Vitek VT-8188 Manual Instruction page 4

ENGLISH
floor, the surface that needs to be cleaned, before pro-
ceeding. We also recommend reading the instructions
for use and care from the floor manufacturer.
•
Place the unit vertically on an even, dry, moisture- and
heat-resistant surface, do not place it horizontally and
do not turn it over during the operation.
•
Use only the attachments supplied.
•
Before using the unit, make sure that the steam head is
set and fixed properly.
•
It is recommended to fill the water tank with tap water
which was additionally cleaned with domestic filters.
Do not use carbonated water or any perfume additives.
•
The unit generates very hot steam for disinfection of the
operating area. It means that the floor brush and the
cloth become very hot during the operation.
Caution: always wear suitable footwear when using the
steam mop and when changing accessories on the steam
mop. Do not wear slippers or open toe shoes.
•
The unit body can heat up strongly during the opera-
tion. Do not touch hot surfaces with your hands. Be
careful! Possible danger of burns!
•
Avoid getting burns by hot steam.
•
Unplug the unit after usage or before cleaning.
•
When unplugging the unit hold the power plug and
remove it from the mains socket, do not pull the power
cord – this can lead to its damage and cause short cir-
cuit.
•
The unit is not intended for usage by children.
•
Do not leave children unattended to avoid them using
the unit as a toy.
•
Do not allow children to touch the operating surface,
unit body, power cord or power plug during operation
of the unit.
•
Be especially careful if children or disabled persons are
near the operating unit.
•
During the unit operation and breaks between opera-
tion cycles, place the unit out of reach of children.
•
The unit is not intended to be used by people with phys-
ical, sensory or mental disabilities (including children)
or by persons lacking experience or knowledge if they
are not under supervision of a person who is respon-
sible for their safety or if they are not instructed by this
person on the usage of the unit.
•
For child safety reasons do not leave polyethylene bags
used as packaging unattended.
Attention! Do not allow children to play with polyethylene
bags or packaging film. Danger of suffocation!
•
From time to time check the power cord integrity.
•
If the power cord is damaged, it should be replaced
by the manufacturer, a maintenance service or similar
qualified personnel to avoid danger.
•
Do not use the unit if the power cord or the power plug
is damaged, if the unit works improperly and after it
was dropped.
•
Do not repair the unit by yourself. Do not disassemble the
unit by yourself, if any malfunction is detected or after it
VT-8188.indd 4
was dropped, unplug the unit and apply to any authorized
service center at the contact addresses given in the war-
ranty certificate and on the website www.vitek.ru.
•
To avoid damages, transport the unit in the original
package only.
•
Keep the unit in a dry cool place out of reach of children
and disabled persons.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY.
ITS COMMERCIAL USE AND USE IN PRODUCTION AND
WORKING AREAS ARE PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low temperature
keep it for at least three hours at room temperature.
•
Unpack the unit and remove any packaging materials
and advertising stickers.
•
Keep the original package.
•
Read the safety measures and operating recommen-
dations.
•
Check the delivery set.
•
Examine the unit for damages; if the unit is damaged,
do not plug it into the mains.
•
Make sure that the indicated specifications of the
power supply voltage of the unit correspond to the
specifications of your mains.
•
To remove dust clean the unit with a slightly damp cloth,
and then wipe it dry.
ASSEMBLING THE STEAM MOP
Note: Each steam mop passes 100% testing at the factory
to guarantee the working ability and safety of the product.
When assembling a new steam mop for the first time you
can find some water remaining inside the unit. This is not
a defect.
•
Remove the unit from the packaging making sure the
product is not damaged and that all parts are included
in the package.
•
Insert the handle (11) into the extension pipe (9) until
clicking, having preliminary pressed the clamp button
(13) (pic. 1).
•
To detach the handle (11) press the clamp button (13)
and pull the handle out of the extension pipe (9).
•
Insert the extension pipe (9) into the upper part of the
steam mop body (3) until clicking (pic. 1).
•
To detach the extension pipe (9) press the release but-
ton (15) and pull the handle out of the unit body.
•
Insert the body with the extension pipe and the handle
into the floor brush (1) so the floor brush release button
(2) goes into the opening in the unit body (3) (pic. 2).
•
To detach the unit body from the brush, slightly press
the brush down to the floor with your foot, press the
release button (2) and pull the unit body upwards.
•
Due to the special design of the hinge, the floor brush
(1) has a large rotation angle, so it can clean corners as
well as low space under furniture (pic. 5).
4
9/18/20 4:44 PM