Download
Share
Print this page
FATEK FB Series Manual
  1. Manuals
  2. Brands
  3. FATEK Manuals
  4. Controller
  5. FB Series
  6. Manual

FATEK FB Series Manual

Sio driver
Hide thumbs Also See for FB Series:

Advertisement

Quick Links

FB Series SIO Driver
1
System Configuration....................................................................................................... 3
2
Selection of External Device ............................................................................................ 8
3
Example of Communication Setting ................................................................................. 9
4
Setup Items .................................................................................................................... 32
5
Cable Diagram ............................................................................................................... 37
6
Supported Devices......................................................................................................... 63
7
Device Code and Address Code.................................................................................... 65
8
Error Messages.............................................................................................................. 66
FATEK AUTOMATION Corporation
1

Advertisement

loading

Related Manuals for FATEK FB Series

Summary of Contents for FATEK FB Series

  • Page 1: Table Of Contents

    FATEK AUTOMATION Corporation FB Series SIO Driver System Configuration....................... 3 Selection of External Device .................... 8 Example of Communication Setting ................. 9 Setup Items ........................32 Cable Diagram ....................... 37 Supported Devices......................63 Device Code and Address Code..................65 Error Messages......................66...
  • Page 2 FB Series SIO Driver Introduction This manual describes how to connect the Display and the External Device. In this manual, the connection procedure will be described by following the sections below: System Configuration "1 System Configuration" (page 3) This section shows the types of External Devices that can be connected and SIO type.

  • Page 3: System Configuration

    FB Series SIO Driver System Configuration The following shows the system configuration where the External Device of FATEK AUTOMATION Corporation and the Display are connected. Setting Cable Series Link I/F SIO Type Example Diagram Setting Cable CPU unit Port 0...
  • Page 4 FB Series SIO Driver Setting Cable Series Link I/F SIO Type Example Diagram Setting Cable Port 3 RS232C Example 6 Diagram 3 (page 18) (page 38) FBs-CM25E Setting Cable RS422/485 Port 4 Example 9 Diagram 4 (2wire) FBs-10MA/MC (page 24)
  • Page 5 FB Series SIO Driver Setting Cable Series Link I/F SIO Type Example Diagram Setting Cable FBe-20MC Port 0 RS232C Example 11 Diagram 3 FBe-28MC (page 27) (page 38) FBe/FBn FBe-40MC FB-DTBR-E FBn-19MCT Setting Cable RS422/485 FBn-26MCT Port 2 Example 13...
  • Page 6 FB Series SIO Driver COM Port on IPC When the External Device is connected to the IPC, the COM port available depends on the series and SIO type. Refer to your IPC manual for details. Usable Port Usable Port Series...
  • Page 7 FB Series SIO Driver DIP Switch Setting: RS-422/485 (4wire) DIP Switch Setting Setup Description Reserved (always OFF) SIO type: RS-422/485 Output mode of SD (TXD): Always output Ω Termination resistor (220 ) inserted into SD (TXD): None Ω Termination resistor (220...

  • Page 8: Selection Of External Device

    Corporation". Select the model (series) of the External Device to be connected and its connection method. Select "FB Series SIO". Check the External Device that can be connected in "FB Series SIO" in system Series configuration. "1 System Configuration" (page 3) Check this option to synchronize the system data area of the Display and the device (memory) of the External Device.

  • Page 9: Example Of Communication Setting

    FB Series SIO Driver Example of Communication Setting The following shows examples of communication settings for the Display and the External Device, which are recommended by Pro-face. Setting Example 1 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace.
  • Page 10 FB Series SIO Driver Setting Example 2 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
  • Page 11 FB Series SIO Driver Settings of External Device Use the ladder software (WinProladder) for communication settings. After completing the settings, reboot the External Device to enable them. Refer to your External Device manual for details. Start up the ladder software (WinProladder).
  • Page 12 FB Series SIO Driver Setting Example 3 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
  • Page 13 FB Series SIO Driver Settings of External Device Use the ladder software (WinProladder) for communication settings. After completing the settings, reboot the External Device to enable them. Refer to your External Device manual for details. Start up the ladder software (WinProladder).
  • Page 14 FB Series SIO Driver Setting Example 4 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
  • Page 15 FB Series SIO Driver Settings of External Device Use the ladder software (WinProladder) for communication settings. After completing the settings, reboot the External Device to enable them. Refer to your External Device manual for details. Start up the ladder software (WinProladder).
  • Page 16 FB Series SIO Driver Setting Example 5 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
  • Page 17 FB Series SIO Driver Settings of External Device Use the ladder software (WinProladder) for communication settings. After completing the settings, reboot the External Device to enable them. Refer to your External Device manual for details. Start up the ladder software (WinProladder).
  • Page 18 FB Series SIO Driver Setting Example 6 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
  • Page 19 FB Series SIO Driver Settings of External Device Use the ladder software (WinProladder) for communication settings. After completing the settings, reboot the External Device to enable them. Refer to your External Device manual for details. Start up the ladder software (WinProladder).
  • Page 20 FB Series SIO Driver Setting Example 7 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
  • Page 21 FB Series SIO Driver Settings of External Device Use the ladder software (WinProladder) for communication settings. After completing the settings, reboot the External Device to enable them. Refer to your External Device manual for details. Start up the ladder software (WinProladder).
  • Page 22 FB Series SIO Driver Setting Example 8 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
  • Page 23 FB Series SIO Driver Settings of External Device Use the ladder software (WinProladder) for communication settings. After completing the settings, reboot the External Device to enable them. Refer to your External Device manual for details. Start up the ladder software (WinProladder).
  • Page 24 FB Series SIO Driver Setting Example 9 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
  • Page 25 FB Series SIO Driver Settings of External Device Use the ladder software (WinProladder) for communication settings. After completing the settings, reboot the External Device to enable them. Refer to your External Device manual for details. Start up the ladder software (WinProladder).
  • Page 26 FB Series SIO Driver 3.10 Setting Example 10 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. • For 1:n connection, set [Wait To Send] to a value of the PLC scan time plus 5ms or more.
  • Page 27 FB Series SIO Driver 3.11 Setting Example 11 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. • For 1:n connection, set [Wait To Send] to a value of the PLC scan time plus 5ms or more.
  • Page 28 FB Series SIO Driver 3.12 Setting Example 12 Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. • For 1:n connection, set [Wait To Send] to a value of the PLC scan time plus 5ms or more.
  • Page 29 FB Series SIO Driver Settings of External Device Use the ladder software (WinProladder) for communication settings. After completing the settings, reboot the External Device to enable them. Refer to your External Device manual for details. Start up the ladder software (WinProladder).
  • Page 30 FB Series SIO Driver 3.13 Setting Example 13 Settings of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. • For 1:n connection, set [Wait To Send] to a value of the PLC scan time plus 5ms or more.
  • Page 31 FB Series SIO Driver Settings of External Device Use the ladder software (WinProladder) for communication settings. After completing the settings, reboot the External Device to enable them. Refer to your External Device manual for details. Start up the ladder software (WinProladder).

  • Page 32: Setup Items

    FB Series SIO Driver Setup Items Set the communication settings of the Display with GP-Pro Ex or in off-line mode of the Display. The setting of each parameter must match that of the External Device. "3 Example of Communication Setting" (page 9)
  • Page 33 FB Series SIO Driver Setup Items Setup Description In case of no response from the External Device, enter how many times the Display Retry retransmits the command, from "0 to 255". Enter the standby time (ms) from when the Display receives packets until it transmits the Wait To Send next command, from "0 to 255".
  • Page 34 FB Series SIO Driver Settings in Off-Line Mode • Refer to the Maintenance/Troubleshooting manual for information on how to enter off-line mode or about the operation. Maintenance/Troubleshooting Manual "2.2 Off-line Mode" Communication Settings To display the setting screen, touch [Device/PLC Settings] from [Peripheral Equipment Settings] in off-line mode.
  • Page 35 FB Series SIO Driver Setup Items Setup Description Enter the time (s) for which the Display waits for a response from the External Device, Timeout from "1 to 127". In case of no response from the External Device, enter how many times the Display Retry retransmits the command, from "0 to 255".
  • Page 36 FB Series SIO Driver Option To display the setting screen, touch [Device/PLC Settings] from [Peripheral Equipment Settings]. Touch the External Device you want to set from the list that appears, and touch [Option]. Setup Items Setup Description You can switch between RI/VCC of the 9th pin when you select RS232C for the SIO type.

  • Page 37: Cable Diagram

    FB Series SIO Driver Cable Diagram The cable diagram shown below may differ from that recommended by the FATEK AUTOMATION Corporation. Please be assured, however, that there is no operational problem in applying the cable diagram shown in this manual.
  • Page 38 FB Series SIO Driver Cable Diagram 2 Display Cable Remarks (Connection Port) GP (COM1) ST (COM1) Cable length: Your own cable 15m or less PC/AT Available only with a COM port that supports RS232C. COM Port on IPC (page 6)
  • Page 39 FB Series SIO Driver Cable Diagram 4 Display Cable Remarks (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 (COM1) Connector terminal block conversion adapter by Pro-face AGP-3302B (COM2) CA3-ADPTRM-01 (COM2) Your own cable Your own cable Online adapter by Pro-face...
  • Page 40 FB Series SIO Driver A. When using the COM port conversion adapter (CA3-ADPCOM-01), the connector terminal block conversion adapter (CA3-ADPTRM-01) by Pro-face, and your own cable • 1:1 Connection Display Terminal block Signal name TERM Shield External Device Terminal block...
  • Page 41 FB Series SIO Driver B. When using your own cable • 1:1 Connection Display D-Sub 9 pin (socket) Terminal resistance Signal name Shield Ω External Device (1/2W) Terminal block Signal name Display Terminal resistance: ON Shell • 1:n Connection Display...
  • Page 42 FB Series SIO Driver C. When using the online adapter (CA4-ADPONL-01), the connector terminal block conversion adapter (CA3- ADPTRM-01) by Pro-face, and your own cable • 1:1 Connection Display Terminal block Signal name TERM Shield External Device Terminal block Display...
  • Page 43 FB Series SIO Driver D. When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable • 1:1 Connection Display D-Sub 9 pin (plug) Signal name TERMRX Shield External Device CA4-ADPONL-01 Terminal block Display Signal name TERMTX Terminal resistance: ON...
  • Page 44 FB Series SIO Driver E. When using the COM port conversion adapter (CA3-ADPCOM-01), the connector terminal block conversion adapter (CA3-ADPTRM-01) by Pro-face, and your own cable • 1:1 Connection Display Terminal block External Device Shield Signal name Terminal block TERM...
  • Page 45 FB Series SIO Driver F. When using your own cable • 1:1 Connection External Device Display Shield Terminal block D-Sub 9 pin (socket) Terminal resistance Signal name Signal name Ω (1/2W) DATA+ DATA- Display Terminal resistance: ON GND(SG) Shell • 1:n Connection...
  • Page 46 PC/AT Cable FB-232P0-9M-150 by FATEK Available only with a COM port that supports RS232C. COM Port on IPC (page 6) A. When using your own cable and the cable FB-232P0-9F-150 by FATEK Connection Cable Display D-Sub 9 pin (socket) D-Sub 9 pin (plug)
  • Page 47 FB Series SIO Driver Cable Diagram 6 Display Cable Remarks (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 (COM1) Connector terminal block conversion adapter by Pro-face AGP-3302B (COM2) CA3-ADPTRM-01 (COM2) Your own cable Your own cable Online adapter by Pro-face...
  • Page 48 FB Series SIO Driver A. When using the COM port conversion adapter (CA3-ADPCOM-01), the connector terminal block conversion adapter (CA3-ADPTRM-01) by Pro-face, and your own cable • 1:1 Connection Display Terminal block Signal name TERM Shield External Device Terminal block...
  • Page 49 FB Series SIO Driver B. When using your own cable • 1:1 Connection Display D-Sub 9 pin (socket) Terminal resistance Signal name Shield Ω External Device (1/4W) Terminal block Terminal resistance Signal name Ω (1/4W) Display Shell • 1:n Connection...
  • Page 50 FB Series SIO Driver C. When using the online adapter (CA4-ADPONL-01), the connector terminal block conversion adapter (CA3- ADPTRM-01) by Pro-face, and your own cable • 1:1 Connection Display Terminal block Signal name TERM Shield External Device Terminal block Terminal...
  • Page 51 FB Series SIO Driver D. When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable • 1:1 Connection Display D-Sub 9 pin (plug) Signal name TERMRX Shield CA4-ADPONL-01 External Device Terminal block Display Terminal resistance Signal name Ω...
  • Page 52 FB Series SIO Driver E. When using the COM port conversion adapter (CA3-ADPCOM-01), the connector terminal block conversion adapter (CA3-ADPTRM-01) by Pro-face, and your own cable • 1:1 Connection Display Terminal block External Device Shield Signal name Terminal block Terminal...
  • Page 53 FB Series SIO Driver F. When using your own cable • 1:1 Connection External Device Display Shield D-Sub 9 pin (socket) Terminal block Terminal Terminal resistance resistance Signal name Signal name Ω Ω (1/4W) (1/4W) DATA+ DATA- Display GND(SG) Shell •...
  • Page 54 FB Series SIO Driver Cable Diagram 7 Display Cable Remarks (Connection Port) GP (COM1) ST (COM1) Cable length: Your own cable 15m or less PC/AT Available only with a COM port that supports RS232C. COM Port on IPC (page 6)
  • Page 55 FB Series SIO Driver Cable Diagram 8 Display Cable Remarks (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 (COM1) Connector terminal block conversion adapter by Pro-face AGP-3302B (COM2) CA3-ADPTRM-01 (COM2) Your own cable Your own cable Online adapter by Pro-face...
  • Page 56 FB Series SIO Driver A. When using the COM port conversion adapter (CA3-ADPCOM-01), the connector terminal block conversion adapter (CA3-ADPTRM-01) by Pro-face, and your own cable • 1:1 Connection Display Terminal block Signal name TERM Shield External Device D-Sub 15 pin (plug)
  • Page 57 FB Series SIO Driver B. When using your own cable • 1:1 Connection Display Terminal D-Sub 9 pin (socket) resistance Signal name Shield Ω (1/4W) External Device Terminal D-Sub 15 pin (plug) resistance Signal name Ω (1/4W) Display Shell • 1:n Connection...
  • Page 58 FB Series SIO Driver C. When using the online adapter (CA4-ADPONL-01), the connector terminal block conversion adapter (CA3- ADPTRM-01) by Pro-face, and your own cable • 1:1 Connection Display Terminal block Signal name TERM Shield External Device Terminal D-Sub 15 pin (plug)
  • Page 59 FB Series SIO Driver D. When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable • 1:1 Connection Display D-Sub 9 pin (plug) Signal name TERMRX Shield CA4-ADPONL-01 External Device D-Sub 15 pin (plug) Terminal Display resistance Signal name Ω...
  • Page 60 FB Series SIO Driver E. When using the COM port conversion adapter (CA3-ADPCOM-01), the connector terminal block conversion adapter (CA3-ADPTRM-01) by Pro-face, and your own cable • 1:1 Connection Display Terminal block External Device Shield Signal name D-Sub 15 pin (plug)
  • Page 61 FB Series SIO Driver F. When using your own cable • 1:1 Connection Display External Device Shield D-Sub 9 pin (socket) Terminal D-Sub 15 pin (plug) Terminal resistance resistance Signal name Signal name Ω Ω (1/4W) (1/4W) DATA+ DATA- Display...
  • Page 62 FB Series SIO Driver Cable Diagram 9 Display Cable Remarks (Connection Port) GP (COM1) ST (COM1) Cable length: Your own cable 15m or less PC/AT Available only with a COM port that supports RS232C. COM Port on IPC (page 6)

  • Page 63: Supported Devices

    FB Series SIO Driver Supported Devices The following table shows the range of supported device addresses. Available type and range of device may vary depending on the CPU. Consult the appropriate CPU manual before use. : This address can be specified as system data area.
  • Page 64 FB Series SIO Driver No data can be written to word addresses HR5000 to HR8071 and R05000 to R08071. Write disable The file register is supported only by the FBs Series. • Refer to the GP-Pro EX Reference Manual for system data area.

  • Page 65: Device Code And Address Code

    FB Series SIO Driver Device Code and Address Code Use device code and address code when you select "Device Type & Address" for the address type of the data display or other devices. Device Code Device Device Name Address Code...

  • Page 66: Error Messages

    FB Series SIO Driver Error Messages Error messages are displayed on the Display screen as follows: "No.: Device Name: Error Message (Error Occurrence Area)". Each description is shown below. Item Description Error No. Name of the External Device where an error has occurred. Device name is the title of the Device Name External Device set with GP-Pro EX.

This manual is also suitable for:

Fbs seriesFbe seriesFbn seriesFbe-20mcFbe-28mcFbe-40mc ... Show all