Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Esse-ti Helpy GSM
Summary of Contents for Esse-ti Helpy GSM
-
Page 1: Quick Guide
Alarm system for elevators QUICK GUIDE 15/09/2017... - Page 2 INSTALLING Internal power-supply connector Built-in backup battery connector Antenna cable connector Reset pushbutton Alarm pushbutton SIM Card slot with front panel Built-in loudspeaker connector Serial port for PC connection (not present) RJ11 connector for local telephone Battery compartment door Terminal blocks Built-in microphone Page 2 INSTALLING...
-
Page 3: Terminal Blocks
LED signalling alarm / periodical test call (yellow) LED signalling GSM signal strength (green) LED signalling GSM status (red) LED signalling power supply status (blue) Terminal blocks NAME DESCRIPTION POWER SUPPLY INPUT (11-14VDC) – GIVEN ALARM INDICATOR LIGHT (output: 12VDC) RECEIVED ALARM INDICATOR LIGHT (output: 12VDC) 12VDC OUTPUT (max. - Page 4 NSERTING THE CARD Before inserting the SIM card, make sure the device is off and use all due precaution to avoid electrostatic discharge. Remove the cover by unscrewing the two screws. Push the SIM Card housing cover as indicated by the arrow OPEN until it unlocks and lift it.
-
Page 5: Push Button
ONNECTING THE HANDSFREE TERMINALS HelpyGSM comes with a built-in active handsfree terminal. It is also possible to connect to the HelpyGSM: up to 2 independent active handsfree terminals up to 2 passive handsfree terminals (or cables with microphone) combined to the integrated active handsfree terminal. It makes HelpyGSM extremely flexible and allows to realize many different types of installation. - Page 6 Installation with active handsfree terminal in the pit HANDSFREE PUSHBUTTON DEVICE terminal blocks terminal blocks ROOF HelpyGSM Built-in active handsfree Built-in pushbutton – – Microphone cable MIC3 / ALC / – – Active handsfree VVY / ALY / PROGRAMMING CODES "TYPE OF INSTALLATION" TO BE SET 730 (factory) Installation with landing floors HANDSFREE...
- Page 7 ONNECTING THE EMERGENCY CALL BUTTONS Car pushbutton It is possible to connect (inside the elevator car) voltage free contact pushbuttons or powered pushbuttons. Connect, following one of the diagrams shown below, the car pushbutton. Voltage free contact pushbuttons Powered pushbuttons (12~24Vdc) – 2 solutions INSTALLING Page 7...
- Page 8 Other pushbuttons It is possible to use for the pit, the car-top or the landing floors, voltage free contact pushbuttons (NO). Connect, following the diagram shown below, the other pushbuttons. Page 8 INSTALLING...
- Page 9 ONNECTING THE INDICATOR LIGHTS The GIVEN ALARM INDICATOR LIGHT (yellow) switches on after pressing the emergency button to indicate the beginning of the alarm procedure and stays steady light until the end. The RECEIVED ALARM INDICATOR LIGHT (green) switches on when the alarm call is answered. ...
-
Page 10: Connecting The Relay
ONNECTING THE FILTER INPUT Connect the filter contact as per one of the modes shown in the table: FILTER CONTACT C1 TERMINAL CONNECTED TO: TERMINAL BLOCKS – IN1 / – IN1 / external reference IN1 / external reference ONNECTING THE AUXILIARY INPUT ... -
Page 11: Wiring Diagram
– E IRING DIAGRAM XAMPLE INSTALLING Page 11... - Page 12 – E IRING DIAGRAM XAMPLE Page 12 INSTALLING...
-
Page 13: Power Connection
URNING ON Power connection Connect the power supply cable to the 230Vac mains. Connect an external 12Vdc power supply (min. 11Vdc, max. 14Vdc) to the power supply input of the terminal block (+ and terminals) – Connect the built-in backup battery cable to the slot B in the picture at page 2. - Page 14 INIMUM OPERATIONS TO VERIFY PROPER INSTALLATION 1. PROGRAMMING Access to programming: lift the local telephone handset and dial The programming activated message will be heard. Program a telephone number for the emergency-call alarm: dial < telephone number > ...
-
Page 15: Using The Reset Button
SING THE RESET BUTTON Use of the reset pushbutton (D in the picture at page 2): Pressing shortly Allows to interrupt an alarm call. By pressing shortly you get the same result as lifting the handset of the local telephone and entering * <Password> #. Pressing longer (10 seconds) Allows to reset the device. -
Page 16: Quick Programming Guide
PROGRAMMING (factory setting: EXITING THE <INSTALLER or OPERATOR PASSWORD> PROGRAMMING (factory setting: SOURCE RECEIVER emergency- USER call button battery … technology ESSE-TI (X…X = alarm TELEPHONE telephone (position NUMBERS number, from 01 to periodic (INST) max 20 automatic test digits) -
Page 17: Installation
BASIC PROGRAMMING WEEKDAY SUNDAY MONDAY TUESDAY DATE (INST) (dd) (mm) (yy) WEDNESDAY THURSDAY FRIDAY SATURDAY TIME (hhmm; from 0000 to 2359) (INST) identification message (max. 25s) RECORD THE MESSAGES (record) (hang up) (INST) courtesy message (max. 25s) identification LISTEN TO THE message MESSAGES (listen) - Page 18 Time of the (hhmm; from 0000 to 2359) call AUTOMATIC TEST DATA Enabling automatic test disabled (INST) automatic test automatic test enabled Manually perform a test call PROTOCOLS Esse-ti IDENTIFICATION … (identification CODE code) P100 (INST) built-in active handsfree terminal HANDSFREE handsfree...
-
Page 19: Advanced Programming
BASIC PROGRAMMING LISTEN TO THE PROGRAMMING (programming code prefix) AGAIN (INST) RESTORE FACTORY SETTINGS (INST) Advanced programming ADVANCED PROGRAMMING CHANGE INSTALLER … PASSWORD (old) (new) (new) (INST) CHANGE OPERATOR … PASSWORD (old) (new) (new) (INST) EMERGENCY CALL BUTTONS DELAY (seconds, from 2 to 9) (INST) CAR EMERGENCY normally closed... - Page 20 ADVANCED PROGRAMMING handsfree activation by “Handsfree activation” code HANDSFREE CONNECTION automatic handsfree activation after MODE DURING messages AN ALARM (INST) immediate and automatic handsfree activation (no messages) ALARM RESET automatic reset MODE (INST) alarm reset by “End alarm” code “ACKNOWLEDGE” CODE …...
-
Page 21: Relay Setting
ADVANCED PROGRAMMING CALL CYCLES FOR TECHNOLOGICAL (cycles, from 1 to 9; 0= 10 cycles; ALARMS AND factory default 3) TEST CALLS (INST) CALL CYCLES FOR EMERGENCY CALL (cycles, from 1 to 9; 0= unlimited) ALARMS (INST) AUTOMATIC (ring number, from 1 to 9; ANSWER 0= 10 rings;... - Page 22 ADVANCED PROGRAMMING ASSIGN NEW PIN … (PIN) … (PIN) (INST) DISABLE PIN REQUEST (INST) RESTORE PIN REQUEST (INST) emergency-call button battery technology alarm TEST OF ALARMS periodic automatic test call (INST) no external power supply alarm auxiliary alarm Page 22 QUICK PROGRAMMING GUIDE...
-
Page 23: Programming Via Sms
PROGRAMMING VIA SMS Programming via SMS can be performed from any mobile phone or other device that can send SMS messages. An SMS notifying the programming was performed is sent by the HelpyGSM to the number that sent the programming. ATTENTION Programmed performed via SMS sent from the Internet could not have a positive result if the... -
Page 24: Quick Use Guide
QUICK USE GUIDE In the tables: : lift the local telephone handset : lift the local telephone handset and dial to access programming Local use LOCAL USE CONVERSATION CONVERSATION WITH THE CAR CAR HANDSFREE TERMINAL CONVERSATION WITH ONE HANDSFREE TERMINAL CONNECTED TO VVY HANDSFREE HANDSFREE TERMINAL CONNECTED TO VVX... - Page 25 SIGNALS LED signalling alarm / periodical test call (yellow) Emergency-call alarm Emergency call alarm suspended Other alarms - Test call LED signalling GSM signal strength (green) No signal Low signal level Medium signal level Good signal level High signal level SIGNALS Page 25...
- Page 26 LED signalling GSM status (red) GSM module correctly registered on the network HelpyGSM registering to the GSM network – HelpyGSM not registered correctly – PIN request – PIN incorrect – Other problems Call in progress LED signalling power supply status (blue) The external power supply is connected and the battery has max capacity charge...
-
Page 27: Troubleshooting
The external power supply is disconnected and the battery guarantees up to 7-hour operation in idle state The external power supply is disconnected and the battery guarantees 2-hour operation in idle state The external power supply is disconnected and the battery guarantees 1-hour operation in idle state Troubleshooting DETECTED PROBLEM... - Page 28 HelpyGSM edition 15/09/2017 Esse-ti S.r.l. Via G. Capodaglio, 9 62019 Recanati (MC) – ITALY Tel. +39 071 7506066 Fax +39 071 7506057 www.esse-ti.it e-mail: support@esse-ti.it...
Need help?
Do you have a question about the Helpy GSM and is the answer not in the manual?
Questions and answers