Briggs & Stratton 020619-00 Manual page 6

7-in-1 Nozzle
Figure
The 7-in-1 nozzle allows you to switch between seven
different spray pattern nozzles. Release trigger on spray
gun to engage safety lock before changing spray patterns.
1. Select desired spray pattern:
• Select Maximum 0° nozzle (A) for stubborn cleaning
tasks such as paint removal, oil stains, rust removal or
other stubborn substances (tar, gum, grease, wax, etc.).
• Select General 15° nozzle (B) for tougher cleaning
tasks. Ideal for removing grease and dirt from hard
surfaces. Also capable of stripping paint when held
at a 45° angle.
• Select Gentle 40° nozzle (C) for gentle cleaning
of cars/trucks, boats, RV's, patio furniture, lawn
equipment, etc.
• Select Fan Spray nozzle (D) for optimal high flow
rinsing away of light dirt and debris.
• Select Fan Spray with Soap nozzle (F) for delicate
surface cleaning of cars, trucks, childrens play
equipment, patio furniture, etc.
• Select Extended Reach nozzle (G) for quick high
flow clean up and long reach cleaning of second
story siding and windows.
• Select Extended Reach with Soap Nozzle (H) to
propell soap to second story siding and windows.
2. Turn dial until desired spray pattern aligns with arrow
on 7-in-1 nozzle.
Usage Tips
• For most effective cleaning, keep nozzle from
20 to 61 cm (8 to 24 in.) away from cleaning surface.
• If nozzle gets too close, especially using a high pressure
nozzle, you may damage surface being cleaned.
• DO NOT get closer than 15 cm (6 in.) when cleaning tires.
Applying Detergent
WARNING! Chemicals could cause burns resulting
in death or serious injury. DO NOT use caustic liquid
with pressure washer. Use ONLY pressure washer
safe detergents/soaps. Follow manufacturers instructions.
To apply detergent, follow these steps:
1. Remove cap from detergent tank (D) and fill with
detergent solution. Replace cap.
2. Make sure one of the soap spray pattern nozzles is
selected on 7-in-1 nozzle.
NOTICE Detergent cannot be applied with high pressure
nozzles (maximum, general, delicate, fan spray or
extended reach).
3. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
4. Allow detergent to "soak in" per detergent
manufacturer's instructions before washing and rinsing.
6
12
Figure
3
Pressure Washer Rinsing
1. Select desired high pressure nozzle.
WARNING! Kickback from spray gun could cause
you to fall resulting in death or serious injury.
Operate pressure washer from a stable surface.
Be extremely careful if you must use the pressure washer
from a ladder, scaffolding, or any other similar location.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
2. Apply high pressure spray to a small area and check surface
for damage. If no damage is found, continue rinsing.
3. Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.
Stopping Pressure Washer
1. Release spray gun trigger.
2. Press master ON/OFF switch (E) to OFF (0) position.
NOTICE Releasing the trigger will shut off the motor but
does not shut off electrical power to the unit.
3. Turn off water supply.
4. ALWAYS point spray gun in a safe direction, press
trigger lock button, and squeeze trigger to relieve built
up pressure in the unit.
WARNING! The high pressure stream of water
that this equipment produces could cut through
skin and its underlying tissues, resulting in serious
injury and possible amputation. Keep high pressure hose
connected to pump and spray gun while system is
pressurized. DO NOT allow CHILDREN to play with or
operate pressure washer. ALWAYS point spray gun in safe
direction, squeeze spray gun trigger to release high
pressure, every time you turn off pressure washer.
5. Disconnect PRCD plug (G) from outlet and coil power
cord on bottom hook of accessory tray.
6. Wrap high pressure hose on top hook of accessory tray.
7. Store high pressure nozzle on end of nozzle
extension. Store spray gun, nozzle extension, and
7-in-1 nozzle on the accessory tray.
After Each Use
Water should not remain in the unit for long periods of time.
Sediments or minerals can deposit on pump parts and "freeze"
pump action. Follow these procedures after every use:
1. Run pressure washer with soap nozzle until tank is empty.
2. Add 0.5 liter (0.5 quart) of water to detergent tank, and
run with soap spray nozzle. Flush one to two minutes.
3. Press master ON/OFF switch to OFF (0) position.
Remove power cord plug from electrical outlet.
4. Turn off water supply. Point gun in a safe direction,
press trigger lock button, and squeeze trigger to
relieve trapped pressure.
Figure
3
BRIGGSandSTRATTON.COM