sheet that were surrounded the PLC before wiring is
completed to avoid complications such as fire hazards, breakdown, or malfunction caused by drill dust
or wire shreds falling inside PLC.
4. Upon completion of installation and wiring, remember to remove the dust cover sheet to avoid fire,
breakdown or malfunction, caused by overheating.

4.1 Installation Environment

1. Environmental specifications of FB
operate this equipment in environments with oil smoke, conductive dust, high temperatures, high
humidity, corrosion gases, inflammable gases, rain or condensation, and high vibrations and shock.
2. This product has to be housed appropriately whether it's used in a system or standalone. The choice and
installation of housing must comply with local national standards.

4.2 PLC Installation Precautions

To avoid interference, the PLC should be installed to keep from noise sources such as high- voltage or high-current
lines and high power switches. Other precautions ar
4.2.1

Placement of PLC

Fixation of FB -PLC, which can be fixed by DIN RAIL or screws, should place vertically and start from the main unit on
S
the left to the expansion unit on the right. A typical figure of placement is shown below:
Suggested arrangement
multiple unit expansion
Installation Guide
S
max. 24V OUT X0 X2 X4 X6 X8 X10 X12
400mA X11 X13
S/S X1 X3 X5 X7 X9
0 I 2 3
4 5 6 7
I0 I I
8 9
I2 I3
IN X
( )
POW
PROGRAMMABLE
RUN
CONTROLLER
ERR
TX RX
OUT Y
( )
0 I 2 3
PORT0
4 5 6 7
8 9
FBs-24MCR2-AC
AC100~240V
IN
Y1 Y2 Y4 Y5 Y6 Y8
C0 Y0 C2 Y3 C4 C6 Y7 Y9
24V OUT X1
max.
400mA S/S X2
PROGRAMMABLE
CONTROLLER
IN AC100~240V
Y2
C1 Y1 C3

Danger
-PLC or related equipments to prevent electric shock or
S

Caution
-PLC cannot exceed those listed in this manual. In addition, do not
e:
X1 X3 X5 X7 X9 X11
X10
S/S X2 X4 X6 X8
0 I 2 3
4 5 6 7
I0 I I
8 9
I2 I3
IN X
( )
PROGRAMMABLE
CONTROLLER
POW
OUT Y
( )
0 I 2 3
4 5 6 7
9
8
Y2 Y3 Y5 Y6 Y7 Y9
C1 Y1 C3 Y4 C5 C7 Y8
X3 X5 X7 X9 X11 X13
X4 X6 X8 X10 X12 X14 S/S
0 I 2 3
4 5 6 7
I0 I I
8 9
I2 I3
IN X
( )
PROGRAMMABLE
CONTROLLER
POW
OUT Y
( )
0 I 2 3
4 5 6 7
8 9
FBs-24XYR
Y3 Y5 Y6 Y7 Y9
C1
Y4 C5 C7 Y8 Y10
H4-1
X1 X3 X5 X7
X13
S/S X2 X4 X6
X12 X14
0
4
8
I2
PROGRAMMABLE
CONTROLLER
0
4
8
FBs-24XYR
Y2 Y3 Y5 Y6
C1 Y1 C3 Y4 C5
Y10
X1 X3 X5 X7 X9 X11 X13
X2 X4 X6 X8 X10 X12 X14
0 I 2 3
4 5 6 7
I0 I I
8 9
I2 I3
IN X ( )
POW
OUT Y
( )
0 I 2 3
4 5 6 7
8 9
FBs-24XYR
Y2 Y3 Y5 Y6 Y7 Y9
Y1 C3 Y4 C5 C7 Y8 Y10
X9 X11 X13
X8 X10 X12 X14
I 2 3
5 6 7
I0 I I
9
I3
IN X
( )
POW
OUT Y
( )
2 3
I
5 6 7
9
FBs-24XYR
Y7 Y9
C7 Y8 Y10