Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Esse-ti ST56 GMV
Summary of Contents for Esse-ti ST56 GMV
- Page 1 Alarm system for elevators ST56 GMV QUICK GUIDE 19/02/2014...
-
Page 2: Hardware Description
HARDWARE DESCRIPTION Picture 1 Jumper JP8 for define the behaviour of alarm inputs AL1and AL2 LEDs indicating device operation (red) and GSM200 signal strength (green) Connectors for AL100 power supply Connectors for optional relay board Serial plug for connection to elevator CPU Reset pushbutton RJ11 connector for local telephone RJ45 connector for GSM200 module... - Page 3 Terminal blocks BATT 12Vdc power supply input Received alarm indicator light Given alarm indicator light Output 12Vdc (max. 100mA) Alarm input 1 Alarm input 2 Common terminal for inputs IN1, Reset Alarm filter input Reset Reset input VV2+ Output Handsfree 2 VV2- Common Handsfree 2 VV1+...
- Page 4 Jumper JP8 for inputs AL1 and AL2 The jumper JP8 (A in picture 1) defines the behaviour of the inputs AL1 and AL2. The inputs AL1 and AL2 are at +12V; the alarm occurs when they are closed to a – terminal (ex: VV2-). The inputs AL1 and AL2 are at 0V;...
-
Page 5: Connecting The Telephone Line
CONNECTING THE TELEPHONE LINE The alarm system is ready for connection over the GSM line by the proprietary GSM200. It allows the connection of a PSTN line or an universal GSM gateway with the optional PSTN-line board. GSM200 Module Connection ... - Page 6 CORRECT OPERATION CHECKLIST 1. PROGRAMMING Access to programming: lift the local telephone handset and dial You will hear the dialling tone (one longer tone followed by a shorter tone). Program the telephone line type (PSTN or GSM-dedicated): dial for GSM200 module or for PSTN line or traditional GSM interfaces.
- Page 7 LINE (INST) GSM200 module SOURCE: RECEIVER: emergency- ADEMCO call button technological USER alarm … (X…X = TELEPHONE periodic (position telephone ESSE-TI NUMBERS test call from 01 number, (INST) to 12) max 20 digits) (only with GSM200) P100 PROGRAMMING Page 7...
- Page 8 DEAD BATTERY disabled alarm ALARM enabled alarm (INST) ADEMCO 4-digits ID: PROTOCOL ID (INST) ESSE-TI/P100 10-digits ID: PROTOCOL ID (INST) Frequency (days, from 1 to 9; factory default 3) Time (hhmm; from 0000 to 2359) AUTOMATIC TEST DATA...
- Page 9 PROGRAMMING (loudspeaker’s volume; HANDSFREE 1 HANDSFREE factory default 4) VOLUMES (mocrophone’s (INST/OPER) HANDSFREE 2 sensitivity; factory default 8) MESSAGES (volume) VOLUMES MESSAGES (message factory default 2) (INST/OPER) EMERGENCY BUTTONS closed NORMALLY OPEN/CLOSED open (INST) EMERGENCY BUTTON DELAY (seconds, from 0 to 9; factory default 2 ) (INST) FILTER disabled...
- Page 10 PROGRAMMING CONNECTION TIME AFTER AUTOMATIC (minutes, from 1 to 9; factory default 3 ) ANSWER (INST) CHANGING THE INSTALLER … (old) (new) (new) PASSWORD (INST) LISTENING TO (prefix programming code) PROGRAMMING RESTORING FACTORY DEFAULT (INST) Page 10 PROGRAMMING...
- Page 11 In the tables below: : lift the local telephone handset; : lift the local telephone handset and dial to access programming. Local LOCAL USE CONVERSATION WITH ALL THE CONVERSATION HANDSFREE TERMINALS OUTGOING CALLS <TELEPHONE NUMBER> RELAY (with RELAY 1 optional board) RELAY 2 Remote use with ST56 in stand-by...
- Page 12 TEL. +39 0321 677611 - FAX +39 0321 677690 http://www.gmv.it - e-mail: info@gmv.it Esse-ti s.r.l. Via G. Capodaglio, 9 Zona industriale Squartabue 62019 Recanati (MC) – ITALY Tel. ++39 071 7506066 – 7506105 Fax ++39 071 7506057 www.esse-ti.it mail: assistenza@esse-ti.it...
Need help?
Do you have a question about the ST56 GMV and is the answer not in the manual?
Questions and answers